PackPack
1313
STAGE PAGE
61 The dashboard 207
62 Speedometer 210
63 Left caravan wall 213
64 The dashboard 216
65 Left caravan window 219
Published in the UK by De Agostini UK Ltd, Royds Withy King, 65 Carter Lane, London EC4V 5EQ.
Published in the USA by De Agostini Publishing USA, Inc., 299 Park Avenue • New York, New York 10171.
All rights reserved © 2020
Warning: Not suitable for children under the age of 14.
is product is not a toy and is not designed or intended for use in play.
Items may vary from those shown.
207
Your parts:
61A. Radio cover
61B. Ashtray cover
61C. Ashtray
61D. The right inner caravan wall
CP. 1.7 x 4mm screws
IP. 2 x 4mm screws
Stage 61: The dashboard
208
2 Insert the ashtray cover (61B) into the upper hole in the
dashboard, as shown.
1 Align the radio cover (61A) with the rectangular opening in the
dashboard. Secure in place with two CP screws.
3Now mount the ashtray (61C) under the cover and secure the
with a CP screw. 4 Align the tabs in the caravan roof panel with the corresponding
holes in the right outer wall (Stage 40). Secure the parts
together with three CP screws.
209
Here is how your assembly should look at the end of this stage. Keep any assemblies, unused parts and spares labelled to one side for later use.
5Place the right inner caravan wall (61D) onto the inside of
the right outer wall. First tighten three IP screws into the
indicated holes.
6Tighten a further four IP screws into the inner wall to secure it.
210
Your parts:
62A. Speedometer housing
62B. Speedometer
62C. Speedometer backlight
62D. Curtain
62E. Curtain rail
EP. 1.7 x 2.5 x 5mm screws
Stage 62: Speedometer
211
2Install the speedometer into the indicated location in the
dashboard. Secure in place with two EP screws.
1Insert the speedometer (62B) into the housing (62A), printed side
first, as shown.
3Press the speedometer backlight (62C) into the speedometer. 4Slide the curtain (62D) onto the curtain rail (62E).
212
Here is how your assembly should look at the end of this stage. Keep any assemblies, unused parts and spares labelled to one side for later use.
5Insert the ends of the curtain rail into the two holes over the
window in the right caravan wall.
213
Your parts:
63A. Function button 1
63B. Function button 1 housing
63C. Switch 1
63D. Left outer caravan wall
CP. 1.7 x 4mm screws
Stage 63: Left caravan wall
214
2Pass the end of the switch 1 (63C) through the hole in function
button 1 housing (63B). Guide the metal prongs through the
upper hole, and then fold them over the cross-piece.
1Insert function button 1 (63A) into the indicated hole in
the dashboard.
3Place the button housing onto the rear of the dashboard over
function button 1 and secure with a CP screw. 4Align the tabs of the caravan roof with the corresponding parts
of the left caravan wall (63D).
215
Here is how your assembly should look at the end of this stage. Keep any assemblies, unused parts and spares labelled to one side for later use.
5Secure the caravan wall to the roof with three CP screws.
216
Your parts:
64A. Function button 2
64B. Function button 2 housing
64C. Switch 2
64D. Reector mounts
64E. Reectors
CP. 1.7 x 4mm screws
EP 1.7 x 2.5 x 5mm screws
Stage 64: The dashboard
217
2Pass the end of switch 2 (64C) through function switch 2 housing
(64B), guiding the metal prongs through the upper hole. Then fold
them around the cross-piece to secure.
1 Insert function button 2 (64A) into the rectangular hole in the
dashboard next to the ashtray.
3Screw the housing over function button 2 with two CP screws. 4Place the reflectors (64E) into the reflector mounts (64D).
218
Here is how your assembly should look at the end of this stage. Keep any assemblies, unused parts and spares labelled to one side for later use.
5 Mount the reflectors to the corresponding points towards the
bottom of the left caravan wall and fix them in place with
two EP screws.
219
Your parts:
65A. Air intake chamber
65B. Left caravan window
KP. 2 x 3 x 5mm screws
EP. 1.7 x 2.5 x 5mm screws
Stage 65: Left caravan window
220
2Secure the chamber from the other side of the bulkhead with
two KP screws.
1Insert the posts on the bottom of the air intake chamber (65A)
into the two holes in the bulkhead.
3Place the left caravan window (65B) over the corresponding
opening in the left caravan wall, aligning the tabs with the
holes around the opening.
4Secure the window with four EP screws.
221
Here is how your assembly should look at the end of this stage. Keep any assemblies, unused parts and spares labelled to one side for later use.
/
