Tools Required
HermanMiller
Cosm Chair Disassembly for Recycling
How to recycle your cosm chair.
Power
Driver
6mm
Hex Bit
600 Pound
Quick Clamp
Flat Screw
Driver
T-
Torx Bit
T-
Torx Bit
Step
. Using T- Torx bit, unscrew the attachment bolt and remove the height
adjust control down.
#2 Mallet Li-o
Tool
Needle
Nose Pliers
Step
. Using flat screw driver, unhook the four tabs of upper antler cover
and take out.
Step
. Insert the flat screw driver into the lower antler cover hole and gently pry
down until both sides are released.
. Pull and take out the lower antler cover.
1HermanMiller for Cosm chair Dissembly Instructions1BM787 rev B
2HermanMiller for Cosm chair Dissembly Instructions1BM787 rev B
Step Step
. Using flat screw driver, li up and pull out the tilt housing cover. . slide in the flat screw driver from back of the tilt and catch the back
edge of cable actuator housing.
. Pry down and pop the control loose to take out.
. Using power drive with mm hex bit which needs to be inches long to
take out the arm from the chair.
Step
Note: For no arm plug, follow steps from 8 to .
For D arm, follow steps from to
Step
. Take out the shoulder bolt from the xed arm.
3HermanMiller for Cosm chair Dissembly Instructions1BM787 rev B
Step
. Using power drive with mm hex bit which needs to be inches long to
remove no arm plug from the chair.
Step
. Take out the shoulder bolt from the no arm plug.
Step
. Insert the flat screw driver into the notch and gently pry against the
latching tab and pull out the d upper arm assembly at the same time.
Step
. Using T- torx bit, unscrew the arm pad retainer bolt and
take out the arm pad.
4HermanMiller for Cosm chair Dissembly Instructions1BM787 rev B
Step
. Add inches extension to the power drive with mm hex bit which
needs to be inches long to remove d lower arm casting from the chair.
. Take out the shoulder bolt from the d lower arm casting.
Step
Step
. Place the pound quick clamp with jaws reversed in between
the frames of the chair and gently clamp until some resistance.
Note: Don’t over stretch the frame.
Step
. Remove the beam bolts using T- Torx bit.
5HermanMiller for Cosm chair Dissembly Instructions1BM787 rev B
Step
Step
. Take out the tilt bushing.
. Remove the nylon bushing by using needle nose pliers.
Step
. Pull out and up on the rear spine.
. Rotate the entire chair forward and take out the back frame assembly.
Step
. Take out the flange bushing.
6HermanMiller for Cosm chair Dissembly Instructions1BM787 rev B
Step
Step
. Remove the rear casting from the tilt.
. Make sure the tension block is all the way forward.
Step
. Place foot on the casting and apply pressure to the tilt and pull the
steel plate out at the same time.
. Take out the tilt bushing.
Step
7HermanMiller for Cosm chair Dissembly Instructions1BM787 rev B
Step Step
. Take out the spring boards from tilt.
. Remove the tilt from base.
Step Step
. Place the li-o tool by facing tappered edge against the
bottom of the tilt and hit with mallet.
. Remove the two screws from the tilt cassette to allow us to li
out the fulcrum and cassette.
8HermanMiller for Cosm chair Dissembly Instructions1BM787 rev B
Step
Step
. Strike using a mallet on nylon cap to release the base from cylinder.
. Slide base o cylinder.
Step
. Hold base and pull hard to remove caster from base.
Step
. Place nylon cap over the end of cylinder.
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
Herman Miller Cosm Stool Product Instructions
- Type
- Product Instructions
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Herman Miller Cosm Stool Product Instructions
-
-
-
-
-
-
-
-
-
Other documents
-
HermanMiller Renew Installation guide
-
-
Hay Nelson Cigar Bubble Pendant User manual
-
WiBase WB-N211 User manual
-
Roland VG-99 Owner's manual
-
-
-
-
-
