Andersen Panel Assumbly Installation guide

Brand: Andersen

Model: Panel Assumbly

Type: Installation guide

Panel Assembly, Installation, and Removal

(doors taller than 8')

Ensamblaje del marco, instalación y extracción

(para puertas de más de 8')

for Andersen® A-Series 2-Panel, 3-Panel and 4-Panel Gliding Patio Doors and A-Series 2-Panel, 3-Panel

and4-Panel Gliding Patio Doors with Stormwatch® Protection

para puertas corredizas para patio de 2 paneles, 3 paneles y 4 paneles de la serie A de Andersen® y puertas

corredizas para patio de 2 paneles, 3 paneles y 4 paneles de la serie A con protección Stormwatch®

Parts Included / Partes incluidas

Operating Panel Carton Contains:

La caja de cartón del panel operativo

contiene lo siguiente:

(1-2) Operating Panel / Panel operativo

Stationary Panel Carton Contains:

La caja de cartón del panel estacionario

contiene lo siguiente:

(1-2) Stationary Panel / Panel estacionario

(1) Instruction Guide / Guía de instrucciones

Astragal Carton Contains (4-Panel Door Only):

La caja de cartón del Astrágalo contiene lo siguiente

(Sólo para puertas de 4 paneles ):

(1) Astragal /Astrágalo

(1) Astragal Fastener Pack /

Paquete del sujetador del astrágalo

(1) Astragal Fastener Cover Plug Pack

Paquete del tapón de la cubierta del sujetador del

astrágalo

Read these instructions before starting procedure. For additional information visit www.andersenwindows.com. For questions call 1-888-888-7020.

Lea estas instrucciones antes de iniciar el procedimiento. Para obtener información adicional, visite www.andersenwindows.com

Si tiene alguna pregunta, llame al 1-888-888-7020.

9117015 BB Revised 01/25/23

Tools Needed / Herramientas necesarias

• Safety glasses / Gafas de seguridad

• Phillips Screwdriver / Destornillador Phillips

• Drill/Driver / Taladro/Destornillador

• Caulk Gun / Pistola para calafatear

• 7/32 Hex Key / 7/32 Llave hexagonal

• Stiff Blade Putty Knife or Flat Pry Bar /

Espátula de hoja rígida o palanca plana

• Tape / Cinta

▶Parts included may exceed quantity required for your particular installation.

Las partes que se incluyen pueden exceder la cantidad requerida para su instalación en particular.

▶Do not remove packing clips from door until instructed.

No retire los sujetadores de embalaje de la puerta hasta que se le indique.

Operating Panel

Panel operativo

Stationary Panel

Panel estacionario

or/o bien

Astragal

Astrágalo

0 0 11

2-Panel Door

Puerta de 2

paneles

3-Panel Door

Puerta de 3

paneles

4-Panel Door

Puerta de 4

paneles

Astragal Fastener Plugs

Tapones del sujetador

del astrágalo

Astragal Fastener Cover Plug Pack

Paquete del tapón de la cubierta

del sujetador del astrágalo

0 0 7

2-Panel Door

Puerta de 2

paneles

3-Panel Door

Puerta de 3

paneles

4-Panel Door

Puerta de 4

paneles

#10 x 1-1/2" Pan Head Screws

(Astragal Screw Pack)

Tornillos de cabeza plana No. 10 x 1-1/2"

(Paquete de tornillos del astrágalo)

Astragal Fastener Pack

Paquete del sujetador

del astrágalo

9117015

Parts used for panel assembly that are included in frame carton:

Las partes que se utilizan en el ensamblaje del panel y que se incluyen en la caja de cartón del marco son las siguientes:

BAG

1 2 2

2 2 2

9 18 0

0 0 8

2-Panel Door

Puerta de 2

paneles

3-Panel Door

Puerta de 3

paneles

4-Panel Door

Puerta de 4

paneles

Interlock Weatherstrip

Head Dust Pad

Almohadilla antipolvo

para el cabezal del

burlete de enganche

Security Bracket

Dust Pad

Almohadilla antipolvo

para el soporte de

seguridad

Security Bracket

Soporte de seguridad

Filler Cap

Tapón de

relleno

(one left-hand, one right-hand)

(una para el lado izquierdo, una

para el lado derecho)

Fastener Plug

Tapón del sujetador

30 60 60

2 4 4

6 12 21

0 0 3

#7 x 5/8" White, Gray or Black Screws

Tornillos de cabeza plana No. 7 x 5/8" de color

blanco, gris o negro

#10 x 1" Stainless Steel Screws

Tornillos de acero inoxidable No. 10 x 1"

#10 x 3" Gray Screws

Tornillos No. 10 x 3" de color gris

#10 x 3" Stainless Steel Screws

Tornillos de acero inoxidable No. 10 x 3"

Panel Installation Pack

Paquete de instalación

del panel

Black Plug

Tapón negro

Washer

Arandela

(0-2) Stationary

Jamb Trim

Contramarco de

jamba esta cionaria

(1-2) Stationary

Panel Interlock

Weatherstrip

Burlete de

enganche del

panel estacionario

(1) Tube Silicone

Silicona en tubo

(1-2) Operating

Panel Interlock

Weatherstrip

Burlete de

enganche del

panel operativo

(1-2) Operating

Panel Stiffener

(veneered)

Refuerzo del

panel operativo

(enchapado)

(1-2) Stationary

Panel Stiffener

(painted)

Refuerzo del

panel estacionario

(pintado)

(1-2) Exterior Stiffener Pack

Paquete del refuerzo

exterior

6 12 12

2 4 4

1 2 2

2-Panel Door

Puerta de 2

paneles

3-Panel Door

Puerta de 3

paneles

4-Panel Door

Puerta de 4

paneles

Stiffener Brackets

(9021935)

Soportes del refuerzo

(9021935)

Stiffener Brackets

(9021936)

Soportes del refuerzo

(9021936)

#10 x 2" Oval Head Screws

Tornillos de cabeza ovalada No. 10 x 2"

(color interior)

#10 x 7/8" Stainless Steel Screws

Tornillos de acero inoxidable No. 10 x 7/8"

#10 x 2-1/2" Stainless Steel Screws

Tornillos de acero inoxidable No. 10 x 2-1/2"

11 22 22

Exterior Stiffener Fastener Plugs

Tapones del sujetador del refuerzo exterior

6 12 12

2-Panel Door

Puerta de 2

paneles

3-Panel Door

Puerta de 3

paneles

4-Panel Door

Puerta de 4

paneles

(1-2) Interior Stiffener Pack

Paquete del refuerzo interior

#10 x 2" Oval Head Screws

Tornillos de cabeza ovalada No. 10 x 2"

(color interior)

Interior Stiffener Fastener Plugs

Tapones del sujetador del refuerzo interior 11 22 22

9117015

Parts used for panel assembly that are included in frame carton: (Continued)

Las partes que se utilizan en el ensamblaje del panel y que se incluyen en la caja de cartón del

marco son las siguientes Continued:

(1) Receiver

Position

Template

Plantilla de

posición del

receptor

(1) Receiver

Receptor

(1) Lock

Cerrojo

(1) Bezel

Bisel

(1) Receiver

Position

Template

Plantilla de

posición del

receptor

(1) Receiver

Receptor

(1) Lock

Cerrojo

(1) Bezel

Bisel

2- and 3-Panel Door / Puerta de 2 y 3 paneles

(4) #8-32 x 7/8" Machine Screw

Tornillos para metales No. 8-32 x 7/8"

(2) #10 x 3" Security Screw

Tornillo de seguridad

n.º 10 x 3"

(1) Lock

Cerrojo (1) 2- or 3-Panel Receiver

Receptor de 2 o 3

paneles

(1) Lock

Cerrojo

(1) 4-Panel Door Receiver

Receptor para puerta

de 4 paneles

4-Panel Hardware Pack /

Paquetes de herrajes para 4 paneles

2- or 3-Panel Hardware Pack

(one pack for 2-panel doors, two packs for 3-panel doors)

Paquetes de herrajes para 2 o 3 paneles

(un paquete para puerta de 2 paneles; dos paquetes para

puerta de 3 paneles)

2- or 3-Panel Hardware Pack

(one pack for 2-panel doors, two packs for 3-panel doors)

Paquetes de herrajes para 2 o 3 paneles

(un paquete para puerta de 2 paneles; dos paquetes para

puerta de 3 paneles)

4-Panel Hardware Pack /

Paquetes de herrajes para 4 paneles

(5) #10 x 3" Stainless Steel Screw

Tornillo de acero inoxidable No. 10 x 3"

or/

o bien

or/

o bien

(2) #10 x 3" Stainless Steel Screw

Tornillo de acero inoxidable No. 10 x 3"

(1) #10 x 4" Security Screw

Tornillo de seguridad n.º 10 x 4"

(2) #10-32 x 1-1/4" Machine Screw

Tornillo para metales No. 10-32 x 1-1/4"

4-Panel Door / Puerta de 4 paneles

For Flush Mount Hardware/

Para herrajes de montaje embutido

For Reachout Lock Hardware/

Para herrajes de cerrojo de alcance

For Flush Mount Hardware/

Para herrajes de montaje embutido

For Reachout Lock Hardware/

Para herrajes de cerrojo de alcance

9117015

DraftDraft

Procedure and

Product Information

IMPORTANT

Important Safety and

Product Information

for Andersen® Windows and Doors

This is the Safety Alert Symbol used to alert you to

potential injury hazards. Obey all safety messages that

follow this symbol to avoid possible injury or death.

Signal Word and Consequence

Major Injury/Death

WARNING

COULD

Result in: Minor Injury

CAUTION

COULD

Result in:

Product or Property

Damage

NOTICE

COULD

Result in:

· Leave this installation instruction with the home/building owner.

· For additional support or help please go to: andersenwindows.com and visit our Help Center.

· To congure installation instructions go to: andersenwindows.com/installation

Handling Installation

· Use caution when working at elevated heights and

around window and door openings. Follow the

manufacturers’ instructions for ladders and scaffolding.

Failure to do so could result in injury or death.

· Support window or door in opening at all times until

fully fastened. Failure to do so could result in window or

door falling out causing injury, property or product

damage.

· Windows and doors have small parts (e.g. hole plugs,

operator spline caps, fasteners, etc.). Small parts if

swallowed could pose a choking hazard to young

children. Dispose of unused, loose, or easily removed

small parts. Failure to do so could result in injury.

· Windows and doors can be heavy. Use safe lifting

techniques and a reasonable number of people with

enough strength to lift, carry, and install window and

door products. Heavier windows and doors will require

mechanical assistance. Failure to do so could result in

injury, product or property damage.

· DO NOT lift or carry window or door by the exterior

trim or extension jambs. Doing so could result in injury,

product or property damage.

· Windows, doors, and installation components can

have sharp edges. Wear protective equipment when

handling. Failure to do so could result in injury.

· DO NOT drag, rock, cartwheel, or walk windows,

doors, sash, or panels across the floor. Doing so could

result in product or property damage.

Tools

· Follow manufacturers’ instructions for hand and power tools. Always wear safety glasses. Failure to do so could result in

injury, product or property damage.

❚ Tools

❚ Handling

❚ Installation

❚ Sealing

❚ Fastening

❚ Finishing

Safety and Product Information Index

❚ Glass

❚ Protective Film

❚ Cleaning

❚ Use/Operation

❚ Joining

❚ Product Information

Read this Important Safety and Product

Information completely before starting.

WARNING

WARNING WARNING

▶Para obtener la versión en español de Información importante sobre productos y seguridad, visite: andersenwindows.com

9117015

DraftDraft

NOTICE

· Andersen head ashing and installation anges DO

NOT take the place of window and door ashing tape or

liquid ashing. Window or door must be properly ashed

and sealed with a material compatible sealant for

protection against water and air inltration.

Failure to do

so could result in product or property damage.

· DO NOT set window or door directly on installation

ange. Doing so could affect product performance, and

could result in product or property damage.

· DO NOT set window directly on sill plate. Elevate

window with shims under the side jambs. Failure to do

so could affect operation and product performance, and

could result in product damage.

· Window or door must be properly shimmed. Failure to

do so could affect operation and product performance,

and could result in product damage.

· A continuous full perimeter interior seal between

window or door frame and opening is required. Failure to

do so will affect product performance, and could result

in product or property damage.

· Protect window and door sills during installation and

throughout construction. Failure to do so could result in

product damage.

· DO NOT remove window or door packaging material until

instructed to do so. Doing so could result in product damage.

Installation (Continued)

NOTICE

· Use masonry screws when fastening directly into

masonry or through a buck into masonry. Failure to do

so could affect product performance, and could result in

product or property damage.

· DO NOT over drive screws or nails. Doing so could

result in product damage.

· Fasteners must be attached to a structural framing

member. Failure to do so will reduce the structural

performance to less than published values and could

affect product performance, and could result in product

or property damage.

Fastening

· Metal fasteners and components could corrode when

exposed to preservative-treated or fire-retardant treated

lumber. Use approved fasteners and components to

fasten window or door. Failure to do so could cause a

failure resulting in injury, product or property damage.

· Fastener must attach to a structural framing member

with a 1-1/2" minimum fastener embedment. Failure to

do so could result in injury, product or property damage.

· DO NOT remove screws that attach installation clips or

gusset plates to window or door frames. Doing so could

result in injury, product or property damage.

Sealing

NOTICE

CAUTION

· Follow instructions of foam, sealant, and flashing

manufacturers regarding safety, material application,

compatibility, and periodic maintenance for continued

weather resistance of their products. Failure to do so

could result in injury, product or property damage.

Finishing

NOTICE

· DO NOT stain or paint weatherstrip, vinyl, glass, or

hardware. Doing so could result in product damage.

· Read and follow nish manufacturer's instructions and

safety information. Failure to do so could result in

product damage.

· DO NOT over load brush with stain or paint when

nishing. Doing so could allow nish to wick between

glass stop or grille, and glass.

WARNING

· Clean and prepare surfaces receiving sealant following

sealant manufacturer's instructions. Failure to do so could

result in water inltration causing product or property damage.

· DO NOT use abrasive cleaners or solvents when

cleaning Fibrex® material. Doing so could result in

product damage. Go to andersenwindows.com for a list

of recommended cleaners.

9117015

DraftDraft

NOTICE

Glass

· Unless specifically ordered, Andersen windows are not

equipped with safety glass, and if broken, could

fragment causing injury. Many laws and building codes

require safety glass in locations adjacent to or near

doors. Andersen windows are available with safety glass

that could reduce the likelihood of injury when broken.

Information on safety glass is available from your local

Andersen dealer.

· Tempered or laminated safety glass is not standard for

windows and must be special ordered. Check local

building codes for required locations. Failure to do so

could result in injury, product or property damage.

· DO NOT place suction grips over film

seams on glass. Suction grips will not

hold if placed over lm seam to lift or

move window or door. Window or door

will fall and could result in injury,

product or property damage.

· DO NOT remove any

protective film near

flammable materials.

Static charge created

when removing film

can ignite flammable

materials or cause a

shock. Doing so could result in injury, product or

property damage. See warning label on glass.

· Dispose of protective film immediately after

removing. Failure to do so could pose a suffocation

hazard to children.

NOTICE

· DO NOT remove protective lm from glass until after

construction is completed. Doing so could allow glass to

be damaged.

· Remove protective film from non-glass components

immediately after installation. Failure to do so could

result in product damage.

NOTICE

Cleaning

Protective FilmFinishing (Continued)

· Finish all wood surfaces immediately after

installation. Unnished wood will deteriorate, discolor,

and could bow or split. Some

surfaces are hidden from view.

· Some products are shipped

unassembled, and it may be

more convenient to finish

wood surfaces for these

products prior to

assembly and

installation.

WARNING

· Acid solutions used for cleaning masonry or concrete

will damage all components of window or doors. Protect

window or door and follow cleaning product

manufacturer's instructions. If acid contacts window or

door, wash all surfaces immediately with clean water.

· DO NOT use or apply solvents, abrasives, harsh

chemicals or cleaners to window or door components.

Doing so will result in product damage.

For a list of recommended cleaners go

to: andersenwindows.com

· DO NOT use metal razor blades to

clean glass surface. Glass damage

could result.

· DO NOT apply any type of film to insulating glass.

Doing so could cause thermal stress conditions and

result in glass damage. Shading devices (e.g. insulated

coverings, shutters, etc.) could also cause thermal

stress and condensation causing deterioration of

windows or doors.

· DO NOT use sealants on exterior or

interior glass surface.

NOTICE

9117015

DraftDraft

Joining

IMPORTANT

· Buildings constructed prior to 1978 could contain lead

paint which could be disturbed during window or door

replacement. For more information on proper management

of lead paint, go to: www.epa.gov/lead

· Instructions may not be right for all installations due to

building design, construction materials, or methods used

and/or building or site conditions. Consult a contractor or

architect for recommendations.

· Installation flanges may need to be removed for some

installations. (e.g. masonry, replacement), or where exterior

finish is already applied (e.g. siding, brick veneer, stucco).

· Installation ange on the window or door alone will not

properly ash and seal the window or door.

· DO NOT remove band, plastic ties, or packing clips from

window or door until instructed.

· DO NOT remove performance (NFRC) label until after nal

inspection. Doing so could delay nal inspection and

sign-off by the code ofcial.

· Check with your local building code ofcial to identify and

conrm compliance with local building code requirements.

· Contact local authorities or waste management company

for proper recycling and disposal instructions for removed

window or door.

· For cleaning instructions for window and door components

go to: andersenwindows.com.

· During construction protect products from construction

debris, harsh chemical such as brick wash, roof runoff, and

cement/masonry which can cause damage to window and

door products.

· Protective lm is not present on all windows or doors.

Protective lm is not a substitute for masking.

· Remove protective film from glass within six (6) months of

installation and when temperature is above 32° F.

· Remove protective lm by peeling from seam or corner.

Use a plastic scraper to start if needed.

· Extension jambs can be factory applied on some windows

or eld applied prior to installation. DO NOT apply extension

jambs prior to window or door installation that will be

fastened with installation clips. Doing so could prevent

access to installation clips for fastening.

· For extension jamb application refer to

instructions included with part(s) or go to:

andersenwindows.com

· Use painters masking tape for protecting

products during construction. Avoid using

duct or packaging tapes.

Use/Operation

· DO NOT stand in front of or near windows or doors

during a storm. Doing so could result in injury.

Accessories such as grilles, art glass, and insect

screens could dislodge and become airborne if window

or door is impacted by wind-borne debris from severe

storms or hurricane strength winds. In the event of a

storm, remove all accessories from windows or doors

and move to a safe location.

· DO NOT install air conditioner in

window. Doing so could result in

injury, product or property damage.

· Wind load brackets

must be flipped out

when not tilting or

cleaning. If wind load

brackets are not flipped

out, window could blow

in resulting in potential

injury and/or product

damage.

· DO NOT attach objects or accessories to window or

door except Andersen® products specifically designed

for the window or door. Doing so could result in injury,

product or property damage.

Product and General Information

· DO NOT join any window or door, horizontally or

vertically, to any window or door not designed for

joining. Doing so could result in injury, product or

property damage.

· Joined windows or doors must be individually

supported in the opening. Failure to do so could affect

operation and product performance, and could result in

product or property damage.

CAUTION

WARNING

Flipped Out Flipped In

Exterior

9117015

Panel Alignment Sticker

Etiqueta de alineación

del panel

Stationary Panel

Panel estacionario

▶For panel removal, go to page 29.

▶Para la extracción del panel, consulte la página 29.

4-Panel Door / Puerta de 4 paneles

Position stationary panel into head jamb from the exterior. Align notches on bottom of panel with sill guides and swing/push panel onto sill.

Desde el exterior, posicione el panel estacionario dentro de la jamba de cabecera. Alinee las muescas en la parte inferior del panel con las guías del

riel y gire/empuje el panel sobre el riel. Deslice los paneles tal como se muestra.

Right Hand

Stationary Panel

Panel estacionario

derecho

Left Hand

Stationary Panel

Panel estacionario

izquierdo

Suction grips will not hold if placed over

seam of lm to lift or move unit. Unit will

fall causing damage or injury.

Las ventosas no funcionarán si se

colocan sobre la costura de la película al

levantar o mover la unidad. La unidad se

caerá y provocará daños y lesiones.

Do not set or move panels on corners.

Doing so will result in product damage.

No coloque ni mueva los paneles de las

esquinas. De lo contrario, el producto

se dañará.

Suction Cup

Ventosa

Film Seam

Costura de

la pelicula

Windows and doors can be heavy. Use

safe lifting techniques and a reasonable

number of people with enough strength

to lift, carry and install window and door

products to avoid injury and/or product

damage.

Las puertas y las ventanas pueden ser

pesadas. Utilice técnicas seguras de

levantamiento de peso y un número

razonable de personas con suciente

fuerza para levantar, cargar e instalar los

productos de puertas y ventanas, a n de

evitar lesiones y/o daños al producto.

3-Panel Door / Puerta de 3 paneles

2-Panel Door / Puerta de 2 paneles

View of panel

alignment sticker.

Vista de la etiqueta

de alineación del

panel.

WARNING / ADVERTENCIA WARNING / ADVERTENCIA CAUTION / PRECAUCIÓN

9117015

Exterior

2-Panel Door / Puerta de 2 paneles

3-Panel Door / Puerta de 3 paneles

4-Panel Door / Puerta de 4 paneles

Correct

(in bracket)

Correcto

(en soporte)

Incorrect

(below bracket)

Incorrecto

(debajo del

soporte)

Slide panels as shown. An audible click is heard when panel retainers lock ush into bracket. Pull on panel to make sure panel retainer is engaged.

Deslice los paneles tal como se muestra. Cuando los dispositivos de retención del panel enganchan a ras en el soporte, se debe escuchar un clic.

Tire del panel para asegurarse de que el dispositivo de retención del panel esté enganchado.

Panel Retainer

Dispositivo de

retención del panel

Flush

A ras

1/2 Engaged

Acople medio

Slide toward jamb. Push

at center of panel to

prevent binding.

Deslice hacia la jamba.

Empuje desde el centro

del panel para evitar

que se atasque.

Slide toward jamb

Deslice hacia la jamba

Slide toward jamb

Deslice hacia la jamba

Slide left

(as viewed from exterior)

Lateral izquierdo

(visto desde el exterior)

Fully Engaged

Acople completo

Bracket

Soporte

Interior

9117015

Attach stationary panel ller cap.

Coloque el tapón de relleno del panel estacionario.

Stationary Panel Filler Cap

Tapón de relleno del panel

estacionario

Interior

Remove release liner. Position black plug on stationary panel ush with

panel edge and tight to head.

Retire el papel antiadherente Coloque el tapón negro en el panel

estacionario a ras con el borde del panel y ajuste a la cabecera.

Black Plug

Tapón negro

Release

Liner

Papel

antiadherente

Flush with

panel edge.

A ras con el

borde del

panel

Tight to head.

Ajuste a la

cabecera

Head

Cabecera

Panel

9117015

Head Jamb / Jamba de cabecera

Black Plug

Tapón negro

1/16" Bit

Broca de 1/16"

#7 x 5/8"

Screws

Tornillos

No. 7 x 5/8"

Stationary Panel

Interlock

Weatherstrip

Burlete de

enganche del

panel

estacionario

Drill / Driver

Taladro / Destornillador

Stationary Panel

Filler Cap

Tapón de relleno

del panel

estacionario

Interior

Position stationary panel interlock weatherstrip tight to stationary panel ller cap at bottom and ex into black plug at head jamb. Drill 1/16" holes,

3/8" deep using interlock weatherstrip as a guide and fasten using painted #7 x 5/8" screws.

Coloque el burlete de enganche del panel estacionario bien rme contra el tapón de relleno del panel estacionario en la parte inferior y dóblelo hacia

adentro del tapón negro en la jamba de cabecera. Taladre oricios de 3/8 pulgadas de profundidad con una broca de 1/16 pulgadas y utilice el

burlete de enganche como guía; ajuste con tornillos pintados nº 7 x 5/8 pulgadas.

Stationary Panel Interlock Weatherstrip

Burlete de enganche del panel estacionario Sill / Riel

Stationary Panel Interlock Weatherstrip

Burlete de enganche del panel estacionario

Make sure interlock

weatherstrip ts tight to

panel.

Asegúrese de que el

burlete de enganche se

ajuste bien al panel.

Interior

9117015

Apply silicone to stationary panel and jamb corner at end of

weatherstrip.

Aplique silicona al panel estacionario y a la esquina de la jamba en el

extremo del burlete.

2- and 4-Panel Doors Only / Sólo puertas de 2 y 4 paneles

Reverse angles shown

Se muestran los ángulos traseros

Backing

Lámina

protectora

Apply silicone along bottom of stationary panel interlock weatherstrip and ll security bracket rout with silicone. Slide security bracket into place and

secure using two #10 x 1" stainless steel screws.

Aplique silicona a lo largo de la parte inferior del burlete de enganche del panel estacionario y rellene la guía del soporte de seguridad con silicona.

Deslice el soporte de seguridad en su lugar y ajuste con dos tornillos nº 10 x 1 pulgadas de acero inoxidable.

Stationary Panel Interlock Weatherstrip

Burlete de enganche del panel estacionario

Remove backing and attach security bracket dust pad next to security

bracket.

Retire la lámina protectora y coloque la almohadilla antipolvo para el

soporte de seguridad al lado de este.

Security Bracket

Dust Pad

Almohadilla

antipolvo para

el soporte de

seguridad

Security Bracket

Dust Pad

Almohadilla antipolvo para el

soporte de seguridad

Weatherstrip

Burlete

Security Bracket

Soporte de seguridad

#10 x 1" Stainless

Steel Screws

Tornillos de acero

inoxidable nº 10 x 1

pulgada

Security Bracket

Soporte de

seguridad

Silicone

Silicona

Caulk Gun

Pistola para

calafatear

9117015

Exterior

Position operating panel interlock weatherstrip tight to dust pad. Drill 1/16" holes, 3/8" deep using interlock weatherstrip as a guide and fasten using

painted #7 x 5/8" screws.

Coloque el burlete de enganche del panel operativo bien rme con la almohadilla antipolvo. Taladre oricios de 3/8 pulgadas de profundidad con

una broca de 1/16 pulgadas y utilice el burlete de enganche como guía; ajuste con tornillos pintados nº 7 x 5/8 pulgadas.

Remove backing and attach interlock weatherstrip head dust pad above

operating panel interlock weatherstrip.

Retire la lámina protectora y coloque la almohadilla para el cabezal

antipolvo del burlete de enganche arriba del burlete de enganche del

panel operativo.

Operating Panel Interlock

Weatherstrip

Burlete de enganche del panel

operativo

Dust Pad

Almohadilla para polvo

#7 x 5/8" Screws

Tornillos No. 7 x 5/8"

1/16" Bit

Broca de 1/16"

Operating Panel

Interlock Weatherstrip

Panel operativo

Burlete de enganche

Interlock

Weatherstrip

Head Dust Pad

Almohadilla

antipolvo para

el cabezal del

burlete de

enganche

Interior

Position panel rollers on sill track and tip into frame. Slide panel closed.

Coloque los rodillos del panel en la guía del riel e incline el panel dentro del marco. Deslice el panel cerrado.

Insert end of head stop into operating side jamb and rotate into position.

Verify holes in head stop align with predrilled holes in head jamb.

Coloque el extremo del tope de cabecera dentro de la jamba lateral

operativa y gírela en posición. Verique que los oricios del tope de cabecera

estén alineados con los oricios pretaladrados de la jamba de cabecera.

Panel Bumper

Tope del panel

Head Stop

Tope de cabecera

Watershed

Cuenca

Operating Panel

Head Stop

Tope de cabecera

9117015

Aluminum portion

of head stop must

contact side jamb on

the operating panel

side of unit.

La parte de aluminio

del tope de cabecera

debe hacer contacto

con la jamba

lateral del lado del

panel operativo de

launidad.

Fasten through holes

along ridge in head stop.

Ajuste a través de los

orificios a lo largo de la

saliente en el tope de

cabecera.

Do not fasten through larger

holes located toward exterior.

No ajuste a través de orificios

más grandes que estén ubicados

hacia el exterior.

Do not apply panel weight

on edge of watershed.

No aplique el peso del panel

en el borde de la cuenca.

Fasten head stop and bumper(s) using screws removed previously

during frame assembly.

Ajuste el tope de cabecera y el/los reborde(s) con tornillos retirados

previamente durante el ensamblaje del marco.

Support panel in frame at all times until secured in next step. Failure to do so

may result in panel falling out causing injury, property, and/or product damage.

Sostenga el panel en el marco todo el tiempo, hasta que se asegure en el

siguiente paso. De no hacerlo, el panel se puede caer y provocar lesiones, daños

al producto y/o a la propiedad.

Watershed

Cuenca

Do not apply panel

weight on edge of

watershed.

No aplique el peso

del panel en el borde

de la cuenca.

WARNING / ADVERTENCIA NOTICE / AVISO

9117015

Washer and #10 x 3"

Gray Screws

(above operating

panel(s))

Arandela y tornillos

nº 10 x 3 pulgadas

de color gris

encima de los paneles

operativos

Interior

Open operating panel(s) and secure at head.

Abra el panel o paneles de mando y fíjelos en la parte superior.

#10 x 3" Gray Screws

Tornillos n° 10 x 3

pulgadas de color gris

Interior

Shim behind each fastener hole at head. Shims must be tight to

installation ange, recessed 3/8".

Coloque cuñas detrás de cada oricio del sujetador en la

cabecera. Las cuñas deben ajustarse a la brida de instalación y

empotrarse unos 3/8 pulgadas.

Shim tight to

installation flange.

Ajuste la cuña

a la brida de

instalación.

Installation Flange

Brida de instalación

Recessed 3/8"

3/8 pulgadas

empotrados

Shim

Cuña

Interior

Secure through head support bracket.

Asegure a través del soporte de apoyo de cabecera.

4-Panel Doors Only / Sólo para puertas de 4 paneles

#10 x 3" Stainless Steel Screws

Tornillos de acero inoxidable No. 10 x 3"

Head Support Bracket

Soporte de apoyo de cabecera

9117015

(shown from exterior)

(se muestra desde el exterior)

Position astragal on edge of operating door panel, as shown, with veneer to the interior. Align astragal ush with top and bottom of panel, with exterior

side tight to door panel. Drill 1/8 holes, 1-1/2" deep, using astragal as a guide and fasten using #10x1-1/2" pan head screws. Apply astragal

fastener plugs at screw locations.

Coloque el astrágalo en el borde del panel operativo de la puerta, tal como se muestra, con la chapa hacia el interior. Alinee el astrágalo al ras con

la parte superior e inferior del panel, con el lateral exterior rme contra el panel de la puerta. Taladre oricios de 1-1/2 pulgadas de profundidad con

una broca de 1/8 pulgadas y utilice el astrágalo como guía; ajuste con tornillos de cabeza plana nº 10x 1-1/2 pulgadas. Coloque los tapones del

sujetador del astrágalo en las ubicaciones de los tornillos.

Operating Door Panel

Panel operativo de la

puerta

Operating Door Panel

Panel operativo de la puerta

(shown not installed)

(Se muestra no instalado)

9117015

Exterior

Panel Astragal

Astrágalo del panel

4-Panel Door Only / Sólo para puerta de 4 paneles

1/8" Drill Bit

Broca para taladro

de 1/8"

#10 x 1-1/2" Pan

Head Screws

Tornillos de cabeza

plana

No. 10 x 1-1/2"

Astragal Fastener Plugs

Tapones del sujetador

del astrágalo

Astragal flush with top of panel.

Astrágalo al ras con la parte

superior del panel.

Astragal fastener plugs are small parts and,

if swallowed, could pose a choking hazard

to young children. Remove and dispose

of any loose or easily removed astragal

fastener plugs.

Los tapones del sujetador del astrágalo son

partes pequeñas que, en caso de ingesta,

pueden representar un riesgo de asxia

para niños pequeños. Retire y deseche

todos los tapones del sujetador del

astrágalo sueltos o que se puedan quitar

fácilmente.

WARNING / ADVERTENCIA

9117015

Position stationary panel stiffener on stationary panel edge and fasten through all holes using #10 x 2" oval head screws. Apply fastener plugs at all

hole locations on stationary panel stiffeners.

Coloque el refuerzo del panel estacionario en el borde del panel estacionario y ajuste a través de todos los oricios. Para ello, utilice tornillos de

cabeza ovalada nº 10 x 2 pulgadas. Aplique tapones del sujetador en todas las ubicaciones de oricios sobre los refuerzos del panel estacionario.

Stationary Panel

Panel estacionario

Position head and sill brackets against edge of stationary panel as shown. Fasten upper bracket using two #10 x 2-1/2" stainless steel screws and

lower bracket using two #10 x 7/8" stainless steel screws.

Coloque los soportes de cabecera y de riel contra el borde del panel estacionario, tal como se muestra. Ajuste el soporte superior. Para ello, utilice

dos tornillos de acero inoxidable nº 10 x 2-1/2 pulgadas y para el soporte inferior utilice dos tornillos nº 10 x 7/8 pulgadas.

Exterior

Fastener plugs are small parts and, if swallowed, could

pose a choking hazard to young children. Remove and

dispose of any loose or easily removed fastener hole

plugs.

Los tapones del sujetador son partes pequeñas que, en

caso de ingesta, pueden representar un riesgo de asxia

para niños pequeños. Retire y deseche todos los

tapones para oricios del sujetador sueltos o que se

puedan quitar fácilmente.

WARNING / ADVERTENCIA

Head Bracket

Soporte de

cabecera

Sill Bracket

Soporte del riel

Position leg of

head bracket,

as shown.

Coloque la

pata del

soporte de

cabecera,

tal como se

muestra.

Position leg

of sill bracket,

as shown.

Coloque la pata

del soporte del

riel, tal como se

muestra.

#10 x 2-1/2"

Stainless Steel

Screw

Tornillo de acero

inoxidable

No. 10 x 2-1/2"

#10 x 7/8"

Stainless Steel

Screw

Tornillo de acero

inoxidable

No. 10 x 7/8"

#10 x 2" Oval Head Screw

Tornillo de cabeza ovalada

nº 10 x 2 pulgadas

Stationary Panel

Stiffener

Refuerzo del panel

estacionario

Fastener Plug

Tapón del sujetador

Fastener Plug

Tapón del sujetador

Interior

9117015

Position operating panel stiffener against operating panel edge, over interlock weatherstrip, ush with bottom edge of door. Fasten stiffener using

#10 x 2" oval head screws through pre-drilled holes. Apply fastener plugs at all hole locations on operating panel stiffeners.

Coloque el refuerzo del panel operativo contra el borde del panel operativo, sobre el burlete de enganche, al ras del borde inferior de la puerta. Ajuste

el refuerzo con tornillos de cabeza ovalada n° 10 x 2 pulgadas a través de los oricios pretaladrados. Aplique tapones del sujetador en todas las

ubicaciones de oricios sobre los refuerzos del panel operativo.

#10 x 2" Oval

Head Screws

Tornillos de cabeza

ovalada nº10 x 2

pulgadas

Operating Panel Stiffener

Refuerzo del panel operativo

Interior

Equal gap between

panel and side jamb

Igual espacio entre el

panel y la jamba lateral

Open operating panel slightly. Remove adjustment hole caps. Insert at blade screwdriver into sockets and turn clockwise to raise panel or

counterclockwise to lower panel until gap is equal full length. Replace adjustment hole caps.

Abra ligeramente el panel operativo. Retire los tapones de oricios de ajuste. Coloque un destornillador de punta plana dentro del adaptador y

gire hacia la derecha para levantar el panel o hacia la izquierda para bajar el panel hasta que el espacio sea igual en todo el largo. Retire las

tapas para oricios de ajuste.

Raise

Para

levantar

Lower

Para bajar

Flat Blade Screwdriver

Destornillador de punta

plana

Adjustment Hole Cap

Replace when

adjustment is

complete.

Tapón para

oricio de ajuste

Vuelva a colocarlo

cuando el ajuste esté

completo.

Interior

Insert lock in operating panel with lock button on top.

Introduzca el cerrojo en el panel operativo con el botón del cerrojo en

la parte superior.

Operating Panel

Panel operativo

Lock Button on top

Botón del cerrojo

Lock

Cerrojo

Lock Button on top

Botón del cerrojo

9117015

#10 x 3"

Stainless

Steel Screws

Tornillo de

acero

inoxidable

No. 10 x 3"

Adjustment hole caps are small parts. And if swallowed, could pose a choking hazard to young children. Remove and dispose of any

loose or easily removed adjustment hole caps. Replace adjustment hole caps after making adjustments.

Las tapas para oricios de ajuste son partes pequeñas que, en caso de ingesta, pueden representar un riesgo de asxia para niños

pequeños. Retire y deseche todas las tapas sueltas o que se puedan quitar fácilmente. Vuelva a colocar los tapones después de

realizar los ajustes.

WARNING / ADVERTENCIA

or/

o bien

Lock

Cerrojo

For Flush Mount Hardware/

Para herrajes de montaje embutido

For Reachout Lock Hardware/

Para herrajes de cerrojo de alcance

Insert lock in operating panel with lock button on top and fasten

using two (2) #10 x 3" stainless steel screws.

Introduzca el cerrojo en el panel operativo con el botón del cerrojo

en la parte superior y fíjelo con dos (2) tornillo de acero inoxidable

No. 10 x 3"

Page is loading ...

Andersen Panel Assumbly Installation guide

Brand: Andersen

Model: Panel Assumbly

Type: Installation guide

Download PDF

report

in other languages

español: Andersen Panel Assumbly Guía de instalación

Andersen Panel Assumbly Installation guide

Andersen Panel Assumbly Installation guide

in other languages

Related papers

Other documents