Workrite Ergonomics Sonoma Mobile Table Installation guide

Brand
Workrite Ergonomics
Model
Sonoma Mobile Table
Type
Installation guide
Workrite Ergonomics | 800.959.9675 www.workriteergo.com 1 of 4
8.5
mm
5
mm
35
mm
5
mm
NUMBER
PART
Information in this drawing is provided for reference only.
http://www.mcmaster.com
92290A256
Stainless Steel
Socket Head Cap Screw
© 2014 McMaster-Carr Supply Company
4
mm
Hex
M5 x 0.8 mm Thread
0.4126"
#3 Drive
0.134"3/4"
0.216"
#12 Screw Size
Assembly & Installation Instructions:
Sonoma Mobile Table Base
SON-MTB-48-X, SON-MTB-60-X, SON-MTB-72 -X
Parts Included
D Top Middle Support
Qty: 1
E Locking Caster
Qty: 4
F Tilt Button Base
Qty: 2
G Tilt Button Cover
Qty:2
A Left Leg Assembly
Qty: 1
B Right Leg Assembly
Qty: 1
C Top Frame Assembly
Qty: 1
H M6 × 1P × 35 mm
Socket Head Allen Bolt
Qty: 4
J #8 × ¾" Phillips
Countersunk Screw
Qty: 2
K #12 × ¾" Phillips Pan
Head Screw
Qty: 6
I M5 × 0.8P × 35 mm
Socket Head Allen Bolt
Qty: 4
L 4 mm Allen Wrench
Qty: 1
Tools Required:
Required, Sold Separately:
24" Deep: SNT4824-B3-XXXXXXX, SNT6024-B3-XXXXXXX, SNT7224-B3-XXXXXXX
30" Deep: SNT4830-B3-XXXXXXX, SNT6030-B3-XXXXXXX, SNT7230-B3-XXXXXXX
Options, Sold Separately:
Ganging Brackets: SN-GANGBRKT-B
Modesty Panel: SN-MODESTY-48-G, SN-MODESTY-60-G, SN-MODESTY-72-G
Power Drill/Screw Gun
with #2 Phillips driver bit
Power Drill/Screw Gun
with #3 Phillips driver bit
#2 Phillips Screwdriver #3 Phillips Screwdriver
or orAND
2 of 4 Workrite Ergonomics | 800.959.9675 www.workriteergo.com
Align the Left Leg (A) to the Top Frame (C) as shown.
Insert two (2) M6 × 1.0P × 35 mm Socket Head Allen Bolts (H) as shown and tighten securely with the long 4 mm Allen Wrench (L).
Insert two (2) M5 × 0.8P × 35 mm Socket Head Allen Bolts (I) as shown and tighten securely with a long 4 mm Allen Wrench (L).
Align the Right Leg (B) to the Top Frame (C) as shown.
Insert two (2) M6 × 1.0P × 35 mm Socket Head Allen Bolts (H) as shown and tighten securely with the long 4 mm Allen Wrench (L).
Insert two (2) M5 × 0.8P × 35 mm Socket Head Allen Bolts (I) as shown and tighten securely with the long 4 mm Allen Wrench (L).
ASSEMBLE FRAME
1.1
1.2
1.3
1.4
1.5
1.6
1
Hardware at actual size
H M6 × 1.0P × 35 mm Socket Head
Allen Bolt
I M5 × 0.8P× 35 mm Socket Head
Allen Bolt
H
I
B
1.5
1.4
1.6
1.1
C
Bolt Location View
I
I
H
H
8.5
mm
5
mm
35
mm
5
mm
NUMBER
PART
Information in this drawing is provided for reference only.
http://www.mcmaster.com
92290A256
Stainless Steel
Socket Head Cap Screw
© 2014 McMaster-Carr Supply Company
4
mm
Hex
M5 x 0.8 mm Thread
8.5
mm
5
mm
35
mm
5
mm
NUMBER
PART
Information in this drawing is provided for reference only.
http://www.mcmaster.com
92290A256
Stainless Steel
Socket Head Cap Screw
© 2014 McMaster-Carr Supply Company
4
mm
Hex
M5 x 0.8 mm Thread
I
1.3
H
1.2
A
Workrite Ergonomics | 800.959.9675 www.workriteergo.com 3 of 4
Thread the Tilt Button Base (F) into the top support on each side as shown and tighten rmly.
Snap the Tilt Button Cover (G) on the Tilt Button Base (F). Be sure you align the word “PRESS”
toward the top of the table so you can read it when the table is in use.
ASSEMBLE FRAME
2.1
2.2
2
Button Alignment
TOP
FF
2.1
2.2
G
G
4 of 4 Workrite Ergonomics | 800.959.9675 www.workriteergo.com
1500480 Rev B
ATTACH BASE TO TOP
Attach the Top Middle Support (D) with two (2) #8 × ¾" Countersunk Screws (J) into the pre-drilled holes in the
SNXXXX-B3-XXXXXXX Top and tighten securely.
Align Top Brackets on the base assembly to the pre-drilled holes in the Top and attach with three (3)
#12 × ¾" Phillips Pan Head Screws (K) into the right and left top brackets as shown and tighten securely.
Install four (4) locking Casters (E) pushing them into the legs as shown.
3.1
3.2
3.3
OPERATION OF THE SONOMA MOBILE TABLE
Flip Down for use
From either end “Press” the tilt release button in, ip
the top down until you hear it “click” into the horizontal
use position.
Flip Up for storage
From either end press the tilt release button, ip
the top up until you hear it “click” into the tilted top
storage position.
*If you have purchased the optional Ganging Bracket
Kits or Modest Panel refer to the assembly instruction
included with these options for assembly to your
Sonoma Mobile Table.
3.3
3.1
3.2
J #8 × ¾" Countersunk Screws
3
K #12 × ¾" Phillips Pan Head
Screws
Hardware at actual size
E
E
K
K
J
D
FLIP UP
FLIP UP
LIFT
PRESS
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Workrite Ergonomics Sonoma Mobile Table Installation guide

Brand
Workrite Ergonomics
Model
Sonoma Mobile Table
Type
Installation guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents