Argos Adult Malibu 558/2255 Assembly Instructions Manual

Brand
Argos
Model
Adult Malibu 558/2255
Type
Assembly Instructions Manual

This manual is also suitable for

MADE IN
BRITAIN
Dimensions
If you need help or have damaged or missing parts, please visit www.argos-support.co.uk
or email: Help@ClickSpares.co.uk (quoting your original order number)
Alternatively, call the Spares Helpline on: 0370 112 1928.
For any other queries please contact the Customer Helpline on: 0345 640 2020
Important - Please read these instructions fully before starting assembly
More help is available throughout this booklet by scanning
in the QR codes or typing in the links
Adult Malibu - 4 Drawer 3 Door Robe
Assembly Instructions - Please keep for future reference
532/8038
544/3985
563/7038
544/3930
563/6307
564/9581
565/5429
542/1639
558/2255
548/2458
Width - 110.4cm
Depth - 49.8cm
Height - 180.5cm
Issue 1 - 02/06/16
Safety and Care Advice
Important - Please read these instructions fully before starting assembly
• Warning: This unit weighs
approximately 83kgs.
Please lift with care.
• Check you have all the
components and tools listed on
pages 2 to 5.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Parts of the assembly will be
easier with 2 people.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close to
its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor (use opened
out unit carton).
1
Care and maintenance
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
Note: If required the next page
can be cut out and used as
reference throughout the
assembly. Keep this page with
these instructions for future
reference.
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Safety note: To prevent
possible overbalancing this unit
must be secured to a wall
using the overbalance protector
kit supplied or, an alternative
fixing method of your choice.
• Dispose of all packaging
carefully and responsibly.
Components - Panels
If you need help or have damaged or missing parts, please visit www.argos-support.co.uk
or email: Help@ClickSpares.co.uk (quoting your original order number)
Alternatively, call the Spares Helpline on: 0370 112 1928.
For any other queries please contact the Customer Helpline on: 0345 640 2020
Please check you have all the panels listed below
When applicable, remove any
protective film before use
2
Horizontal
(DF7351)
(106.95 x 47.4cm)
8
1 2Left Drawer
Front
(DF7359)
(53 x 15.7cm)
x 2
Right Drawer
Front
(DF7362)
(53 x 15.7cm)
x 2
3 Left Drawer
Side
(WB450-130LH)
(45 x 13cm)
x 4
Right Drawer
Side
(WB450-130RH)
(45 x 13cm)
x 4
4
Drawer Back
(W478-130)
(47.8 x 13cm)
x 4
5
Drawer Base
(T489-447)
(48.9 x 44.7cm)
x 4
6 Top
(DF7347)
(110.35 x 49.8cm)
7
Wide Shelf (DF7363)
(71.4 x 47cm)
9
Loose Shelf (DF7364)
(34.05 x 47cm)
x 3
10
Drawer Divider
(DF7352)
(32.35 x 47.2cm)
14Left Side
(DF7348)
(179 x 49.6cm)
11 Right Side
(DF7349)
(179 x 49.6cm)
12 Divider
(DF7350)
(134.4 x 47.2cm)
13
3
Components - Panels
If you need help or have damaged or missing parts, please visit www.argos-support.co.uk
or email: Help@ClickSpares.co.uk (quoting your original order number)
Alternatively, call the Spares Helpline on: 0370 112 1928.
For any other queries please contact the Customer Helpline on: 0345 640 2020
Please check you have all the panels listed below
When applicable, remove any
protective film before use
15 Plinth
(DF7353)
(106.95 x 9.2cm)
16 Large Top Rail
(DF5858)
(71.4 x 6cm)
17 Small Top Rail
(DF7356)
(34.05 x 6cm)
18 Front Cross Rail
(DF7354)
(106.95 x 9.2cm)
Long Hanging Rail (FHR708)
(70.8cm long)
23
21 Left Door
(DF7357)
(135.6 x 35.25cm)
22 Right Door and Middle Door
(DF7357)
(135.6 x 35.25cm)
x 2
19 Back Cross Rail
(DF7355)
(106.95 x 9.2cm)
20 Back Rail
(DF5866)
(71.4 x 9.2cm)
24 Small Back
(X1709-360)
(170.9 x 36cm)
x 2
25 Large Back
(X1709-733)
(170.9 x 73.3cm)
Please check you have all the fittings listed below
Components - Fittings
If you need help or have damaged or missing parts, please visit www.argos-support.co.uk
or email: Help@ClickSpares.co.uk (quoting your original order number)
Alternatively, call the Spares Helpline on: 0370 112 1928.
For any other queries please contact the Customer Helpline on: 0345 640 2020
Ruler - Use this ruler to help correctly identify the screws
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
4
Drawer Fittings Bag marked ‘drw kit’
A
Quickfit dowel
(F545) x 8
C
Knock-in Peg
(F171GY) x 16
D E
19mm
Screw (F461) x 7
Large locking cam nut (F607) x 8
B
13mm Screw (F79) x 8
13mm Screw (F63) x 16
F
IH
9mm Screw (F73) x 24
Main Fittings Bag
A
Quickfit dowel
(F545) x 22
N
Wooden dowel (F22) x 41
J
Nail (F51) x 35
K
B
L
Rail Holder (F891) x 2
M
Plastic Nail (F91) x 6
G
F
13mm Screw
(F63) x 8
Door Buffer (F137) x 6
Large locking cam nut (F607) x 22
P
O
Large wooden dowel
(F40) x 2
40mm Screw
(F910) x 4
R
Back holder (F276) x 5
Q
Nail screw
(F277) x 5
13mm Screw (F52) x 4
Shelf stud (F110) x 12
Components - Fittings
5
Individual Fittings Bags
U
T
Handle
(F418) x 7
Pre-mounted
hinge (
F419) x 9
436mm long
Drawer Brace (F427) x 4
V
M
W
CR Runner
(F609) x 4
b
DL Runner
(F610) x 4
W
c
CL Runner
(F608) x 4
W
a
DR Runner
(F611) x 4
W
d
450mm long
CR
CL
DR
DL
Overbalance protector
kit (
F474) x 1
S
Rule
Tools required
Rule
ScissorsSquare
Spirit
level
Hammer Bradawl
Eye protection
(when using a
hammer or drill)
Cross-head
screwdriver
Step
ladder
Electric drill
(only use
when drilling
into walls)
6
Step 1
Assembly Instructions
Step 2
Fit the drawer sides
to the 4 drawer fronts
Push the left drawer
sides . and right
drawer sides . down
onto the back of the 2
left drawer fronts and
2 right drawer fronts .
Turn the large locking
cam nuts clockwise
as far as they will go to
secure the panels.
Important: Make sure
there is no gap between
the fitted panels.
3
1
2
4
Prepare the 4 pair of
drawer sides
a: Insert a large locking
cam nut into the 4 left
drawer sides and the
4 right drawer sides .
Note: The arrow on the
locking cam nut must
point towards the
hole in the end of the
panel.
b: Push 1 of the quickfit
dowels as far as it will
go into the left drawer
sides and the right
drawer sides .
Note: Only the plastic
thread of the quickfit
dowel sticks out from the
panel.
A
3
4
B
3
4
x 2
11
4
B
B
a:
b:
B
x 4 x 4
3
4
B
B
A
x 4 x 4
3
4
A
A
Use the Drawer Fittings Bag marked ‘drw kit’ for Steps 1 - 7
3
x 2
11
4
3
hps://www.youtube.com/watch?v=HclfJdkm-Lg
Standard Drawer Box Assembly
1 2
Note: The 2 right drawer fronts
have a small identification hole
(see panels page).
2
Assembly Instructions
7
Step 3
Fit the drawer bases
Slide a drawer base
down the grooves in the
drawer sides and
and down into the
groove in the drawer
front and .
Step 4
Fit the drawer backs
Fit a drawer back
between the drawer
sides and .
Make sure that the
drawer base fits into
the groove in the drawer
back .
Hold the drawer back
in position and tap the
knock-in pegs
through the holes in the
drawer sides and .
6
43
1 2
5
3 4
6
5
5
C
3 4
x 4
x 4
x 4
Step 5
Fit the handles
Attach a handle to
each of the 4 drawer
fronts and using
screws .
T
D
1 2
4
3
6
4
6
C
C
3
C
C
5
1 2
D
T
1 2
Important: You will need
3 more of these screws
from the drawer fittings
bag to fit the handles to
the doors at a later step.
8
Step 6
Assembly Instructions
x 4
Fit the drawer braces
Turn the 4 drawer
assemblies over and
hook a drawer brace
onto the bottom edge of
the drawer back .
Fix it to the drawer front
and drawer back using 2
screws .
V
E
V
E
V
E
E
E
V
x 4
W d
Fit runners to the
drawers
Fit the DL runner to
the bottom edge of the
left drawer side , as
shown, making sure that
it is pushed up against
the back of the drawer
front and . Use a
bradawl to mark the
fixing positions, then
secure with 2 screws .
Fit the DR runner to
the bottom edge of the
right drawer side
using the same method.
4
W c
3
1 2
F
W d
DR
Step 7
4
3
21
DL
F
F
F
F
W c
DL
5
5
Runners must be
pushed up against
the drawer front
hps://www.youtube.com/watch?v=Z6lGMy19h7Q
Fixing Bottom Mounter Runners
Important: Make sure
that the drawer assembly
is square before fitting
the drawer brace.
A
N
N
N
A
9
Step 8
Assembly Instructions
Prepare the divider
Fit a rail holder to the
divider using 2
screws .
Insert 2 large locking
cam nuts into the
divider .
Push 2 of the quickfit
dowels as far as they
will go into the divider .
Tap 6 wooden dowels
into the divider .
Note: Wooden dowels
must not stick out from
the edge by more than
10mm or they may
damage other panels.
10mm
N
A
B
A
N
N
N
A
B
B
N
N
N
Finished
front edge
G
G
L
B
13
13
A
N
13
L
G
13
Finished
front edge
B
B
A
N
N
A
N
B
B
Step 9
Prepare the horizontal
Insert 4 large locking
cam nuts into the
horizontal .
Push 4 of the quickfit
dowels as far as they
will go into the horizontal
. .
Tap 6 wooden dowels
into the horizontal .
A
8
8
8
B
N
8
13
Use the Main Fittings Bag for Steps 8 - end
Finished
front edge
A
N
N
N
A
Finished
front edge
Finished
front edge
10
Step 10
Assembly Instructions
I
I
Fit the base
Push the horizontal
onto the divider and
fit it using 2 screws .
Note: To make the
assembly easier, place
polystyrene blocks from
the packaging underneath
the panels to raise the
assembly.
8
13
I
8
13
Step 11
Prepare the wide
shelf
Insert 4 large locking
cam nuts into the
wide shelf .
Push 4 of the quickfit
dowels as far as they
will go into the wide shelf
. .
Tap 6 wooden dowels
into the wide shelf .
Step 12
A
9
9
9
B
N
B
B
B
B
A
N
N
A
N
Finished
front edge
9
13
Fit the wide shelf
Push the wide shelf onto
the divider .
Turn the 2 large locking
cam nuts fited to the
wide shelf clockwise
as far as they will go to
secure the panels.
Important: Make
sure there is no gap
between the fitted
panels.
9
13
B
9
9
B
Polystyrene
block
Polystyrene
block
hps://www.youtube.com/watch?v=9C7tgv5xnbE
Carcase Assembly
Finished
front edge
Finished
front edge
Finished
front edge
11
Step 13
Assembly Instructions
Prepare the drawer
divider
a: Fit 2 CL runners
to the drawer divider .
The 1st screw uses
the 1st hole in from the
front of the runner.
The 2nd and 3rd screws
. use the holes that line
up with the other panel
holes.
b: Fit a screw into
the hole at the top of the
runner .
c: Insert 2 large locking
cam nuts into the
drawer divider .
Push 2 of the quickfit
dowels as far as they
will go into the drawer
divider .
Tap 3 wooden dowels
into the drawer divider .
Turn the drawer
divider over
d: Fit 2 CR runners
to the drawer divider .
The 1st screw uses
the 1st hole in from the
front of the runner.
The 2nd and 3rd screws
. use the holes that line
up with the other panel
holes.
e: Fit a screw into
the hole at the top of the
runner .
W a
14
H
H
F
B
14
14
W a
W b
14
H
H
F
W b
a:
c:
b:
d: e:
A
N
14
W a
H
1st
screw
Finished
front edge
CL
Finished
front edge
F
W a
hps://www.youtube.com/watch?v=Z6lGMy19h7Q
Fixing Bottom Mounter Runners
CL
H
W a
H
H
CL
H
W a
H
H
CL
F
CL
F
CL
CL
A
N
N
N
A
B
B
W b
H
1st
screw
Finished
front edge
CR
CR
H
W b
H
H
Finished
front edge
F
CR
F
CR
F
CR
H
W b
H
H
Finished
front edge
Finished
front edge
Turn the drawer divider over
14
14
14 14
14
Finished
front edge
O
O
12
Step 14
Assembly Instructions
Fit the drawer divider
Push the drawer divider
. onto the horizontal .
Turn the 2 large locking
cam nuts fitted to the
drawer divider
clockwise as far as they
will go to secure the
panels.
Important: Make
sure there is no gap
between the fitted
panels.
Step 16
Finished
front edge
8
14
14 8
B
9
16
13
Fit the large top rail
Push the large top rail
up against the divider .
Tap 2 large wooden
dowels through the
divider and into the
large top rail until
they ‘’bottom out’’.
Step 15
Prepare the large top
rail
Tap 2 wooden dowels
into the large top rail .
O
16
13
16
13
Finished
front edge
16
N
N
N
16
13
Step 17
Assembly Instructions
Prepare the small top
rail
Tap 2 wooden dowels
into the small top rail .
N
17
N
N
Finished
front edge
17
Step 18
W b
G
1st
screw
Finished
front edge
CR
Finished
front edge
F
CR
F
CR
F
CR
H
W b
H
H
CR
H
W b
H
H
A
N
N
N
A
B
B
Prepare the right side
a: Fit 2 CR runners
to the right side .
The 1st screw uses
the 1st hole in from the
front of the runner.
The 2nd and 3rd screws
. use the holes that line
up with the other panel
holes.
b: Fit a screw into
the hole at the top of the
runner .
Insert 2 large locking
cam nuts into the
right side .
Push 2 of the quickfit
dowels as far as they
will go into the right side
.
Tap 3 wooden dowels
into the right side .
W b
12
H
H
F
B
12
12
W b
A
N
12
12
12
Finished
front edge
Finished
front edge
N
A
Finished
front edge
14
Step 19
Assembly Instructions
Step 20
12
CR
CR
Fit the small top rail
to the right side
Push the small top rail
down onto the right side
. .
17
12
17
Finished
front edge
Finished
front edge
Fit the right side
Push the right side
onto the horizontal .
Make sure that the small
top rail is pushed
onto the 2 large wooden
dowels fitted through
the divider .
Turn the 2 large locking
cam nuts fitted to the
horizontal clockwise
as far as they will go to
secure the panels.
Important: Make
sure there is no gap
between the fitted
panels.
Step 21
12
8
B
O
8
17
13
12
8
17
13
Prepare the back
cross rail
Insert 2 large locking
cam nuts into the
back cross rail .
Push 2 of the quickfit
dowels as far as they
will go into the back
cross rail .
Tap 2 wooden dowels
into the back cross rail .
A
19
19
9
B
N
B
B
N
A
19
Finished
front edge
15
Step 22
Assembly Instructions
Prepare the front
cross rail
Tap 4 wooden dowels
into the front cross rail .
Step 23
Step 24
I
Fit the back cross rail
Push the back cross rail
. onto the right side .
Turn the large locking
cam nut fitted to the
back cross rail
clockwise as far as it will
go to secure the panels.
Important:
Make sure there
is no gap between
the fitted panels.
Secure the cross back
rail to the drawer
divider using screw .
19 12
B
19
19
14
I
19
14
12
N
N
N
N
Finished
front edge
N
18
18
14
12
I
18
Fit the front cross rail
Push the front cross rail
. onto the right side .
Secure the front cross
rail to the drawer
divider using screw .
18 12
18
14
I
N
A
A
N
16
Step 25
Assembly Instructions
Step 26
B
B
A
N
Prepare the plinth
Insert 2 large locking
cam nuts into the
plinth .
Push 2 of the quickfit
dowels as far as they
will go into the plinth .
Tap 2 wooden dowels
into the plinth .
A
15
15
15
B
N
15
12
Fit the plinth
Push the plinth onto
the right side .
Turn the large locking
cam nut fitted to the
plinth clockwise as
far as it will go to secure
the panels.
Important: Make sure
there is no gap between
the fitted panels.
Step 27
15
12
B
15
Prepare the back rail
Insert 2 large locking
cam nuts into the
back rail .
Push 2 of the quickfit
dowels as far as they
will go into the back rail
. .
Tap 2 wooden dowels
into the back rail .
A
20
20
20
B
N
B
B
N
A
Finished
front edge
20
15
Finished
front edge
Finished
front edge
Finished
front edge
17
Step 28
Assembly Instructions
Prepare the left side
a: Fit 2 CL runners
to the left side .
The 1st screw uses
the 1st hole in from the
front of the runner.
The 2nd and 3rd screws
. use the holes that line
up with the other panel
holes.
b: Fit a screw into
the hole at the top of the
runner .
c: Insert 2 large locking
cam nuts into the left
side .
Push 2 of the quickfit
dowels as far as they
will go into the left side
. ..
Tap 3 wooden dowels
into the left side .
Fit a rail holder to the
left side using 2
screws .
W a
11
H
H
F
B
11
11
W a
a:
b:
A
N
11
W a
H
1st
screw
Finished
front edge
CL
Finished
front edge
F
W a
CL
H
W a
H
H
CL
H
W a
H
H
CL
F
CL
F
c:
CL
CL
A
N
N
N
A
B
B
G
G
L
L
G
11
11
11
11
Finished
front edge
18
Step 29
Assembly Instructions
Step 30
20
13
Fit the back rail
Push the back rail
onto the divider .
Turn the large locking
cam nut fitted to the
back rail clockwise
as far as it will go to
secure the panels.
Important: Make sure
there is no gap between
the fitted panels.
20
13
B
20
Fit the left side
Push the left side
onto the assembly.
Turn the 7 large locking
cam nuts clockwise
as far as it will go to
secure the panels.
Important: Make sure
there is no gap between
the fitted panels.
11
B
Note: Support the
back rail until the left
side has been fitted
in the next step.
11
19
Step 31
Assembly Instructions
Fit the top
Push the top onto
the assembly.
Turn the 6 large locking
cam nuts clockwise
as far as it will go to
secure the panels.
Important: Make sure
there is no gap between
the fitted panels.
7
B
7
Fit the 6 plastic nails
Tap 2 plastic nails
into the bottom edge of
each side and as
shown.
Tap 2 plastic nails
into the plinth as
shown.
K
11 12
K
K
K
15
K
K
K
K
Step 32
11
12
15
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28

Argos Adult Malibu 558/2255 Assembly Instructions Manual

Brand
Argos
Model
Adult Malibu 558/2255
Type
Assembly Instructions Manual
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents