Before you Start …
Build the unit close to where it will be used. Handle all items carefully. Always lay panels
down on a flat smooth surface. Complete each stage before moving onto the next one.
Follow these guidelines and take your time.
If any parts are missing, please call the Helpline on 01769 575500 and our team will get
things sorted.
Cross Head Screwdriver
Drill
Level
2.5mm
Drill Bit
5mm
Drill Bit
1 x RH Side Panel
1 x LH Side Panel
1 x Back Panel
4 x Rail
2 x Plinth
1
2
3
4
5
Panels & Drawers Hardware
ASSEMBLY GUIDE
Minimum Tools Required
Hammer
CHEST
2 DRAWER
2 x
A
16 x
C
6 x
B
4 x
F
Fitted
Bedroom
Range
16 x
G
12 x
I
Flat Head Screwdriver
Please use scissors to open the
bag of fittings and then empty
the contents into a bowl, so
that they do not get lost!
2 x
L
12 x
O
Handles, Handle screws & Drawer fronts are to be
supplied independently and not covered by this guide.
20 x
D
PLEASE keep all fittings away from young children
Bradawl
Scissors
Tape Measure
450mm
1
2
3
4
4
4
4
5
5
15mm
4 x
12mm
AE
2 x
AF
2 x
AG
2 x
AH
2 x
4 x
8 x
X
2 x RH Drawer Side
2 x LH Drawer Side
2 x Drawer Back
2 x Drawer Base
7
8
9
11
25mm
45mm
25mm
45mm
7
8
9
11
AK
2 x
AP
AN
2 x
AR
4 x
AS
1
3
2
Carefully fit parts and to
panel , and then fit 2 x
drawer runner , and 2 x soft
close mechanism , using
screws .
F551
Tight
against
panel
F139
Tight
against
panel
G
2
G
G
(LH Side Panel Shown)
I
I
I
G
G
I
Fit panels and to panel , as shown.
2
4
4
4
4
5
5
1
Then fit Cams as
shown, ensuring
that the arrow is
pointing towards
panel , and tighten
clockwise.
O
2
2
4
4
4
4
5
5
Now fit panel to panels and .
I
G
G
I
Now repeat for panel , but
replace drawer runner with
drawer runner , and soft
closer , with soft closer .
G I
2
AE
D
CL
AE
D
1
AE
AG
AP
AE AE
2
4
5
1 4 5
Insert the Cams as
above, but with the
arrows pointing
towards panel ,
and tighten
clockwise.
1
TOP OF PANEL
AP
AR
4
Joining Units
5
Slide the back panel colour-side facing down,
along the grooves in the side panels. Secure the
back in place using screws as shown.
Panel protectors should be fitted, prior to
standing the unit up. Fit 2 x to the bottom of
each side panel, approximately 50mm in from
front and back, as shown.
Now you can stand the unit up.
6
F
F
B
B
B
3
3
B
F
F
Starting in a corner make sure the first unit is level. Push the next unit up against the
first unit, and level. Check the sides are flush, and in line, and then clamp them together.
Pick two points, roughly in the middle of one side panel, towards the top and bottom of
the unit, and drill through into the adjoining side panel.
Now push connector into these holes, and then screw bolt in from the other side
and tighten with a screwdriver to secure.
L A
B
B
B
F
F
will be on the
outside surface of the
Right Drawer Side.
Construction of Drawers
Before fitting the Cam Legs to your Drawer Fronts you will have to drill the holes required for the Handles
you have purchased separately. Drill through the appropriate pilot hole(s) for the Handles you have
purchased.
We do not recommend the use of Power Screwdrivers as they can too easily drive the Screws at an angle
causing them to breakout of the panel, and it is too easy to over tighten the Screws and strip the threads
formed in the chipboard.
PILOT HOLES.
From the REAR FACE of the Drawers drill through the
holes using a 2.5mm diameter drill. From the FRONT
FACE of the Drawers, open out the 2.5mm diameter
holes using a 5mm drill. Screw Handles to Drawer Fronts.
Screw the Cam Legs into the holes shown.
X
GG
G
X
X
X
8
9
9
8
9
Fit the LH , and RH , drawer sides to the drawer back , using screws as shown.
Now slide the drawer base into place as shown.
8
9
X
11
will be on the outside surface of the Left Drawer Side.
Then fit cams into panels
and , as shown, ensuring
that the arrow is pointing
towards the drawer front.
9
7
8
8
7
Now fit the drawer front onto
drawer sides and , and
tighten cams clockwise.
8 7
AN
AN
AN
AN
11
11
7
7
7
7
B&Q plc, Chandlers Ford, Hampshire, SO53 3YX.
Visit us at www.diy.com
That’s the 2 Drawer Chest completed
Take care of your unit by using a damp cloth to clean it.
Fit the Hinge Covers F306
over the Hinges.
Recycling – the packaging materials for this
product may be recycled through your local
recycling centre. When you want to dispose of
the product itself, please consider donating it
to a local charitable organisation, otherwise
recycle it through your local recycling centre.
F676
Recycling – the packaging materials for this product may be recycled through your local recycling centre. When you want to dispose of
the product itself, please consider donating it to a local charitable organisation. Otherwise, recycle it through your local recycling centre.
10
Fitting of Plinth
The plinth should be cut to the required length, allowing for the
mitre joint, and then stuck onto the unit, using a suitable adhesive.
11
Fitting of Top Panel
Note: Plinths are supplied separately. If you are in any doubt
about fitting these items, you should seek advice from an expert.
7
Fitting of Drawer Runners To Drawers
Position each runner onto drawer bottom, as shown,
flush to the back of the drawer front. Then use a
bradawl to mark the two holes as indicated.
Secure with screws , as shown.
C
C
C
C
C
9
11
7
AF
AH
Fitting of Drawers to Unit
9
Turn the drawer over and locate the wheels on
the drawer over the wheels fitted in the unit and
push into position.
In order to secure the top panel, the drawers
should first be removed from the unit.
Then, once the top is in the correct position,
carefully clamp it in place, and then screw
through from the underside of the top rail,
using screws .
Now replace the drawers.
AK
AK
Fitting of Soft Close Bracket to Drawer Sides
8
The soft close brackets should be
fitted to both of the drawer sides,
using screws as shown.
C
9
11
7
AS
CSS1359 01/10
/
