HME HS25D User manual

HME
Brand
HME
Model
HS25D
Category
Headsets
Type
User manual

Below you will find brief information for HS25, HS25D. These headsets are designed for use with HME beltpacks with MD4 male connector. The microphone boom can be positioned for either the right or the left side of the head. The fit of the headset can be adjusted by using the slide adjusts on either side of the headband. The microphone can be turned on by pulling the boom gently downward and turned off by pushing the boom gently upward.

Below you will find brief information for HS25, HS25D. These headsets are designed for use with HME beltpacks with MD4 male connector. The microphone boom can be positioned for either the right or the left side of the head. The fit of the headset can be adjusted by using the slide adjusts on either side of the headband. The microphone can be turned on by pulling the boom gently downward and turned off by pushing the boom gently upward.

HME# 400G755
Rev A 6/21/16
HS25 and HS25D Headsets
USER GUIDE
HS25 (single ear) and HS25D (dual ear) headsets are designed for use with HME beltpacks with MD4
male connector.
Using your HS25 Headset
Adjusting the Headset:
You can position the microphone boom for either the right or the
left side of the head.
You can adjust the fit of the headset by using the slide adjusts on
either side of the headband.
Microphone Boom operation:
Turn the headset microphone ON by pulling the boom gently
downward (down past the 10 O’clock / 2 O’clock angle).
Turn the headset microphone OFF by pushing the boom gently
upward (to above the 10 O’clock / 2 O’clock angle).
Headset and Beltpack Connection
Specification
Specification
Description
Headphone type
Closed Back, Dynamic
Headphone driver
40mm (1.57in), neodymium magnet, copper-clad aluminium wire voice coil
Mic element
Dynamic
Mic polar pattern
Hyper cardioid
Frequency response
40 – 20 000Hz
300 – 20 000Hz
Open circuit sensitivity
– 61.0 dB ± 3.5 dB (0dB=1V/1Pa, at 1KHz, typical)
Sensitivity (Headphone)
102±3 dB (SPL) / 1mW, at 1KHz, typical
98±3 dB (SPL) / 1mW, at 1KHz, typical
Max. input power
500mW
Impedance
HS25: 400 ohms ±30%, at 1KHz
HS25D: 200 ohms ±30%, at 1KHz
200 ohms ±30%, at 1KHz
Weight
245g without 8-pin cord assembly
315g without 8-pin cord assembly
Cable
1.25m long with 8-pin connector at headset end; 4-pin Mini-DIN connector
Copyright © 2016 HME All rights reserved.
HME and the HME logo are trademarks or registered trademarks of HM Electronics, Inc. The product described in this
document is distributed under licenses restricting its use, copying, distribution, and decompilation /reverse engineering.
No part of this document may be reproduced in any form by any means without prior written authorization of HME, an HME
Company.
  • Page 1 1
  • Page 2 2

HME HS25D User manual

HME
Brand
HME
Model
HS25D
Category
Headsets
Type
User manual

Below you will find brief information for HS25, HS25D. These headsets are designed for use with HME beltpacks with MD4 male connector. The microphone boom can be positioned for either the right or the left side of the head. The fit of the headset can be adjusted by using the slide adjusts on either side of the headband. The microphone can be turned on by pulling the boom gently downward and turned off by pushing the boom gently upward.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents