NCR MSR Series Kit Instructions

NCR
Brand
NCR
Model
MSR Series
Category
Signal cables
Type
Kit Instructions

This manual is also suitable for

NCR MSR Series

NCR MSR Series is a magnetic stripe reader/writer device that mounts on the side of the 7409 Display Head. It is available in two versions: JIS MSR (7409-K227) and ISO MSR (7409-K229). The device is capable of reading and writing data to magnetic stripe cards, and it can be used in a variety of applications, including:

  • Retail: NCR MSR Series can be used to process payments, loyalty cards, and gift cards.
  • Hospitality: NCR MSR Series can be used to check in guests, process payments, and issue room keys.
  • Healthcare: NCR MSR Series can be used to identify patients, process payments, and dispense medications.

NCR MSR Series

NCR MSR Series is a magnetic stripe reader/writer device that mounts on the side of the 7409 Display Head. It is available in two versions: JIS MSR (7409-K227) and ISO MSR (7409-K229). The device is capable of reading and writing data to magnetic stripe cards, and it can be used in a variety of applications, including:

  • Retail: NCR MSR Series can be used to process payments, loyalty cards, and gift cards.
  • Hospitality: NCR MSR Series can be used to check in guests, process payments, and issue room keys.
  • Healthcare: NCR MSR Series can be used to identify patients, process payments, and dispense medications.
7409-K227/K229
MSR
Kit Instructions
Issue A
Revision Record
Issue
Date
Remarks
A
Feb 2013
First issue
1
Introduction
This kit provides an MSR module that mounts on the side of the 7409 Display Head.
There are two versions:
• JIS MSR (7409-K227)
• ISO MSR (7409-K229)
32011
2
Installation Procedures
Warning: Disconnect the AC power cord before disassembling the Terminal.
1. Remove the Display Head from its mount.
Removing the 7409 from the Table Top Mount
a. Release the Mounting Plate Latches and tilt the display back. Relock the
latches.
26901
Mounting Plate Latches
3
b. Loosen the captive screw that secures the Cable Cover and remove the cover.
26690
Cable Cover Captive Screw
c. Disconnect the cables from the I/O Panel.
4
d. Release the Mounting Plate Latches and remove the 7409 from the mount.
26659
Mounting Plate Latches
Baseplate
Removing the 7409 from the Fixed Angle Mount
a. Remove the screws (2) in the sides of the Fixed Angle Mount.
26681
Screw
(One on each side)
5
b. Rest the bottom of the display on the Display Support.
26680
Display Support
Cable Cover Captive Screw
Note: Place the Display Support behind the extension on then Display Hinge
Bracket.
24753
Display Support
Bracket Extension
c. Loosen the captive screw that secures the Cable Cover and remove the cover.
6
d. Disconnect the cables from the I/O Panel.
Note: The Power Cable connector locks into position when connected to the
terminal and cannot be removed by simply pulling on the cable. You must
grasp the connector and slide the outside housing out from the terminal to
unlock it from the terminal connector.
e. Slide the Locking Brackets (2) to the unlocked position.
7
f. Remove the display from the Fixed Angle Mount.
24629
g. Disconnect the Power Cord from the I/O Panel on the terminal.
2. Lay the terminal face down on a flat surface.
3. Loosen the captive screws (2) that secure the Rear Cover.
26903
Captive Screws
Rear Cover
8
4. Pivot the Rear Cover to the open position.
26651a
Rear Cover Latches
5. Remove the Rear cover by squeezing the Rear Cover Latches together as indicated
above.
9
6. Remove the No MSR Cover (2 screws).
26902
No MSR Cover
7. Insert the cables into the opening in the chassis and install the MSR Assembly in
the slots of the cabinet.
32013
MSR
8. Secure the MSR to the chassis (2 screws).
10
9. Connect the MSR USB Cable to the I/O Board.
10. Connect the MSR Ground Cable to the chassis (screw).
26691
MSR Data Cable
MSR Ground Cable
11. Replace the Rear Cover and mount the Display Head to its mount using the
reverse procedures.
11
MSR Programming
If the MSR Module (ISO) is replaced the customer is responsible for re-programming
the device to custom wedge-emulation parameters, using the NCR MSR
Configuration Utility, which is available on the NCR website at:
http://www.ncr.com
1. At this site, select the Support tab.
2. Select Drivers and Patches → Retail Support Files → NCR RealPOS and
SelfServ Terminal and Operating Systems → NCR RealPOS 25 (7610) →
Windows →[Operating System].
3. Select the MSR Configuration Utility.
For information about how to use the utility see the NCR MSR Configuration Utility
User Guide (B005-0000-2031).
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13

NCR MSR Series Kit Instructions

NCR
Brand
NCR
Model
MSR Series
Category
Signal cables
Type
Kit Instructions
This manual is also suitable for

NCR MSR Series

NCR MSR Series is a magnetic stripe reader/writer device that mounts on the side of the 7409 Display Head. It is available in two versions: JIS MSR (7409-K227) and ISO MSR (7409-K229). The device is capable of reading and writing data to magnetic stripe cards, and it can be used in a variety of applications, including:

  • Retail: NCR MSR Series can be used to process payments, loyalty cards, and gift cards.
  • Hospitality: NCR MSR Series can be used to check in guests, process payments, and issue room keys.
  • Healthcare: NCR MSR Series can be used to identify patients, process payments, and dispense medications.
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents