Andersen 9069158 Side Jamb Liner Replacement Service Instructions

Andersen
Brand
Andersen
Model
9069158 Side Jamb Liner Replacement
Type
Service Instructions

Andersen 9069158 Side Jamb Liner Replacement:

The Andersen 9069158 Side Jamb Liner Replacement is a genuine Andersen replacement part designed for use with E-Series double-hung windows. It is used to replace worn or damaged side jamb liners, which are essential for the proper operation of the window.

The replacement process is relatively straightforward and can be completed in a few simple steps. First, remove the existing side jamb liner by prying it away from the frame. Then, insert the new side jamb liner into the frame, making sure to lock the front lip behind the interior side stop. Finally, re-engage the side jamb liner by pressing the jamb liner edge into the frame.

Andersen 9069158 Side Jamb Liner Replacement:

The Andersen 9069158 Side Jamb Liner Replacement is a genuine Andersen replacement part designed for use with E-Series double-hung windows. It is used to replace worn or damaged side jamb liners, which are essential for the proper operation of the window.

The replacement process is relatively straightforward and can be completed in a few simple steps. First, remove the existing side jamb liner by prying it away from the frame. Then, insert the new side jamb liner into the frame, making sure to lock the front lip behind the interior side stop. Finally, re-engage the side jamb liner by pressing the jamb liner edge into the frame.

“Andersen” and all other marks where denoted are trademarks of Andersen Corporation and its subsidiary. ©2013 Andersen Corporation. All rights reserved. 9069158 BA Revised 06/03/13
Side Jamb Liner Replacement
for E-Series Double-Hung
Thank you for choosing Andersen.
For questions call 1-888-888-7020. For more information and/or guides visit www.eaglewindow.com
Please leave this guide with building owner.
▶Read guide from beginning to end before starting maintenance procedure. Read all warnings and cautions during unit maintenance.
Parts Included
(1) Side Jamb Liner
▶For information, calculating, and design pressure ratings for E-Series windows and doors go to
www.eaglewindow.com/Wintelligence/Design-Pressure-Estimator.aspx
▶Check with your local building code ofcial to identify and conrm compliance with local building code requirements.
Tools Needed
∙Safety Glasses
∙Flat Blade Screw Driver
∙Finish Nailer (for monumental units only)
∙Pliers (for monumental units only)
∙Putty Knife (for monumental units only)
Supplies Needed
∙Denatured Alcohol
∙Clean Cloth
Side Jamb Liner
Use caution when working at elevated
heights and around unit openings. Follow
manufacturers’ instructions for ladders and/
or scaffolding. Failure to do so may result in
injury or death.
Follow manufacturers’ instructions for hand
or power tools. Always wear safety glasses.
Failure to do so may result in injury and/or
product damage.
Windows and doors can be heavy. Use safe
lifting techniques and a reasonable number of
people with enough strength to lift, carry and
install window and door products to avoid injury
and/or product damage.
2
9069158
Slide tilt latches inward while tilting sash in
90 degrees.
Tilt
Latches
Tilt
Latch
Lower top sash 6”.
6 Inches
6
Interior
7
Interior
Pivot bottom sash to remove from window
frame as shown. Place sash on clean at work
surface, exterior side up.
Rotate and hold lock handles toward center
while tilting sash in 90 degrees.
Unlock window and raise bottom sash 4".
Lock
Handles
4 Inches
Lock
Handles
2
Interior
3
Interior
4
Interior
Bottom Sash
Bottom Sash
Pry interior side stop away from frame. Repeat on opposite side. Remove any nails from frame and
interior side stops.
Remove sash stop from the side jamb.
For Monumental Only
Single Hung and Monumental Only
▶For double hung units proceed to step 6.
1
Interior
▶For single and double hung units proceed to step 2.
5
Interior
Pliers
Interior Side Stop
Pivot top sash to remove from window frame
as shown. Place sash on clean at work
surface, exterior side up.
8
Interior
Top Sash
Putty Knife
Interior Side Stop
3
9069158
Slide outside side jamb liner insert up 12”.
12 Inches
Pocket Cover
Grasp jamb liner pocket cover at bottom and pull outward and down
from behind head stop to remove and save for reuse.
9
Interior
12
Interior
Outside Jamb Liner
Insert
Insert at blade screwdriver into cam slot, apply rm downward pressure, and rotate ¼ turn. Hold rmly allowing shoe to rise until it stops. Repeat for
other three balances.
Balance
Shoe
Shoe
Balance
Cam
Flat Blade
Screwdriver
Balance shoes are under
high tension. Use at blade
screwdriver with long handle
so that both hands can be
used to release balance
tension. Suddenly releasing
balance shoe could damage
window unit. Cam in unlocked
(travel) position
2nd
1st
Cam in locked position
Remove existing sill cushion and save for reuse.
Sill
Cushion
Flat Blade
Screwdriver
11
Interior
10
Interior
4
9069158
Remove side jamb liner working from bottom to top, prying jamb liner
edge from frame to disengage as shown.
Jamb Liner
Jamb
Liner
13
Interior
Pull side jamb liner down slowly, while supporting head stop and remove
from frame. Dispose of side jamb liner properly.
14
Interior
Insert new side jamb liner behind head stop.
15
Interior
Position side jamb liner in frame, locking front lip behind interior side stop.
16
Interior
Jamb Liner
Interior
Side
Stop
Jamb Liner
Re-engage side jamb liner, working from bottom to top, pressing jamb
liner edge into frame to engage as shown.
17
Interior Balance
Shoe
Shoe
Balance
Cam
Flat Blade
Screwdriver
Unlocked
Position
Locked
Position
Insert at blade screwdriver into cam and pull down until shoe is aligned
with shoe on opposite side. Rotate cam ¼ turn to lock.
18
Interior
Side Jamb Liner
Head Stop
5
9069158
Slide outside side jamb liner insert down to sill.
19
Interior
Jamb Liner
Exterior Insert
Clean area with a clean cloth and denatured alcohol.
Clean Cloth and
Denatured Alcohol
20
Interior
Checkrail
Weatherstrip
Side Cutting
Pliers
Position wide end of sill cushion in jamb liner channel, adhesive side
down, and press into place.
Sill Cushion
21
Interior
Rotate top sash to engage pivot pins into balance shoes of exterior
channel. Push down until both pivot pins are fully engaged.
Balance
Shoes
Pivot Pin
22
Interior
Tilt
Latches
Tilt Latches
23
Interior
Tilt sash up, retracting tilt latches by sliding inward. Release tilt latches
to re-engage sash in frame. Verify top sash operation. Repeat steps
22-23 if sash does not operate correctly.
Insert top of jamb liner pocket cover, beveled side toward exterior, into
interior channel, sliding it up behind head stop. Press jamb liner pocket
cover rmly into place, starting at top, zippering down full length.
Jamb Liner
Pocket Cover
Interior
Channel
Beveled Side
24
Interior
Jamb Liner
Channel
Head
Stop
Wide End
Sill Cushion
▶For double hung units proceed to step 26.
6
9069158
Rotate bottom sash to engage pivot pins into balance shoes of interior
channel. Push down until both pivot pins are fully engaged.
Balance
Shoe
Interior
Channel
Pivot Pin
26
Interior
Tilt sash up, retracting tilt latches by rotating lock handles toward
center, then release lock handles to re-engage sash.
Lock
Handles
27
Interior
Verify sash operation. Repeat steps 26-27 if sash does not
operate correctly.
Lock
Handles
28
Interior
Close and lock sash.
Lock
Handles
30
Interior
Verify sash operation. Repeat steps 30-31 if
sash does not operate correctly.
Lock
Handles
29
Interior
▶Side jamb liner replacement procedure is
complete for monumental units.
Reapply interior side stop on frame. Repeat
on opposite side. Fasten with nish nailer.
Interior
Side
Stop
For Monumental Only
31
Interior
▶Side jamb liner replacement procedure is
complete for single and double hung
units.
▶For monumental units proceed to step 31.
Replace sash stop in the side jamb.
25
Interior
Sash Stop
Single Hung and Monumental Only
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6

Andersen 9069158 Side Jamb Liner Replacement Service Instructions

Andersen
Brand
Andersen
Model
9069158 Side Jamb Liner Replacement
Type
Service Instructions

Andersen 9069158 Side Jamb Liner Replacement:

The Andersen 9069158 Side Jamb Liner Replacement is a genuine Andersen replacement part designed for use with E-Series double-hung windows. It is used to replace worn or damaged side jamb liners, which are essential for the proper operation of the window.

The replacement process is relatively straightforward and can be completed in a few simple steps. First, remove the existing side jamb liner by prying it away from the frame. Then, insert the new side jamb liner into the frame, making sure to lock the front lip behind the interior side stop. Finally, re-engage the side jamb liner by pressing the jamb liner edge into the frame.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents