NCR MSR 7610-K151 Kit Instructions

Brand: NCR

Model: MSR 7610-K151

Type: Kit Instructions

This manual is also suitable for

MSR 7610-K142

7610‐K151

MSRw/Biometric

FingerprintReader

KitInstructions



IssueA

Revision Record

Issue Date Remarks

A Feb2011 Firstissue

 

Introduction

Thiskitprovidesa3‐trackISOMSRw/DigitalPersonaHDbiometricfingerprint

readerassemblythatmountsonthesideofthe7610/11.



Installation Procedures

Warning: DisconnectthepowerbeforedisassemblingtheTerminal.

1. DisconnectthePowerCable.

ThePowerCableconnectorlocksintopositionwhenconnectedtotheterminaland

cannotberemovedbysimplypullingonthecable.Youmustgrasptheconnector

andslidetheoutsidehousingoutfromtheterminaltounlock

itfromtheterminal

connectortoremoveit.

29249a

Terminal Power Cable



2. RemovetheTableTopStand.

a. Laytheterminalfacedownonaflatsurface.

Caution: Thefrontbezelisapaintedcomponentandtheweightofthe

terminalcancauseabrasionswhenmovedaroundonasurface.Alwaysusea

softmaterial(cloth,foam)toprotectthebezelwhen

placingtheterminalface

down.

b. Loosenthecaptivethumbscrews(2)thatsecuretheTableTopStand.

241

Protective Foam or Cloth



c. SlidetheTableTopStandasshowntodisengagetheslotsintheTableTop

StandfromtheMountingStudsonthebackoftheterminal.

39a

Mounting

Slots

Mounting

Studs



3. RemovetheRearCover(loosenthecaptivescrews(4)thatsecureittothechassis.)

29287

Captive Screws



4. RemovetheNoMSRCover.Placeyourtwoind exfingersintheFingerSlotsand

prytheedgeoftheNoMSRCoverfromtheterminalchassisasshown.Liftthe

coverfromtheterminal.

Finger Slots

No MSR Cover



5. Loosenthecaptivescrews(2)andremovetheMSRCover.

29403



6. InstalltheMSRAssemblyontheterminalcabinet(2screws).SecuretheMSR

GroundWireunderoneofthescrews.

29285

MSR Screws

Ground Wire



7. ConnecttheMSRCabletotheTouchControllerBoard.

8. ConnecttheBiometricsCabletotheTouchControllerBoardandtheMotherboard.

9. InstalltheMSRCover(2captivescrews).

MSR Cable

Biometrics Cables

MSR Cover



10. ReplacetheRearCover(4captivescrews).

411



11. ReplacetheterminalontheTableTopStand.

MSR Programming

IftheMSRModuleisreplacedthecustomerisresponsibleforre‐programmingthe

devicetocustomwedge‐emulationparameters,usingtheNCRMSRConfiguration

Utility,whichisavailableontheNCRwebsiteat:

http://www.ncr.com

1. Atthissite,selecttheSupporttab.

2. SelectDrivers and Patches→Retail Support Files→NCR RealPOS and

SelfServ Terminal and Operating Systems→NCR RealPOS 25 (7610)→

Windows→MSR Configuration Utility.

ForinformationabouthowtousetheutilityseetheNCRMSRConfigurationUtility

UserGuide(B005‐0000‐2031).

NCR MSR 7610-K151 Kit Instructions

Brand: NCR

Model: MSR 7610-K151

Type: Kit Instructions

This manual is also suitable for

MSR 7610-K142

Download PDF

report

NCR MSR 7610-K151 Kit Instructions

This manual is also suitable for

NCR MSR 7610-K151 Kit Instructions

Related papers