Workrite Ergonomics Essentia Benching System Installation guide

Brand
Workrite Ergonomics
Model
Essentia Benching System
Type
Installation guide
Workrite Ergonomics | 800.959.9675 www.workriteergo.com 1 of 24
Worksurfaces
Grommet Kits
Parts Included, Benching System Parts Required, Ordered Separately
Assembly & Installation Instructions:
Essentia ES3E60-B04-WP-S & ES3E72-B04-WP-S
Benching System, Four Stations
Parts List Quantity
Included Two Stations
ESSENTIA FRAME SETS, SILVER
ES3E54-72-S includes:
6608716-2PK-01
4435511-01
6013312-5472-01
4
4
4
Required/Included
ESSENTIA BENCH FOOT KIT, DUAL, SILVER
ES-BFK48-S 2 kits
(4 feet) Required/Included
ESSENTIA PROGRAMMABLE SWITCH
ES-P-SWITCH 4 Required/Included
POWER MODULE, CIRCUIT 1, BLACK
ACC-PMC1-4P2U-B 4 Required/Included
POWER JUMPER BLOCK, BLACK
ACC-PWR-JBLOCK-B 3 Required/Included
POWER IN FEED CABLE
ACC-PWR-IN-HDWR-B 1 Required/Included
POWER CROSS CABLE
58" W: ACC-PWR-CCBL-36 or
70" W: ACC-PWR-CCBL-48 3 Required/Included
50" SIDE TO SIDE CABLE Required/Included
ACC-PWR-JSSCBL-50-B 2
54" BACK TO BACK CABLE
ACC-PWR-JBBCBL-54-B 1 Required/Included
CABLE TROUGH WITH END PLATES
58" W: ACC-CBLTRKIT-53-S or
70" W: ACC-CBLTRKIT-65-S 4 Included
Parts List Quantity Two Stations
WORKSURFACE
Benching - 29" Deep Only
T5829-XX-B3-XXXXXXX-XXX or
T7029-XX-B3-XXXXXXX-XXX
(Options include width, grommet type, laminate
and edge band colors)
4Required/Order
Separately
GROMMET ONLY KIT
ACC-PWR-REMNT-X or
ACC-PWR-INMNT-X 4Required/Order
Separately
4 Station Essentia Benching System
2 of 24 Workrite Ergonomics | 800.959.9675 www.workriteergo.com
Workcenters
Trough
Benching
Foot Kit
Foot
Connectors
Inlay Power
Grommets
Back to Back
Cable
Side to Side
Cables
Power In
Feed
Recessed
Power
Table of Contents
Step Page
You will assemble FOUR complete Benching Workcenters joined by a TWO pair of
Benching Feet.
Build Workcenters Page 3
ES3E54-72-S
Add Power & Recessed Mount Kit Page 11
ACC-PMC1-4P2U-B, ACC-PWR-JBLOCK-B, ACC-PWR-CCBL-36 or
ACC-PWR-CCBL-48, ACC-PWR-REMNT-X
Add Trough Page 15
ACC-CBLTRKIT-53-S or ACC-CBLTRKIT-65-S
Add Benching Foot Kits Page 17
ES-BFK48-S
Connect Benching Pairs Page 18
ES-BF-CONKIT-S
Add Inlay Mount Kit (if applicable) Page 20
ACC-PWR-INMNT-X
Install Grommets Page 21
ACC-PWR-REMNT-X or ACC-PWR-INMNT-X
Connect Side to Side & Back to Back Cables Page 21
ACC-PWR-JSSCBL-50-B, ACC-PWR-JBBCBL-54-B
Connect Power Page 23
ACC-PWR-IN-HDWR-B
Adjust Glides Page 24
Initialize Legs Page 24
Workrite Ergonomics | 800.959.9675 www.workriteergo.com 3 of 24
Workrite Ergonomics | 800.959.9675 www.workriteergo.com 1 of 10
Box1: 6608716-2PK-01 Box2: 4435511-01
Box3: 6013312-5472-01
Parts Included, Frame Set
Required & Sold Separately
H 4 mm Allen Wrench
Qty: 1
N Power Cord
Qty: 1
K Cable Spool
Qty: 2
M " White Leg Cable Loops
Qty: 10
B Rear Bracket
Qty: 2 C Connector Bracket
Qty: 1
A Legs
Qty: 2 E Short Bracket
Qty: 2
J Control Box
Qty: 1
F Le End Bracket
Qty: 1
G Right End Bracket
Qty: 1
D #M6 × 12 mm Flat Head Cap Screw
Qty: 8
D #M6 × 12 mm Flat Head Cap Screw
Qty: 12
L #8 × ⅝" Pan Head Screw
Qty: 10
I #12 × ¾" Pan Head
Laminate Top Screw
Qty: 40
Assembly & Installation Instructions:
Essentia 2-Leg Workcenter ES2E54–72, ES3E54-72
Foot Kit
Basic or Programmable Switch
Top
2 of 10 Workrite Ergonomics | 800.959.9675 www.workriteergo.com
Verify that you have all the tools needed for the assembly
You will need the following tools:
#2 tip Phillips screwdriver or drill/driver
#3 tip Phillips screwdriver or drill/driver
M4 tip bit or 4 mm Allen Wrench (I)
If you do not have a Workrite worksurface, you will also need:
⅛" pilot drill bit
" pilot drill bit
Essentia 2-leg
V = 120 VAC, 60 Hz / 8 A maximum
IMPORTANT SAFETY INSTRUCTIONS:
When using an electrical furnishing, basic precautions should always be followed, including the following:
Read all instructions before using this Essentia Workcenter.
DANGER: To reduce the risk of electric shock, always unplug this Essentia Workcenter from the electrical outlet before
cleaning.
WARNING: To reduce the risk of burns, fire, electric shock, or injury to persons:
1. Unplug from outlet before putting on or taking o parts.
2. Close supervision is necessary when this furnishing is used by, or near children, invalids, or disabled persons.
3. Use this furnishing only for its intended use as described in these instructions. Do not use attachments not recommended by the
manufacturer.
4. Never operate this furnishing if it has a damaged cord or plug, if it is not working properly, if it has been dropped or damaged, or
dropped into water. Return the furnishing to a service center for examination and repair.
5. Keep the cord away from heated surfaces.
6. Do not use outdoors.
7. Do not operate where aerosol (spray) products are being used or where oxygen is being administered.
8. To disconnect, remove plug from outlet.
9. Each surface intended to support an equipment payload of 225 pounds.
FOR COMMERCIAL USE ONLY
SAVE THESE INSTRUCTIONS
or
✓
IMPORTANT NOTE!
You must complete initialization (Step 13) at the end of
assembly or your workcenter WILL NOT FUNCTION PROPERLY.
4 of 24 Workrite Ergonomics | 800.959.9675 www.workriteergo.com
2 of 10 Workrite Ergonomics | 800.959.9675 www.workriteergo.com
Verify that you have all the tools needed for the assembly
You will need the following tools:
#2 tip Phillips screwdriver or drill/driver
#3 tip Phillips screwdriver or drill/driver
M4 tip bit or 4 mm Allen Wrench (I)
If you do not have a Workrite worksurface, you will also need:
⅛" pilot drill bit
" pilot drill bit
WARNING: Maximum loading of table assembly is 225 lb. (102 kg). Maximum load includes the weight of the
table top itself, any equipment placed upon it, and any equipment suspended or hanging under it. Loading should be evenly distributed
over table surfaces. “Payload Capacity” is the Workrite Ergonomics recommended maximum loading which includes the Workrite sourced
table top.
Essentia 2-leg
V = 120 VAC, 60 Hz / 8 A maximum
IMPORTANT SAFETY INSTRUCTIONS:
When using an electrical furnishing, basic precautions should always be followed, including the following:
Read all instructions before using this Essentia Workcenter.
DANGER: To reduce the risk of electric shock, always unplug this Essentia Workcenter from the electrical outlet before
cleaning.
WARNING: To reduce the risk of burns, fire, electric shock, or injury to persons:
1. Unplug from outlet before putting on or taking o parts.
2. Close supervision is necessary when this furnishing is used by, or near children, invalids, or disabled persons.
3. Use this furnishing only for its intended use as described in these instructions. Do not use attachments not recommended by the
manufacturer.
4. Never operate this furnishing if it has a damaged cord or plug, if it is not working properly, if it has been dropped or damaged, or
dropped into water. Return the furnishing to a service center for examination and repair.
5. Keep the cord away from heated surfaces.
6. Do not use outdoors.
7. Do not operate where aerosol (spray) products are being used or where oxygen is being administered.
8. To disconnect, remove plug from outlet.
9. Each surface intended to support an equipment payload of 225 pounds.
FOR COMMERCIAL USE ONLY
SAVE THESE INSTRUCTIONS
or
✓
IMPORTANT NOTE!
You must complete initialization (Step 13) at the end of
assembly or your workcenter WILL NOT FUNCTION PROPERLY.
26
Workrite Ergonomics | 800.959.9675 www.workriteergo.com 5 of 24
Workrite Ergonomics | 800.959.9675 www.workriteergo.com 3 of 10
Assemble Rear Brackets to Connector Bracket
Assemble Rear Brackets (B) to Connector Bracket (C) using
#M6×10 mm Flat Head Cap Screws (D).
Use this guide to determine the correct holes for mounting
based on the width of your workcenter.
Tighten securely.
Layout Legs and Brackets
Lay out Legs (A) and Brackets (B, C, E, F and G) on
the floor.
61"
55"
49"
43"
D
H
D
D
D
B
B
B
B
B
B
B
B
C
C
C
C
2
1
F
B
B
A
A
G
E
E
C
To avoid stripping the threads, always
insert and make the first few turns
of the screw BY HAND with an Allen
wrench (H), ensuring it is in straight.
52" Workcenters
58" Workcenters
64" Workcenters
70" Workcenters
D #M6 × 12 mm Flat Head
Cap Screw
Hardware at actual size
Note!
Only use the #M6 × 12 mm Flat Head
Cap Screws for assembly.
6 of 24 Workrite Ergonomics | 800.959.9675 www.workriteergo.com
4 of 10 Workrite Ergonomics | 800.959.9675 www.workriteergo.com
Attach Short & Medium Brackets
Attach Short Brackets (E) using
#M6×12mm Flat Head Cap Screws (D) to
both legs.
Attach Right End Bracket (G) to sides of
the Leg (A) using Flat Head Cap Screws
(D). Attach Le End Bracket (F) to sides
of the other Leg (A) using Flat Head Cap
Screws (D).
Tighten securely.
Note: The right bracket will be on your le and vice versa when the
assembly is seen upside down.
E
E
G
F
D
D
D
D
D
D
To avoid stripping the threads, always
insert and make the first few turns
of the screw BY HAND with an Allen
wrench (H), ensuring it is in straight.
Le Leg
Right Leg
Right Bracket
Le Bracket
front
B
B
C
Assembled
3
A
A
H
D #M6 × 12 mm Flat Head
Cap Screw
Hardware at actual size
Caution!
Only use the #M6 × 12 mm Flat Head
Cap Screws for assembly. Use of longer
screws will damage the legs.
Workrite Ergonomics | 800.959.9675 www.workriteergo.com 7 of 24
Workrite Ergonomics | 800.959.9675 www.workriteergo.com 5 of 10
Attach Base to Workrite Pre-Drilled Workrite Worksurface
If you have a non-Workrite worksurface skip to Step 5.
Note: For 2-Leg Corner and 120° Worksurface Mounting Instructions, go to: www.workriteergo.com/instructions
Position leg assembly to align
mounting holes in brackets to pre-
drilled holes in worksurface.
Attach at the four corner locations
using #12 × ¾" Pan Head Laminate
Top Screws (I). If you use an electric
screwdriver, be sure it is on the
lowest torque setting to avoid
stripping the holes in the top.
With frame set positioned and the four corner screws secure, attach frame set using the remaining #12 × ¾" Pan
Head Laminate Top Screws (I).
Tighten securely.
I
I
I
I
3 screws per
Short Bracket
2 screws per End Bracket
(2 installed in Step 4b)
16 screws per
Rear Bracket Assembly
a
a
front
bb
b
c
c
c
b
a
b
c
4
I #12 × ¾" Pan Head
Laminate Top Screw
Hardware at actual size
8 of 24 Workrite Ergonomics | 800.959.9675 www.workriteergo.com
Attach Control Box & Cable Spools to Worksurface
Position Control Box (J).
With Control Box (J) positioned over pilot holes, attach with two #12 × ¾" Pan Head Screws (I).
Attach Cable Spool (K) with the #12 × ¾" Pan Head Screw (I) to underside of worksurface. If you do not have a
Workrite worksurface, mount Cable Spools (K) in a convenient location between Legs and Control Box. Lay out
Switch and Leg Cables (A) to be sure they all reach the Control Box.
Attach Programmable Switch
Position the Switch over the pilot holes near front edge of worksurface.
Attach Switch to underside of worksurface using the #8×⅝" Pan Head
Screws provided with your Programmable Switch.
#8 × ⅝" Pan Head
Screw
a
a
b
c
c
c
b
K
K
J
I
I
I
I
A
A
I #12 × ¾" Pan Head
Laminate Top Screw
Hardware at actual size
6
front
b
a
a
b
Hardware provided with switch
at actual size
5
Workrite Ergonomics | 800.959.9675 www.workriteergo.com 9 of 24
Attach Cable Loops and Route Cables
Attach " White Leg Cable Loops (M) to underside of worksurface using #8 × ⅝" Pan Head Screw (L) making
sure to wrap the Cable Loop around the cable prior to attaching. If you do not have a Workrite worksurface,
attach cable loops in a convenient locations between Legs or Switch and the Control Box.
Use the ⅛" Black Switch Cable Loops and screws from your Workrite Switch to secure your Switch Cable.
L #8 × ⅝" Pan Head
Screw
7
L
⅛" Black Switch
Cable Loops and
screws from your
Workrite Switch
⅛" Black Switch
Cable Loops and
screws from your
Workrite Switch
" White Leg
Cable Loops (M)
" White Leg
Cable Loops (M)
M
L
M
Hardware at actual size
10 of 24 Workrite Ergonomics | 800.959.9675 www.workriteergo.com
Connect Leg Cables, Switch Cable and Power Cord to Control Box
Connect the Leg Cable (A) to the six position leg ports “M1” & “M2” on the Control Box (J).
Insert the Switch Cable into the switch port “HS” on the Control Box (J).
Insert the Power Cord (N) into the power port on the Control Box (J).
A
A
N
N
J
J
Leg Cable (A) into Leg Ports
“M1” & “M2”
Switch Cable into Switch Port
“HS”
Power Cord (N ) in Power Port
b
a
c
b
a
c
Repeat for all workstations before continuing to next step.
8
8
Workrite Ergonomics | 800.959.9675 www.workriteergo.com 11 of 24
Workrite Ergonomics | 800.959.9675 www.workriteergo.com 1 of 8
or
or
Power Modules & Cables
Inlay Mount Kit Recessed Mount Kit
Power In Feed OptionsPower Jumper Cable
Required & Sold Separately
Optional & Sold Separately
Circuit 2 Power Module
Qty: 1
Circuit 1 Power Module
Qty: 1
Inlay Face Plate
Qty: 1
#8 × " Phillips Head
Screw - Black
Qty: 2
Cable Loop
Qty: 2
Recessed Face Plate
Qty: 1
Power In Cable, 96" Hardwire,
Dual Circuit
Qty: 1
Installation Manual
Qty: 1
Installation Manual
Qty: 1
Power In Cable, 96"QD Plug
Qty: 1
Wall Plate
Qty: 1
Mounting Tabs
Qty: 2
#10 × " Phillips Head
Screw - Black
Qty: 4
#10 × " Phillips Head
Screw - Black
Qty: 4
#6 × " Phillips Head
Screw - Black
Qty: 2
Grommet Cover
Qty: 1
Oval Grommet
Qty: 2 Oval Grommet
Qty: 2
"-20 Flange Nut-Silver
Qty: 2
¼"-20 Thumb Nut-
Black
Qty: 2
Back To Back Jumper
Cable, 54" - Black
Qty: 1
Side To Side Jumper
Cable, 50" - Black
Qty: 1
"-20 Flange Nut-Silver
Qty: 2
Jumper Block
Qty: 1
Power Cross Cable-Silver
24", 36" or 48"
Qty: 1
Assembly & Installation Instructions:
Benching Daisy Chain Power System
Benching Foot Kit, Benching Foot Connector Kit, Benching Worksurface, Switch
2-Leg Electric Essentia, Sierra HX or Sierra HXL Frameset (48" W / 60" W / 72" W × 30" D)
Cable Management Trough, Rigid Modesty Panel, Cable Management, Privacy/Sound Panels
ACC-PMC2-4P2U-BACC-PMC1-4P2U-B
ACC-PWR-INMNT-X
ACC-PWR-JSSCBL-50-B ACC-PWR-IN-HDWR-B ACC-PWR-IN-FFP-B
ACC-PWR-JBBCBL-54-B
ACC-PWR-REMNT-X
ACC-PWR-JBLOCK-B ACC-PWR-CCBL-XX
Required for 6, 8 and 10
desk Benching Systems
All instruction quantities are per workcenter.
12 of 24 Workrite Ergonomics | 800.959.9675 www.workriteergo.com
2 of 8 Workrite Ergonomics | 800.959.9675 www.workriteergo.com
THIS ELECTRICAL SYSTEM IS UL CERTIFIED BY ETL FOR USE AS DESCRIBED BELOW. ALL SPECIFICATIONS
AND WARNINGS MUST BE FOLLOWED CLOSELY IN ASSEMBLY AND USE OF THIS SYSTEM.
CAUTIONS AND WARNINGS
WARNING: FAILURE TO FOLLOW CAUTIONS AND WARNINGS BELOW COULD RESULT IN ELECTRICAL SHOCK,
FIRE, PROPERTY DAMAGE, PERSONAL INJURY, OR DEATH.
CAUTIONS:
•Read Instructions: Read all warnings and installation instructions before installing and use
•Retain Instructions: Retain this instruction sheet for future use
•Wet Environment
· This system is designed for use indoors in a dry environment
· Never use this system in a wet environment
· Never allow liquids of any type to spill into the electrical system
•Follow Warnings: Read and follow all warnings and directions in this instruction sheet and marked on the components of the
system
•Service
· There are no serviceable parts contained in this system
· Do not open and or modify any parts used in this electrical system
WARNINGS:
•Risk of fire or electrical shock
· Do not electrically connect to more than one source of power supply
· Always verify the electrical system is only connected to one and only one source of power supply
•Power Entry Cable
· Route the Power Entry Cable where it will not be stepped on, pinched, have devices placed on it, or become a tripping hazard
· Never allow Power Entry Cable to sit in any liquid or get wet in any manner
•Power Cross Cables
· Secure the Power Cross Cables to the underside of the worksurface using P-Loops and screws provided
· Ensure the Power Cross Cables will not be pinched or have devices placed on them
· Never allow Power Cross Cables to sit in any liquid or get wet in any manner
•Power Jumper Cables: Side to Side or Front to Back
· Install Power Jumper Cables only when benching feet and foot connectors are installed and in use
· Ensure the Power Jumper Cables will not be pinched or have devices placed on them
· Never allow Power Jumper Cables to sit in any liquid or get wet in any manner
•Location: This system is intended for use indoors in a dry environment only
SYSTEM DESCRIPTION AND REQUIREMENTS: DAISY CHAIN POWER SYSTEM
•Limits & Restrictions
· Four wire system designed to operate using two dedicated 120 V, 60 Hz, 20 A circuits
· Power Modules o ered in Circuit 1 and Circuit 2 options
· Total power modules per four wire dual circuit system not to exceed 10 total modules (Maximum five each Circuit 1 and Circuit 2)
· The Daisy Chain Power System may only be installed in Workrite height adjustable workcenters that are connected with either Bench Feet (see
parts list) as back to back stations or as multiple bench systems using both Bench Feet and Bench Foot Connectors (see parts list)
•Assembly
· All assembly must be completed as outlined in the assembly instructions. All system parts must be used as supplied with no alterations or
modifications
•Connection/Power Entry
· Power Connection for power entry options o ered with this daisy chain power system must be connected by a commercial electrician
Workrite Ergonomics | 800.959.9675 www.workriteergo.com 13 of 24
Workrite Ergonomics | 800.959.9675 www.workriteergo.com 3 of 8
Verify that you have all the tools needed for the assembly
You will need the following tools:
#2 tip Phillips screwdriver or drill/driver
" Wrench
✓
or and
Install Power Jumper Block
Attach Power Jumper Block to underside of worksurface
using the four #10 × " Phillips Head Screws included
with the Power Jumper Block.
Note: No Power Jumper Block is used on last workcenter
with the daisy chain power system.
Connect Power Cross Cable
Connect the Power Cross Cable to the Jumper Block by inserting the plug into the
receptacle.
Note: Orientation of the plug to the receptacle is important and can
only connect one way. Make sure colored ports are aligned so the
colors match on the Power Module and Jumper Block.
Attach Cable Loops to underside of worksurface
using #8 × " Phillips Head Screw making sure
to wrap the Cable Loop around the cable prior to
attaching.
Note: No Power Cross Cable is
used on last workcenter with
the daisy chain power system.
1
2
a
a
b
b
b
Install Power Jumper Block
Attach Power Jumper Block to underside of worksurface
using the four #10 × " Phillips Head Screws included
with the Power Jumper Block.
Note: No Power Jumper Block is used on last workcenter
with the daisy chain power system.
Connect Power Cross Cable
Connect the Power Cross Cable to the Jumper Block by inserting the plug into the
receptacle.
Note: Orientation of the plug to the receptacle is important and can
only connect one way. Make sure colored ports are aligned so the
colors match on the Power Module and Jumper Block.
Attach Cable Loops to underside of worksurface
using #8 × " Phillips Head Screw making sure
to wrap the Cable Loop around the cable prior to
attaching.
Note: No Power Cross Cable is
used on last workcenter with
the daisy chain power system.
1
2
a
a
b
b
b
9
10
Repeat for all workstation before continuing to next step.
The last workstation on a daisy chain power system does not include Cross Cable or Jumper Block.
14 of 24 Workrite Ergonomics | 800.959.9675 www.workriteergo.com
Workrite Ergonomics | 800.959.9675 www.workriteergo.com 5 of 8
Install Recessed Power Module
If you have an Inlay Power Module, skip to Step 4
Attach Recessed Face Plate to underside of worksurface using the four #10 × " Phillips Head Screws included
with Recessed Face Plate.
Remove the two "-20 Flange Nuts from the studs on the Recessed Face Plate.
Using a " wrench, attach the Recessed Face Plate to the Power Module with the two "-20 Flange Nuts.
Connect the Power Cross Cable to the Power Module by inserting the plug into the receptacle.
Note: Orientation of the plug to the receptacle is important and can only connect one way. Make sure colored
ports are aligned so the colors match on the Power Module and Jumper Block.
Attach Benching Feet & Flip Benching Set Over
Align two workcenters back to back
Attach Feet according to instructions that came
with your Foot Kit.
Flip over Benching Set. Note: Flip over onto side
so you do not damage the control. Use at least
two people to flip over Benching Set.
IMPORTANT NOTE!
You must use benching feet. Flipping over benching sets takes
at least two people. CAUTION, HEAVY!
a
a
a
a
b
b
b
b
c
c
c
c
c
3
4
Flip onto side so you do
not damage the control.
11
Step 12.
Repeat for all workstations before continuing to next step. Power System will be completed aer
workcenters are flipped right side up.
Workrite Ergonomics | 800.959.9675 www.workriteergo.com 15 of 24
Workrite Ergonomics | 800.959.9675 www.workriteergo.com 1 of 2
Parts Included
Assembly & Installation Instructions:
Cable Trough, ACC-CBLTRKIT-XX-X
Attach Tough Ends to Cable Trough
Slide Trough Ends (B & C) onto Cable
Trough (A).
Attach from below using #10-32 × "
Pan Head Machine Screws (F). Repeat for
other side.
If Installing optional Rigid Modesty
Panel, skip to Step 2.
Attach from behind Trough using the
#10-32 × " Pan Head Machine Screws
(D) and the #10-32 Hex Nuts (E). Repeat
for other side.
A Cable Trough
Qty: 1 B Le Trough
End
Qty: 1
C Right Trough
End
Qty: 1 G #12 × " Pan Head
Wood Screw
Qty: 8
Verify that you have all the tools needed for the assembly
#2 tip Phillips screwdriver over 6" long
or drill/driver with extension
" wrench if needed for Hex Nut (E)
or
Optional & Sold Separately
Daisy Chain Power System, Rigid Modesty Panel
41", 53" or 65" long
D#10-32 × " Pan Head
Machine Screws
Qty: 8
E#10-32 Hex Nut
Qty: 4
F #10-32 × " Pan Head
Machine Screws
Qty: 2
+6"
+6"
+6"
+6"
1
B
C
A
✓
a
a
a
c
c
b
b
D
E
F
Trough only installation
12
per workcenter
16 of 24 Workrite Ergonomics | 800.959.9675 www.workriteergo.com
Workrite Ergonomics | 800.959.9675 www.workriteergo.com 2 of 2
1500283 Rev B
Attach Cable Trough to Underside of Worksurface
Align holes in Cable Trough with holes
in bottom of your Workrite pre-drilled
worksurface.
Attach Trough assembly using the #12 × "
Phillips Pan Head Screws (G). Access holes
provide easy attachment with long screwdriver.
Under Benching Worksurface with optional Rigid Modesty Panel
& Daisy Chain Power System
Attach Tough Ends to Cable Trough With Optional Rigid Modesty Panel
Skip this step unless you've purchased the Rigid Modesty Panel ACC-MODPNL-XX-B3
Attach Trough (A) to the threaded inserts
on the Rigid Modesty Panel from inside
Trough using the eight #10-32 × " Pan
Head Machine Screws (D).
3
a
b
2G
Access hole
A
D
Optional Rigid Modesty Panel
ACC-MODPNL-XX-B3
13
Repeat for all workstations before continuing to next step.
Workrite Ergonomics | 800.959.9675 www.workriteergo.com 17 of 24
Workrite Ergonomics | 800.959.9675 www.workriteergo.com 1 of 2
Parts Included
Assembly & Installation Instructions:
Essentia Benching Foot Kit, ES-BFK48-X
A Benching Feet with Glides
Qty: 2 B #M6 × 18 mm Flat
Head Cap Screw
Qty: 16 D Hole Plug
Qty: 20
C 4 mm Allen Wrench
Qty: 1
Verify that you have all the tools needed for the assembly
4 mm Allen Wrench (C) supplied
Note!
Only use the #M6 × 18 mm Flat Head
Cap Screw (B) supplied with the
Benching Foot Kit to attach feet.
Fill outside facing foot holes with Hole Plugs (D). If you are building a Benching
System with multiple side by side workcenters, wait until you've completed
joining your workcenter pairs before adding Hole Plugs.
Flip over Benching Set. Note: Flip over onto side so you do not damage the
control. Use at least two people to flip over Benching Set.
Attach Sierra Benching Feet
Align two workcenters back to back
Attach Feet (A) using Allen Wrench (C) and the #M6
× 18 mm Flat Head Cap Screws(B).
Parts Included
B #M6 × 18 mm Flat Head
Cap Screw
Hardware at actual size
✓
a
b
1
c
d
d
a
b
C
B
B
B
A
A
B
D
D
D
D
Flip onto side so you do
not damage the control!
c
Caution! Heavy!
Flipping over benching sets takes at least two people. CAUTION,
HEAVY! Flip over onto side so you do not damage the control.
14
Repeat for all benching sets before continuing to next step.
18 of 24 Workrite Ergonomics | 800.959.9675 www.workriteergo.com
IMPORTANT NOTE!
You need to anticipate the final Benching System placement and power-in location prior to
connecting Benching Workcenter pairs. Once Workcenters have been connected it is very
diicult to move or rearrange a complete Benching System. CAUTION! HEAVY!
Workrite Ergonomics | 800.959.9675 www.workriteergo.com 1 of 2
Parts Included
Assembly & Installation Instructions:
Benching Foot Connector Kit, ES-BFK-CONKIT-X,
SE-BF-CONKIT-X
Attach Foot Connector to First Benching Foot
Align two Benching Workcenters side by side
leaving room to install Foot Connector (A).
Attach Foot Connector (A) loosely to the first
workcenter using the #M6 × 12 mm Flat Head
Cap Screws(C) and Allen Wrench. Repeat at
the second connection.
Caution!
Only use the #M6 × 12 mm Flat Head Cap Screw (C)
supplied with the Benching Foot Connector Kit to attach.
A Connector Plate
Qty: 2 B Cover Plate
Qty: 2 C #M6 × 12 mm Flat Head
Cap Screw
Qty: 8
Verify that you have all the tools needed for the assembly
4 mm Allen Wrench supplied with Benching Foot Kit
Required & Sold Separately
Benching Foot Kit
Hardware Included
a
a
b
b
b
1
C #M6 × 12 mm Flat Head
Cap Screw
Hardware at actual size
A
A
C
C
Bench Set 1
Bench Set 2
✓
Parts Included
Assembly & Installation Instructions:
Benching Foot Connector Kit, ES-BFK-CONKIT-X,
SE-BF-CONKIT-X
Attach Foot Connector to First Benching Foot
Align two Benching Workcenters side by side
leaving room to install Foot Connector (A).
Attach Foot Connector (A) loosely to the first
workcenter using the #M6 × 12 mm Flat Head
Cap Screws(C) and Allen Wrench. Repeat at
the second connection.
Caution!
Only use the #M6 × 12 mm Flat Head Cap Screw (C)
supplied with the Benching Foot Connector Kit to attach.
A Connector Plate
Qty: 2 B Cover Plate
Qty: 2 C #M6 × 12 mm Flat Head
Cap Screw
Qty: 8
Verify that you have all the tools needed for the assembly
4 mm Allen Wrench supplied with Benching Foot Kit
Required & Sold Separately
Benching Foot Kit
Hardware Included
a
a
b
b
b
1
C #M6 × 12 mm Flat Head
Cap Screw
Hardware at actual size
A
A
C
C
Bench Set 1
Bench Set 2
✓
15
Workrite Ergonomics | 800.959.9675 www.workriteergo.com 19 of 24
Fill outside facing holes in the feet with the Hole Plugs from the Benching Foot Kit aer all benching pairs are
connected
Workrite Ergonomics | 800.959.9675 www.workriteergo.com 2 of 2
1500285 Rev A
Attach Cover Plate
Attach Cover Plate (B) to Connector Plate(A)
by sliding under lip on foot. Magnet holds
cover in place.
Repeat as Required to Join All Benching Sets
Repeat from Step 1 as required to join all benching sets.
Attach Foot Connector to Second Benching Foot
Move second Benching Workcenter over to attach
Foot Connector (A).
Attach Foot Connector (A) to the second workcenter
loosely using the #M6 × 12 mm Flat Head Cap
Screws(C) and Allen Wrench. Repeat at the second
connection.
Once loosely assembled, tighten all screws to secure
benching pairs together.
B
3
✓
Lip
a
a
b
b
2
A
C
Facing Out
b
a
a
b
17
Repeat for all workcenters before continuing to next step.
16
20 of 24 Workrite Ergonomics | 800.959.9675 www.workriteergo.com
Install Grommets
For both Inlay Mount Kit and Recessed
Mount Kit, place Oval Grommets into oval
cutouts in Worksurface
For Recessed Mount Kits, place the
Grommet Cover into rectangular cutout and
lock in place with two #6 × " Phillips Head
Screws.
Install Inlay Power Module
If you've installed a Recessed Power Module, skip to Step 6.
Remove the two "-20 Flange Nuts from the studs on the Inlay Face Plate.
Using a " wrench, attach the Inlay Face Plate to the Power Module with the two "-20 Flange Nuts.
Insert Power Module and Face Plate assembly into cutout in Worksurface.
From below the worksurface, slide the two Mounting Tabs onto the threaded posts from the Face Plate and
secure in place using two ¼"-20 Thumb Nuts.
Connect the Power Cross Cable to the Power Module by inserting the plug into the receptacle.
Note: Orientation of the plug to the receptacle is important and can only connect one way. Make sure colored
ports are aligned so the colors match on the Power Module and Jumper Block.
6
5
a
a
b
b
c
c
d
d
a
a
a
bb
Below
Below
Workrite Ergonomics | 800.959.9675 www.workriteergo.com 1 of 8
or
or
Power Modules & Cables
Inlay Mount Kit Recessed Mount Kit
Power In Feed OptionsPower Jumper Cable
Required & Sold Separately
Optional & Sold Separately
Circuit 2 Power Module
Qty: 1
Circuit 1 Power Module
Qty: 1
Inlay Face Plate
Qty: 1
#8 × " Phillips Head
Screw - Black
Qty: 2
Cable Loop
Qty: 2
Recessed Face Plate
Qty: 1
Power In Cable, 96" Hardwire,
Dual Circuit
Qty: 1
Installation Manual
Qty: 1
Installation Manual
Qty: 1
Power In Cable, 96"QD Plug
Qty: 1
Wall Plate
Qty: 1
Mounting Tabs
Qty: 2
#10 × " Phillips Head
Screw - Black
Qty: 4
#10 × " Phillips Head
Screw - Black
Qty: 4
#6 × " Phillips Head
Screw - Black
Qty: 2
Grommet Cover
Qty: 1
Oval Grommet
Qty: 2 Oval Grommet
Qty: 2
"-20 Flange Nut-Silver
Qty: 2
¼"-20 Thumb Nut-
Black
Qty: 2
Back To Back Jumper
Cable, 54" - Black
Qty: 1
Side To Side Jumper
Cable, 50" - Black
Qty: 1
"-20 Flange Nut-Silver
Qty: 2
Jumper Block
Qty: 1
Power Cross Cable-Silver
24", 36" or 48"
Qty: 1
Assembly & Installation Instructions:
Benching Daisy Chain Power System
Benching Foot Kit, Benching Foot Connector Kit, Benching Worksurface, Switch
2-Leg Electric Essentia, Sierra HX or Sierra HXL Frameset (48" W / 60" W / 72" W × 30" D)
Cable Management Trough, Rigid Modesty Panel, Cable Management, Privacy/Sound Panels
ACC-PMC2-4P2U-BACC-PMC1-4P2U-B
ACC-PWR-INMNT-X
ACC-PWR-JSSCBL-50-B ACC-PWR-IN-HDWR-B ACC-PWR-IN-FFP-B
ACC-PWR-JBBCBL-54-B
ACC-PWR-REMNT-X
ACC-PWR-JBLOCK-B ACC-PWR-CCBL-XX
Required for 6, 8 and 10
desk Benching Systems
18
Step 19.
, (continued)
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24

Workrite Ergonomics Essentia Benching System Installation guide

Brand
Workrite Ergonomics
Model
Essentia Benching System
Type
Installation guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents