Workrite Ergonomics Essentia Benching System Installation guide

Brand
Workrite Ergonomics
Model
Essentia Benching System
Type
Installation guide
Workrite Ergonomics | 800.959.9675 www.workriteergo.com 1 of 20
Worksurfaces
Grommet Kits
Parts Included, Benching System Parts Required, Ordered Separately
Assembly & Installation Instructions:
Essentia ES3E48-B02-WP-X Benching System,
Two Stations
Parts List Quantity
Included Two Stations
ESSENTIA FRAME SETS
ES3E30-48-X includes:
6608716-2PK-XX
4435511-XX
2
2Required/Included
ESSENTIA BENCH FOOT KIT, DUAL
ES-BFK48-X 1 Kit
(2 Feet) Required/Included
ESSENTIA PROGRAMMABLE SWITCH
ES-P-SWITCH 2 Required/Included
POWER MODULE, CIRCUIT 1, BLACK
ACC-PMC1-4P2U-B 2 Required/Included
POWER JUMPER BLOCK, BLACK
ACC-PWR-JBLOCK-B 1 Required/Included
POWER IN FEED CABLE
ACC-PWR-IN-HDWR-B 1 Required/Included
POWER CROSS CABLE
ACC-PWR-CCBL-24 1 Required/Included
54" BACK TO BACK CABLE
ACC-PWR-JBBCBL-54-B 1 Required/Included
CABLE TROUGH WITH END PLATES
ACC-CBLTRKIT-41-X 2 Included
Parts List Quantity Two Stations
WORKSURFACE
Benching - 29" Deep Only
T4629-XX-B3-XXXXXXX-XXX
(Options include width, grommet type, laminate
and edge band colors)
2Required/Order
Separately
GROMMET ONLY KIT
ACC-PWR-REMNT-X or
ACC-PWR-INMNT-X 2Required/Order
Separately
2 Station Essentia Benching System
2 of 20 Workrite Ergonomics | 800.959.9675 www.workriteergo.com
Workcenters
Trough
Benching
Foot Kit
Inlay Power
Grommets
Back to Back
Cable
Power In Feed
Recessed Power
Table of Contents
Step Page
You will assemble TWO complete Benching Workcenters joined by a pair of Benching
Feet.
Build Workcenters Page 3
ES3E30-48-S
Add Power & Recessed Mount Kit Page 10
ACC-PMC1-4P2U-B, ACC-PWR-JBLOCK-B, ACC-PWR-CCBL-24,
ACC-PWR-REMNT-X
Add Trough Page 14
ACC-CBLTRKIT-41-S
Add Benching Foot Kit Page 16
ES-BFK48-S
Add Inlay Mount Kit (if applicable) Page 17
ACC-PWR-INMNT-X
Install Grommets Page 18
ACC-PWR-REMNT-X or ACC-PWR-INMNT-X
Connect Back to Back Cable Page 18
ACC-PWR-JBBCBL-54-B
Connect Power Page 19
ACC-PWR-IN-HDWR-B
Adjust Glides Page 20
Initialize Legs Page 20
Workrite Ergonomics | 800.959.9675 www.workriteergo.com 3 of 20
Workrite Ergonomics | 800.959.9675 www.workriteergo.com 1 of 10
Box1: 6608716-2PK-01 Box2: 4435511-01
Parts Included, Frame Set
Required & Sold Separately
F 4 mm Allen Wrench
Qty: 1
L Power Cord
Qty: 1
I Cable Spool
Qty: 2
J " White Leg Cable Loops
Qty: 10
A Legs
Qty: 2 B Short Bracket
Qty: 4
H Control Box
Qty: 1
C Le End Bracket
Qty: 1
D Right End Bracket
Qty: 1
E #M6 × 12 mm Flat Head Cap Screw
Qty: 12
K #8 × ⅝" Pan Head Screw
Qty: 10
G #12 × ¾" Pan Head
Laminate Top Screw
Qty: 40
Assembly & Installation Instructions:
Essentia 2-Leg Workcenter ES2E30-48, ES3E30-48
Foot Kit
Basic or Programmable Switch
Top
2 of 10 Workrite Ergonomics | 800.959.9675 www.workriteergo.com
Verify that you have all the tools needed for the assembly
You will need the following tools:
#2 tip Phillips screwdriver or drill/driver
#3 tip Phillips screwdriver or drill/driver
M4 tip bit or 4mm Wrench (F)
If you do not have a Workrite worksurface, you will also need:
⅛" pilot drill bit
3⁄32" pilot drill bit
DANGER: To reduce the risk of electric shock, always unplug this Essentia Workcenter from the electrical outlet before
cleaning.
WARNING: To reduce the risk of burns, fire, electric shock, or injury to persons:
1. Unplug from outlet before putting on or taking o parts.
2. Close supervision is necessary when this furnishing is used by, or near children, invalids, or disabled persons.
3. Use this furnishing only for its intended use as described in these instructions. Do not use attachments not recommended by the
manufacturer.
4. Never operate this furnishing if it has a damaged cord or plug, if it is not working properly, if it has been dropped or damaged, or
dropped into water. Return the furnishing to a service center for examination and repair.
5. Keep the cord away from heated surfaces.
6. Do not use outdoors.
7. Do not operate where aerosol (spray) products are being used or where oxygen is being administered.
8. To disconnect, remove plug from outlet.
9. Each surface intended to support an equipment payload capacity of 225 pounds.
FOR COMMERCIAL USE ONLY
SAVE THESE INSTRUCTIONS
or
✓
IMPORTANT NOTE!
You must complete initialization (Step 12) at the end of
assembly or your workcenter WILL NOT FUNCTION PROPERLY.
4 of 20 Workrite Ergonomics | 800.959.9675 www.workriteergo.com
2 of 10 Workrite Ergonomics | 800.959.9675 www.workriteergo.com
Verify that you have all the tools needed for the assembly
You will need the following tools:
#2 tip Phillips screwdriver or drill/driver
#3 tip Phillips screwdriver or drill/driver
M4 tip bit or 4mm Wrench (F)
If you do not have a Workrite worksurface, you will also need:
⅛" pilot drill bit
3⁄32" pilot drill bit
WARNING: Maximum loading of table assembly is 225 lb. (102 kg). Maximum load includes the weight of the
table top itself, any equipment placed upon it, and any equipment suspended or hanging under it. Loading should be evenly distributed
over table surfaces. “Payload Capacity” is the Workrite Ergonomics recommended maximum loading which includes the Workrite sourced
worksurface.
Essentia 2-Leg
V = 120 VAC, 60 Hz / 8 A maximum
IMPORTANT SAFETY INSTRUCTIONS:
When using an electrical furnishing, basic precautions should always be followed, including the following:
Read all instructions before using this Essentia Workcenter.
DANGER: To reduce the risk of electric shock, always unplug this Essentia Workcenter from the electrical outlet before
cleaning.
WARNING: To reduce the risk of burns, fire, electric shock, or injury to persons:
1. Unplug from outlet before putting on or taking o parts.
2. Close supervision is necessary when this furnishing is used by, or near children, invalids, or disabled persons.
3. Use this furnishing only for its intended use as described in these instructions. Do not use attachments not recommended by the
manufacturer.
4. Never operate this furnishing if it has a damaged cord or plug, if it is not working properly, if it has been dropped or damaged, or
dropped into water. Return the furnishing to a service center for examination and repair.
5. Keep the cord away from heated surfaces.
6. Do not use outdoors.
7. Do not operate where aerosol (spray) products are being used or where oxygen is being administered.
8. To disconnect, remove plug from outlet.
9. Each surface intended to support an equipment payload capacity of 225 pounds.
FOR COMMERCIAL USE ONLY
SAVE THESE INSTRUCTIONS
or
✓
IMPORTANT NOTE!
You must complete initialization (Step 12) at the end of
assembly or your workcenter WILL NOT FUNCTION PROPERLY.
21
Workrite Ergonomics | 800.959.9675 www.workriteergo.com 5 of 20
Workrite Ergonomics | 800.959.9675 www.workriteergo.com 3 of 10
Layout Legs and Brackets
Check your cartons against the list on page 1 to
verify that you have all the parts needed.
Place Legs (A) and Brackets (B, C and D) on the
floor.
Attach Short & Medium Brackets
Attach Short Brackets (B) with
#M6×12mm Flat Head Cap Screws (E) to
both legs using 4 mm Allen Wrench (F).
Attach Right End Bracket (D) to sides of
the Leg (A) with Flat Head Cap Screws (E)
using 4 mm Allen Wrench (F). Attach Le
End Bracket (C) to sides of the other Leg
(A) with Flat Head Cap Screws (E) using 4
mm Allen Wrench (F).
Tighten securely.
Note: The right bracket will be on your
le and vice versa when the assembly is
seen upside down.
E#M6 × 12 mm Flat Head
Cap Screw
2
1B
B
B
B
C
D
To avoid stripping the threads, always
insert and make the first few turns
of the screw BY HAND with an Allen
wrench (F), ensuring it is in straight.
B
B
D
C
E
E
E
F
E
E
E
Le Leg
Right Leg
Right Bracket
Le Bracket
front
B
B
A
A
A
A
Hardware at actual size
Caution!
Only use the #M6 × 12 mm Flat Head
Cap Screw (E) for assembly. Use of
longer screws will damage legs.
6 of 20 Workrite Ergonomics | 800.959.9675 www.workriteergo.com
4 of 10 Workrite Ergonomics | 800.959.9675 www.workriteergo.com
Attach Base to Pre-Drilled Workrite Worksurface
If you have a non-Workrite worksurface skip to Step 4.
Note: For 2-Leg Corner and 120° Worksurface Mounting Instructions, go to: www.workriteergo.com/instructions
Position leg assemblies to align mounting holes in
brackets to pre-drilled holes in worksurface.
Attach at the four corner locations using #12 × ¾" Pan
Head Laminate Top Screws (G). If you use an electric
screwdriver, be sure it is on the lowest torque setting
to avoid stripping the holes in the top.
With frame set positioned and the four corner screws
secure, attach frame set using the remaining #12 × ¾"
Pan Head Laminate Top Screws (G).
Tighten securely.
Skip to Step 5.
3
G
G
G
G
3 screws per
Short Bracket
2 screws per End Bracket
(2 installed in Step 3b)
a
a
b
b
b
b
a
b
c
c
c
G #12 × ¾" Pan Head
Laminate Top Screw
Hardware at actual size
Workrite Ergonomics | 800.959.9675 www.workriteergo.com 7 of 20
Attach Control Box & Cable Spools to Worksurface
Position Control Box (H).
With Control Box (H) positioned over pilot holes, attach with two #12 × ¾" Pan Head Screws (G).
Attach Cable Spool (I) with the #12 × ¾" Pan Head Screw (G) to underside of worksurface. If you do not have a
Workrite worksurface, mount Cable Spools (I) in a convenient location between Legs and Control Box.
a
a
b
c
c
c
b
4
G
G
G
H
G
I
I
G #12 × ¾" Pan Head
Laminate Top Screw
Hardware at actual size
8 of 20 Workrite Ergonomics | 800.959.9675 www.workriteergo.com
Attach Cable Loops and Route Cables
Attach Black Switch Cable Loops to underside of worksurface using #12 × ¾" Pan Head Screws (G), making sure
to wrap the Cable Loop around the cable prior to attaching. If you do not have a Workrite worksurface, attach
cable loops in convenient locations between legs or switch and the control box. Attach White Leg Cable Loops
(J) to underside of worksurface using 12 × ¾" Pan Head Laminate Top Screw (G) as needed for your model.
Attach Programmable Switch
Position the Switch over the pilot holes near front edge of worksurface.
Attach Switch to underside of worksurface using the #8×⅝" Pan Head
Screws provided with your Programmable Switch.
#8 × ⅝" Pan Head
Screw
" White
Cable Loops (N)
on leg cables
⅛" Black Switch
Cable Loops and
screws from your
Workrite Switch
G
J
G #12 × ¾" Pan Head
Laminate Top Screw
Hardware at actual size
Note: #8 × ⅝" Pan Head Screw (K) are included for fastening the P-Loops,
but the #12 × ¾" Pan Head Laminate Top Screws will work better when
mounting P-Loops in the locations shown above.
front
b
a
a
b
Hardware provided with switch
at actual size
5
6
Workrite Ergonomics | 800.959.9675 www.workriteergo.com 9 of 20
Connect Leg Cables, Switch Cable and Power Cord to Control Box
Connect the Leg Cable (A) to the six position leg ports “M1” & “M2” on the Control Box (H).
Insert the Switch Cable into the switch port “HS” on the Control Box (H).
Insert the Power Cord (L) into the power port on the Control Box (H).
H
H
Leg Cable (A) into Leg Ports
“M1” & “M2”
Switch Cable into Switch
Port “HS”
Power Cord (L) in Power Port
b
a
c
b
a
c
7
L
L
A
A
Repeat for second workstation before continuing to next step.
10 of 20 Workrite Ergonomics | 800.959.9675 www.workriteergo.com
Workrite Ergonomics | 800.959.9675 www.workriteergo.com 1 of 8
or
or
Inlay Mount Kit Recessed Mount Kit
Power In Feed OptionsPower Jumper Cable
Required & Sold Separately
Optional & Sold Separately
Inlay Face Plate
Qty: 1
#8 × " Phillips Head
Screw - Black
Qty: 2
Cable Loop
Qty: 2
Recessed Face Plate
Qty: 1
Power In Cable, 96" Hardwire,
Dual Circuit
Qty: 1
Installation Manual
Qty: 1
Installation Manual
Qty: 1
Power In Cable, 96"QD Plug
Qty: 1
Wall Plate
Qty: 1
Mounting Tabs
Qty: 2
#10 × " Phillips Head
Screw - Black
Qty: 4
#10 × " Phillips Head
Screw - Black
Qty: 4
#6 × " Phillips Head
Screw - Black
Qty: 2
Grommet Cover
Qty: 1
Oval Grommet
Qty: 2 Oval Grommet
Qty: 2
"-20 Flange Nut-Silver
Qty: 2
¼"-20 Thumb Nut-
Black
Qty: 2
Back To Back Jumper
Cable, 54" - Black
Qty: 1
Side To Side Jumper
Cable, 50" - Black
Qty: 1
"-20 Flange Nut-Silver
Qty: 2
Jumper Block
Qty: 1
Power Cross Cable-Silver
24", 36" or 48"
Qty: 1
Assembly & Installation Instructions:
Benching Daisy Chain Power System
Benching Foot Kit, Benching Foot Connector Kit, Benching Worksurface, Switch
2-Leg Electric Essentia, Sierra HX or Sierra HXL Frameset (48" W / 60" W / 72" W × 30" D)
Cable Management Trough, Rigid Modesty Panel, Cable Management, Privacy/Sound Panels
ACC-PWR-INMNT-X
ACC-PWR-JSSCBL-50-B ACC-PWR-IN-HDWR-B ACC-PWR-IN-FFP-B
ACC-PWR-JBBCBL-54-B
ACC-PWR-REMNT-X
ACC-PWR-JBLOCK-B ACC-PWR-CCBL-XX
Circuit 2 Power Module
Qty: 1
Power Modules & Cables
Circuit 1 Power Module
Qty: 1
ACC-PMC1-4P2U-B
ACC-PMC1L-4P2U-B
ACC-PMC2-4P2U-B
ACC-PMC2L-4P2U-B
Required for 6, 8 and 10
desk Benching Systems
Workrite Ergonomics | 800.959.9675 www.workriteergo.com 1 of 8
or
or
Inlay Mount Kit Recessed Mount Kit
Power In Feed OptionsPower Jumper Cable
Required & Sold Separately
Optional & Sold Separately
Inlay Face Plate
Qty: 1
#8 × " Phillips Head
Screw - Black
Qty: 2
Cable Loop
Qty: 2
Recessed Face Plate
Qty: 1
Power In Cable, 96" Hardwire,
Dual Circuit
Qty: 1
Installation Manual
Qty: 1
Installation Manual
Qty: 1
Power In Cable, 96"QD Plug
Qty: 1
Wall Plate
Qty: 1
Mounting Tabs
Qty: 2
#10 × " Phillips Head
Screw - Black
Qty: 4
#10 × " Phillips Head
Screw - Black
Qty: 4
#6 × " Phillips Head
Screw - Black
Qty: 2
Grommet Cover
Qty: 1
Oval Grommet
Qty: 2 Oval Grommet
Qty: 2
"-20 Flange Nut-Silver
Qty: 2
¼"-20 Thumb Nut-
Black
Qty: 2
Back To Back Jumper
Cable, 54" - Black
Qty: 1
Side To Side Jumper
Cable, 50" - Black
Qty: 1
"-20 Flange Nut-Silver
Qty: 2
Jumper Block
Qty: 1
Power Cross Cable-Silver
24", 36" or 48"
Qty: 1
Benching Daisy Chain Power System
Benching Foot Kit, Benching Foot Connector Kit, Benching Worksurface, Switch
2-Leg Electric Essentia, Sierra HX or Sierra HXL Frameset (48" W / 60" W / 72" W × 30" D)
Cable Management Trough, Rigid Modesty Panel, Cable Management, Privacy/Sound Panels
ACC-PWR-INMNT-X
ACC-PWR-JSSCBL-50-B ACC-PWR-IN-HDWR-B ACC-PWR-IN-FFP-B
ACC-PWR-JBBCBL-54-B
ACC-PWR-REMNT-X
ACC-PWR-JBLOCK-B ACC-PWR-CCBL-XX
Circuit 2 Power Module
Qty: 1
Power Modules & Cables
Circuit 1 Power Module
Qty: 1
ACC-PMC1-4P2U-B
ACC-PMC1L-4P2U-B
ACC-PMC2-4P2U-B
ACC-PMC2L-4P2U-B
Required for 6, 8 and 10
desk Benching Systems
Verify that you have all the tools needed for the assembly
You will need the following tools:
#2 tip Phillips screwdriver or drill/driver
" Wrench
Benching Configurations
Part One Pair Two Pair Three Pair Four Pair Five Pair
Complete Workcenters 2 4 6 8 10
Must include benching feet and connector kits
Power Module
ACC-PMC1-4P2U-B 24345
ACC-PMC2-4P2U-B 00345
Jumper Block
ACC-PWR-JBLOCK-B 13579
Cross Cable
ACC-PWR-CCBL-XX 13579
Jumper Cables
ACC-JBBCBL-54-B 11111
ACC-JSSCBL-50-B 13579
Faceplate & Grommet Mount Kit
ACC-PWR-INMNT-X 2 4 6 8 10
or
ACC-PWR-REMNT-X 2 4 6 8 10
Power In Cable
ACC-PWR-IN-HDWR-B 11111
or
ACC-PWR-IN-FFP-B 11111
✓
☑
or and
All instruction quantities are per workcenter.
Workrite Ergonomics | 800.959.9675 www.workriteergo.com 11 of 20
2 of 8 Workrite Ergonomics | 800.959.9675 www.workriteergo.com
THIS ELECTRICAL SYSTEM IS UL CERTIFIED BY ETL FOR USE AS DESCRIBED BELOW. ALL SPECIFICATIONS
AND WARNINGS MUST BE FOLLOWED CLOSELY IN ASSEMBLY AND USE OF THIS SYSTEM.
CAUTIONS AND WARNINGS
WARNING: FAILURE TO FOLLOW CAUTIONS AND WARNINGS BELOW COULD RESULT IN ELECTRICAL SHOCK,
FIRE, PROPERTY DAMAGE, PERSONAL INJURY, OR DEATH.
CAUTIONS:
•Read Instructions: Read all warnings and installation instructions before installing and use
•Retain Instructions: Retain this instruction sheet for future use
•Wet Environment
· This system is designed for use indoors in a dry environment
· Never use this system in a wet environment
· Never allow liquids of any type to spill into the electrical system
•Follow Warnings: Read and follow all warnings and directions in this instruction sheet and marked on the components of the
system
•Service
· There are no serviceable parts contained in this system
· Do not open and or modify any parts used in this electrical system
WARNINGS:
•Risk of fire or electrical shock
· Do not electrically connect to more than one source of power supply
· Always verify the electrical system is only connected to one and only one source of power supply
•Power Entry Cable
· Route the Power Entry Cable where it will not be stepped on, pinched, have devices placed on it, or become a tripping hazard
· Never allow Power Entry Cable to sit in any liquid or get wet in any manner
•Power Cross Cables
· Secure the Power Cross Cables to the underside of the worksurface using P-Loops and screws provided
· Ensure the Power Cross Cables will not be pinched or have devices placed on them
· Never allow Power Cross Cables to sit in any liquid or get wet in any manner
•Power Jumper Cables: Side to Side or Front to Back
· Install Power Jumper Cables only when benching feet and foot connectors are installed and in use
· Ensure the Power Jumper Cables will not be pinched or have devices placed on them
· Never allow Power Jumper Cables to sit in any liquid or get wet in any manner
•Location: This system is intended for use indoors in a dry environment only
SYSTEM DESCRIPTION AND REQUIREMENTS: DAISY CHAIN POWER SYSTEM
•Limits & Restrictions
· Four wire system designed to operate using two dedicated 120 V, 60 Hz, 20 A circuits
· Power Modules o ered in Circuit 1 and Circuit 2 options
· Total power modules per four wire dual circuit system not to exceed 10 total modules (Maximum five each Circuit 1 and Circuit 2)
· The Daisy Chain Power System may only be installed in Workrite height adjustable workcenters that are connected with either Bench Feet (see
parts list) as back to back stations or as multiple bench systems using both Bench Feet and Bench Foot Connectors (see parts list)
•Assembly
· All assembly must be completed as outlined in the assembly instructions. All system parts must be used as supplied with no alterations or
modifications
•Connection/Power Entry
· Power Connection for power entry options o ered with this daisy chain power system must be connected by a commercial electrician
12 of 20 Workrite Ergonomics | 800.959.9675 www.workriteergo.com
4 of 8 Workrite Ergonomics | 800.959.9675 www.workriteergo.com
Install Power Jumper Block
Attach Power Jumper Block to underside of worksurface
using the four #10 × " Phillips Head Screws included
with the Power Jumper Block.
Note: No Power Jumper Block is used on last workcenter
with the daisy chain power system.
Connect Power Cross Cable
Connect the Power Cross Cable to the Jumper Block by inserting the plug into the
receptacle.
Note: Orientation of the plug to the receptacle is important and can
only connect one way. Make sure colored ports are aligned so the
colors match on the Power Module and Jumper Block.
Attach Cable Loops to underside of worksurface
using #8 × " Phillips Head Screw making sure
to wrap the Cable Loop around the cable prior to
attaching.
Note: No Power Cross Cable is
used on last workcenter with
the daisy chain power system.
1
2
a
a
b
b
b
4 of 8 Workrite Ergonomics | 800.959.9675 www.workriteergo.com
Install Power Jumper Block
Attach Power Jumper Block to underside of worksurface
using the four #10 × " Phillips Head Screws included
with the Power Jumper Block.
Note: No Power Jumper Block is used on last workcenter
with the daisy chain power system.
Connect Power Cross Cable
Connect the Power Cross Cable to the Jumper Block by inserting the plug into the
receptacle.
Note: Orientation of the plug to the receptacle is important and can
only connect one way. Make sure colored ports are aligned so the
colors match on the Power Module and Jumper Block.
Attach Cable Loops to underside of worksurface
using #8 × " Phillips Head Screw making sure
to wrap the Cable Loop around the cable prior to
attaching.
Note: No Power Cross Cable is
used on last workcenter with
the daisy chain power system.
1
2
a
a
b
b
b
8
9
Shown with ES3E30-48 Frameset.
Your Frameset will look dierent.
Workrite Ergonomics | 800.959.9675 www.workriteergo.com 13 of 20
Workrite Ergonomics | 800.959.9675 www.workriteergo.com 5 of 8
Install Recessed Power Module
If you have an Inlay Power Module, skip to Step 4
Attach Recessed Face Plate to underside of worksurface using the four #10 × " Phillips Head Screws included
with Recessed Face Plate.
Remove the two "-20 Flange Nuts from the studs on the Recessed Face Plate.
Using a " wrench, attach the Recessed Face Plate to the Power Module with the two "-20 Flange Nuts.
Connect the Power Cross Cable to the Power Module by inserting the plug into the receptacle.
Note: Orientation of the plug to the receptacle is important and can only connect one way. Make sure colored
ports are aligned so the colors match on the Power Module and Jumper Block.
Attach Benching Feet & Flip Benching Set Over
Align two workcenters back to back
Attach Feet according to instructions that came
with your Foot Kit.
Flip over Benching Set. Note: Flip over onto side
so you do not damage the control. Use at least
two people to flip over Benching Set.
IMPORTANT NOTE!
You must use benching feet. Flipping over benching sets takes
at least two people. CAUTION, HEAVY!
a
a
a
a
b
b
b
b
c
c
c
c
c
3
4
Flip onto side so you do
not damage the control.
10
Step 11.
Repeat for second workstation before continuing to next step. Power System will be completed aer
workcenters are flipped right side up.
14 of 20 Workrite Ergonomics | 800.959.9675 www.workriteergo.com
Workrite Ergonomics | 800.959.9675 www.workriteergo.com 1 of 2
Parts Included
Assembly & Installation Instructions:
Cable Trough, ACC-CBLTRKIT-XX-X
Attach Tough Ends to Cable Trough
Slide Trough Ends (B & C) onto Cable
Trough (A).
Attach from below using #10-32 × "
Pan Head Machine Screws (F). Repeat for
other side.
If Installing optional Rigid Modesty
Panel, skip to Step 2.
Attach from behind Trough using the
#10-32 × " Pan Head Machine Screws
(D) and the #10-32 Hex Nuts (E). Repeat
for other side.
A Cable Trough
Qty: 1 B Le Trough
End
Qty: 1
C Right Trough
End
Qty: 1 G #12 × " Pan Head
Wood Screw
Qty: 8
Verify that you have all the tools needed for the assembly
#2 tip Phillips screwdriver over 6" long
or drill/driver with extension
" wrench if needed for Hex Nut (E)
or
Optional & Sold Separately
Daisy Chain Power System, Rigid Modesty Panel
41", 53" or 65" long
D#10-32 × " Pan Head
Machine Screws
Qty: 8
E#10-32 Hex Nut
Qty: 4
F #10-32 × " Pan Head
Machine Screws
Qty: 2
+6"
+6"
+6"
+6"
1
B
C
A
✓
a
a
a
c
c
b
b
D
E
F
Trough only installation
11
per workcenter
Workrite Ergonomics | 800.959.9675 www.workriteergo.com 15 of 20
Workrite Ergonomics | 800.959.9675 www.workriteergo.com 2 of 2
1500283 Rev B
Attach Cable Trough to Underside of Worksurface
Align holes in Cable Trough with holes
in bottom of your Workrite pre-drilled
worksurface.
Attach Trough assembly using the #12 × "
Phillips Pan Head Screws (G). Access holes
provide easy attachment with long screwdriver.
Under Benching Worksurface with optional Rigid Modesty Panel
& Daisy Chain Power System
Attach Tough Ends to Cable Trough With Optional Rigid Modesty Panel
Skip this step unless you've purchased the Rigid Modesty Panel ACC-MODPNL-XX-B3
Attach Trough (A) to the threaded inserts
on the Rigid Modesty Panel from inside
Trough using the eight #10-32 × " Pan
Head Machine Screws (D).
3
a
b
2G
Access hole
A
D
Optional Rigid Modesty Panel
ACC-MODPNL-XX-B3
12
Repeat for second workstation before continuing to next step.
Shown with ES3E30-48 Frameset.
Your Frameset will look dierent.
16 of 20 Workrite Ergonomics | 800.959.9675 www.workriteergo.com
Workrite Ergonomics | 800.959.9675 www.workriteergo.com 1 of 2
Parts Included
Assembly & Installation Instructions:
Essentia Benching Foot Kit, ES-BFK48-X
A Benching Feet with Glides
Qty: 2 B #M6 × 18 mm Flat
Head Cap Screw
Qty: 16 D Hole Plug
Qty: 20
C 4 mm Allen Wrench
Qty: 1
Verify that you have all the tools needed for the assembly
4 mm Allen Wrench (C) supplied
Note!
Only use the #M6 × 18 mm Flat Head
Cap Screw (B) supplied with the
Benching Foot Kit to attach feet.
Fill outside facing foot holes with Hole Plugs (D). If you are building a Benching
System with multiple side by side workcenters, wait until you've completed
joining your workcenter pairs before adding Hole Plugs.
Flip over Benching Set. Note: Flip over onto side so you do not damage the
control. Use at least two people to flip over Benching Set.
Attach Sierra Benching Feet
Align two workcenters back to back
Attach Feet (A) using Allen Wrench (C) and the #M6
× 18 mm Flat Head Cap Screws(B).
Parts Included
B #M6 × 18 mm Flat Head
Cap Screw
Hardware at actual size
✓
a
b
1
c
d
d
a
b
C
B
B
B
A
A
B
D
D
D
D
Flip onto side so you do
not damage the control!
c
Caution! Heavy!
Flipping over benching sets takes at least two people. CAUTION,
HEAVY! Flip over onto side so you do not damage the control.
13
Workrite Ergonomics | 800.959.9675 www.workriteergo.com 17 of 20
Install Grommets
For both Inlay Mount Kit and Recessed
Mount Kit, place Oval Grommets into oval
cutouts in Worksurface
For Recessed Mount Kits, place the
Grommet Cover into rectangular cutout and
lock in place with two #6 × " Phillips Head
Screws.
Install Inlay Power Module
If you've installed a Recessed Power Module, skip to Step 6.
Remove the two "-20 Flange Nuts from the studs on the Inlay Face Plate.
Using a " wrench, attach the Inlay Face Plate to the Power Module with the two "-20 Flange Nuts.
Insert Power Module and Face Plate assembly into cutout in Worksurface.
From below the worksurface, slide the two Mounting Tabs onto the threaded posts from the Face Plate and
secure in place using two ¼"-20 Thumb Nuts.
Connect the Power Cross Cable to the Power Module by inserting the plug into the receptacle.
Note: Orientation of the plug to the receptacle is important and can only connect one way. Make sure colored
ports are aligned so the colors match on the Power Module and Jumper Block.
6
5
a
a
b
b
c
c
d
d
a
a
a
bb
Below
Below
Workrite Ergonomics | 800.959.9675 www.workriteergo.com 1 of 8
or
or
Inlay Mount Kit Recessed Mount Kit
Power In Feed OptionsPower Jumper Cable
Required & Sold Separately
Optional & Sold Separately
Inlay Face Plate
Qty: 1
#8 × " Phillips Head
Screw - Black
Qty: 2
Cable Loop
Qty: 2
Recessed Face Plate
Qty: 1
Power In Cable, 96" Hardwire,
Dual Circuit
Qty: 1
Installation Manual
Qty: 1
Installation Manual
Qty: 1
Power In Cable, 96"QD Plug
Qty: 1
Wall Plate
Qty: 1
Mounting Tabs
Qty: 2
#10 × " Phillips Head
Screw - Black
Qty: 4
#10 × " Phillips Head
Screw - Black
Qty: 4
#6 × " Phillips Head
Screw - Black
Qty: 2
Grommet Cover
Qty: 1
Oval Grommet
Qty: 2 Oval Grommet
Qty: 2
"-20 Flange Nut-Silver
Qty: 2
¼"-20 Thumb Nut-
Black
Qty: 2
Back To Back Jumper
Cable, 54" - Black
Qty: 1
Side To Side Jumper
Cable, 50" - Black
Qty: 1
"-20 Flange Nut-Silver
Qty: 2
Jumper Block
Qty: 1
Power Cross Cable-Silver
24", 36" or 48"
Qty: 1
Assembly & Installation Instructions:
Benching Daisy Chain Power System
Benching Foot Kit, Benching Foot Connector Kit, Benching Worksurface, Switch
2-Leg Electric Essentia, Sierra HX or Sierra HXL Frameset (48" W / 60" W / 72" W × 30" D)
Cable Management Trough, Rigid Modesty Panel, Cable Management, Privacy/Sound Panels
ACC-PWR-INMNT-X
ACC-PWR-JSSCBL-50-B ACC-PWR-IN-HDWR-B ACC-PWR-IN-FFP-B
ACC-PWR-JBBCBL-54-B
ACC-PWR-REMNT-X
ACC-PWR-JBLOCK-B ACC-PWR-CCBL-XX
Circuit 2 Power Module
Qty: 1
Power Modules & Cables
Circuit 1 Power Module
Qty: 1
ACC-PMC1-4P2U-B
ACC-PMC1L-4P2U-B
ACC-PMC2-4P2U-B
ACC-PMC2L-4P2U-B
Required for 6, 8 and 10
desk Benching Systems
14
Step 15.
, (continued)
18 of 20 Workrite Ergonomics | 800.959.9675 www.workriteergo.com
Connect Back to Back Cable
Connect the 54"Back to Back Jumper from
the Jumper Block on one workstation to
the Power Module on the next workstation
to the back.
Note: Orientation of the plug to the
receptacle is important and can only
connect one way. Make sure colored ports
are aligned so the colors match on the
Power Module and Jumper Block.
6 of 8 Workrite Ergonomics | 800.959.9675 www.workriteergo.com
Install Grommets
For both Inlay Mount Kit and Recessed
Mount Kit, place Oval Grommets into oval
cutouts in Worksurface
For Recessed Mount Kits, place the
Grommet Cover into rectangular cutout and
lock in place with two #6 × " Phillips Head
Screws.
6
a
a
a
bb
Below
15
16
Workrite Ergonomics | 800.959.9675 www.workriteergo.com 19 of 20
Connect Power In Feed to Power Module
Connect your Power In Cable to the
Power Module.
Note: Orientation of the plug to the
receptacle is important and can
only connect one way. Make sure
colored ports are aligned so the
colors match on the Power In Cable
and Power Module.
Plug In Workcenters to Power Module
Connect your Workcenter Power Cable to the Power Module. Choose one of the convenient Power Module
power receptacles in the Tough area under the worksurface. Wrap any unused cable around one of the cable
spools or lay in Trough if necessary.
Repeat for second workcenter.
Workcenter power
Under Worksurface
17
18
20 of 20 Workrite Ergonomics | 800.959.9675 www.workriteergo.com
#1500337 Rev C
Connect Power In Feed to the Power Supply
Note: This step should only be performed by a professional
licensed electrician.
Based on the National Electric Code (NEC) Article 220-14,
receptacle outlets shall be calculated at 180 VA per duplex.
Workrite electrical products are rated for use in 120 V
systems which yield a duplex rating of 1.5 A. Because most
applications actual circuit usage is variable or unknown, we
recommend using a max circuit rating of 80% as a guide to
determine how many receptacles should be connected per
circuit. This translates into 8 duplex or 16 simplex outlets on
a 15 AMP circuit and 10 duplex or 20 simplex outlets on a 20
AMP circuit.
Some local codes may vary from the NEC code therefore
these are only recommendations and local codes should
always be checked and followed.
Initialize Legs
Aer all Legs and Switches are connected, and the Power In Feed has been plugged in, hold the down arrow
on the Switch until the Legs make a short motion down and then back up. This initializes and synchronizes the
workcenter Legs.
Adjust Feet Glides
If necessary, adjust Leveling Glides on workcenter feet to level the worksurface. Unscrew to increase height,
screw in to decrease height.
You must complete this
initialization step or your
workcenter will NOT
function properly.
Hold down the down arrow until
workcenter moves slightly upwards!
Repeat for all Workcenters.
Cleaning Instructions
To clean the Essentia legs, apply cleaner to a so cloth.
Suggested cleaners: Windex or Formula 409.
Do not use solvents and do not saturate or spray cleaners directly onto workcenter base.
Parts & Accessories
Visit http://workriteergo.com/documentation/other/workrite_ergonomics_pricing_specification_guide.pdf for
replacement parts.
8 of 8 Workrite Ergonomics | 800.959.9675 www.workriteergo.com
#1500281 Rev C
Connect Power In Feed
Connect your 96" Power In Cable
from the Power Module to the
power source.
Note: Orientation of the plug to the
receptacle is important and can
only connect one way. Make sure
colored ports are aligned so the
colors match on the Power In Cable
and Power Module.
Connect to the power source.
(see warning below.)
WARNING!
Always install the Power In Feed as the last step when assembling a Benching System Power Module System.
Power connection for power entry options off ered with this daisy chain power system must be connected by
a commercial electrician.
Do not electrically connect to more than one source of power supply.
Always verify the electrical system is connected to one and only one source of power supply.
10
a
a
b
b
19
20
21
✓
✓
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20

Workrite Ergonomics Essentia Benching System Installation guide

Brand
Workrite Ergonomics
Model
Essentia Benching System
Type
Installation guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents