Page is loading ...
1
“Andersen” is a registered trademark of Andersen Corporation. All other marks where denoted are marks of Andersen Corporation. ©2006-2006 Andersen Corporation. All rights reserved.
Please read this guide completely before starting. For questions about this and other Andersen® products, call 1-888-888-7020.
For the most current version of this guide visit www.andersenwindows.com. Consult your local building code official for
applicable building codes and regulations. Thank you for choosing Andersen® products.
Please leave this information with homeowner.
A
B
C
D
E
F
G
Key
nHinge
n#10 x 3" Wood Screws
n#10 x 1-3/4" Wood Screws
n#10-32 x 3/4" Machine Screws (Jamb Hinge)
n#10-32 x 1/2" Machine Screws (Astragal Hinge)
Read and follow these warnings during installation.
Use caution when working at elevated
heights and around unit openings. Follow
manufacturer’s instructions for safe use of
ladder and/or scaffolding. Failure to do
so may result in injury or death.
Follow manufacturer’s instructions for safe
operation of hand/power tools. Always
wear safety glasses. Failure to do so may
result in injury and/or product damage.
for 200 Series Hinged Patio Doors - Inswing
0005428 BA Revised 05/03/06
A
B
C
D
E
F
Gn
A
Hinge Replacement & Hinge
and Hardware Adjustment Guide
Tools Needed
· Safety Glasses
· 5/32" Hex Wrench (Included with Unit)
· Flat Blade Screwdriver
· Phillips Screwdriver
• Wood Blocks
n
C
n
B
n
D
4For hinge replacement, begin at step 1.
4For hinge adjustment, begin at step 4.
Vertical Right Hand Hinge
(middle location)
Vertical Left Hand Hinge
(middle location)
Horizontal Hinge
(top and bottom location)
n
E
Limited Publication Release
Or Or
Parts Included
(replacement hinge kit)
· (1) Instruction Guide
· (1) Hinge
· (2) #10 x 3" Screws
· (4) #10 x 1-3/4" Screws
· (2) #10-32 x 3/4" Screws
· (2) #10-32 x 1/2" Screws
3
Interior
1
Interior
2
Interior
Identify active panel and open. Block door in full open position for hinge access and to keep
panel from shifting when removing middle hinge(s).
2
0005428
4-Hinge double
door shown in
this guide
except where
noted.
Wood Block
Do not remove more than one hinge at a time.
Removing all hinges could cause panel to
drop causing severe injury. Replace only one
hinge at a time.
Remove and replace top or bottom horizontal adjustment hinge, one at a time Or Remove and replace middle vertical adjustment
hinge(s), one at a time. Properly dispose of old hinges and screws.
Top or bottom horizontal
adjustment hinge
Top Horizontal
Adjustment Hinge
Middle
Vertical
Adjustment
Hinges
Middle vertical
adjustment hinge
Bottom Horizontal
Adjustment Hinge
Astragal
1-3/4"
Screws
3" Screws
1/2" (double door) or
3/4" (single door)
Machine Screws
1-3/4"
Screws
3" Screws
1/2" or 3/4"
Machine
Screws
Horizontal
Adjustment
Vertical
Adjustment
4
Interior
5
Interior
3
Hinge Jamb
Adjust panel for equal gap side to side (horizontal adjustment).
Turn top and bottom
hinges clockwise to
move panel toward
hinge jamb.
Turn top and
bottom hinges
counterclockwise to
move panel away
from hinge jamb.
Remove blocking. Check panel operation.
0005428
Horizontal Adjustment
Equal Gap at
Each Hinge
Equal Gap
Along Sides
Four hinge
single door
shown.
6
Interior
7
Interior
Turn middle
hinge(s) adjustment
screw toward (+) to
raise panel
Inspect from exterior for contact between panel and
weatherstrip. If necessary, adjust latch receiver tab to achieve
weatherstrip contact/compression using a flat blade screwdriver.
Adjust panel gap by turning middle hinge adjustment screw until gap at top equals side (vertical adjustment).
Vertical
Adjustment
4
0005428
Turn middle
hinge(s)
adjustment
screw toward (-)
to lower panel
Weatherstrip
Gap at top
equal to gap
at side
Installation is finished.
Four hinge
single door
shown.
Latch
Receiver
Tab
Flat Blade
Screwdriver
Tighten
Loosen
/