Andersen 9069187 Top Sash Replacement Service Instructions

Brand: Andersen

Model: 9069187 Top Sash Replacement

Type: Service Instructions

Top Sash

9069187 BA Revised 06/03/13

Top Sash Replacement Guide

for E-Series Double-Hung Windows

Thank you for choosing Andersen.

For questions call 1-888-888-7020. For more information and/or guides visit www.eaglewindow.com

Please leave this guide with building owner.

▶Read guide from beginning to end before starting maintenance procedure. Read all warnings and cautions during unit maintenance.

Parts Included

(1) Top Sash

▶For information, calculating, and design pressure ratings for E-Series windows and doors go to

www.eaglewindow.com/Wintelligence/Design-Pressure-Estimator.aspx

▶Check with your local building code ofcial to identify and conrm compliance with local building code requirements.

Tools Needed

∙Safety Glasses

∙Gloves

∙#2 Phillips Screwdriver

∙Needle Nose Pliers

∙Finish Nailer (for monumental units only)

∙Pliers (for monumental units only)

∙Putty Knife (for monumental units only)

Use caution when working at elevated

heights and around unit openings. Follow

manufacturers’ instructions for ladders and/

or scaffolding. Failure to do so may result in

injury or death.

Follow manufacturers’ instructions for hand

or power tools. Always wear safety glasses.

Failure to do so may result in injury and/or

product damage.

Windows and doors can be heavy. Use safe

lifting techniques and a reasonable number of

people with enough strength to lift, carry and

install window and door products to avoid injury

and/or product damage.

9069187

Slide tilt latches inward while tilting sash in 90 degrees.

Lower top sash 6”.

Tilt Latches

6 Inches

Interior

Interior Tilt

Latches

Pivot bottom sash to remove from window

frame as shown. Place sash on clean at work

surface, exterior side up.

Rotate and hold lock handles toward center

while tilting sash in 90 degrees.

Unlock window and raise bottom sash 4".

Lock

Handles

4 Inches

Lock

Handles

Interior

Bottom Sash

Pry interior side stop away from frame. Repeat on opposite side. Remove any nails from frame and

interior side stops.

Remove sash stop from the side jamb.

For Monumental Only

Single Hung and Monumental Only

▶For double hung units proceed to step 6.

Interior

▶For single and double hung units proceed to step 2.

Interior

Pliers

Interior Side Stop

Putty Knife

Interior Side Stop

9069187

Remove keeper screws and keepers and reapply in same location

on new sash.

Reapply check rail weatherstrip ush with sash edge on new sash.

Retract (slide) tilt latches and hold to expose screw. Remove tilt latch

screws and tilt latches and reapply in same location on new sash. Flip

sash interior side up.

Tilt Latch

Check Rail Weatherstrip

Align

to Edge

Keeper

Check Rail

Weatherstrip

Rotate replacement top sash to engage pivot pins into balance shoes of

exterior channel. Push down until both pivot pins are fully engaged.

Balance

Shoes

Pivot Pin

Remove check rail weatherstrip with a needle nose pliers. Save

for reuse.

Needle Nose Pliers

#2 Phillips Screwdriver

Check Rail

Interior

Pivot top sash to remove from window frame as shown. Place sash on

clean at work surface, exterior side up.

Interior

Top Sash

9069187

Verify sash operation. Repeat steps 16-17 if

sash does not operate correctly.

Close and lock window.

Lock

Handles

Lock

Handles

Rotate bottom sash to engage pivot pins into balance shoes of interior

channel. Push down until both pivot pins are fully engaged.

Tilt sash up, retracting tilt latches by rotating lock handles toward center,

then release lock handles to re-engage sash.

Lock Handles

Balance

Shoe

Interior

Channel

Pivot Pin

▶Top sash replacement procedure is

complete for single and double hung units.

▶For monumental units proceed to step 20.

Interior

Tilt

Latches

Tilt Latches

Tilt sash up, retracting tilt latches by sliding inward. Release tilt

latches to re-engage sash in frame. Verify top sash operation. Repeat

steps 13-14 if sash does not operate correctly.

Interior

Replace sash stop in the side jamb.

Interior

Sash Stop

Single Hung and Monumental Only

▶For double hung units proceed to step 16.

Reapply interior side stop on frame. Repeat

on opposite side. Fasten with nish nailer.

For Monumental Only

Interior

▶Top sash replacement procedure is

complete for monumental units.

Interior

Side Stop

Andersen 9069187 Top Sash Replacement Service Instructions

Andersen 9069187 Top Sash Replacement Service Instructions

Andersen 9069187 Top Sash Replacement Service Instructions

Related papers

Other documents