B&Q CSS1350 Assembly Manual

B&Q
Brand
B&Q
Model
CSS1350
Type
Assembly Manual
Before you Start …
Build the unit close to where it will be used. Handle all items carefully. Always lay panels down on a flat
smooth surface. Complete each stage before moving onto the next one.
Follow these guidelines and take your time.
Please ignore this guide if you have purchased a Corner Wardrobe Conversion Kit.
If any parts are missing, please call the Helpline on 01769 575500 and our team will get things sorted.
Important - If you have purchased a Stable Wardrobe Conversion Pack, please refer to the instructions
within that pack, for fitting of the stable conversion and exact positioning of the stable wardrobe.
Cross Head Screwdriver
Drill
Level
2.5mm
Drill Bit
5mm
Drill Bit
1 x RH Side Panel
1 x LH Side Panel
1 x Top Panel
1 x Base Panel (single sided)
1 x Shelf
1 x Back Rail
1 x Back Panel
1 x Plinth
1
2
3
4
5
6
Panels Hardware
ASSEMBLY GUIDE
Minimum Tools Required
Hammer
WARDROBE
DOUBLE
3 x
A
20 x
C
2 x
B
12 x
E
4 x
F
7
Fitted
Bedroom
Range
1
2
3
4
5
6
12 x
G
4 x
H
8 x
I
8 x
J
Flat Head Screwdriver
Please use scissors to open the
bag of fittings and then empty
the contents into a bowl, so
that they do not get lost!
8 x
K
3 x
L
4 x
N
2 x
M
12 x
O
4 x
P
6 x
Q
1 x
R
Handles, Handle screws & Doors are to be supplied
independently and not covered by this guide.
4 x
D
8
8
PLEASE keep all fittings away from young children
Bradawl
Scissors
Tape Measure
7
5 x
8 x
S
Screws are for fitting a
Traditional Cornice to your
Robe. If you are not fitting
a Traditional Cornice, you
will have these spare.
T
T
4 x
AT
Slide the Back Panel , coloured-side facing down, along the grooves in the
Side Panels and underneath the Back Rail.
Plain Chipboard Surface
F551
Tight
against
panel
F139
Tight
against
panel
1
3
Fit panels , , &
to panel .
2
3 4
6
8
1
Carefully fit parts , , and to side panel , as shown. Now repeat this process for side panel2 .
The Shelf can be fitted in a number of positions. Screw in the two short Cam legs at the desired height. In
these instructions we will show the Shelf fitted in this upper position.
C
Use two people to fit panel to panels , , & .
Insert the Cams as above, but with the arrows pointing towards panel , and tighten clockwise.
3 4
6
8
2
NOTE: Fixing block should be fitted
to panel , as shown, before panel is
fitted to panel .
IMPORTANT: To assemble this unit you will need a ceiling height of at least 2200mm
F551
Tight
against
panel
F139
Tight
against
panel
GHG
D
I
I
H
N
H
G
G H I N
1
1
2
8
8 8
R
R
1
1
3
4
6
8
2
8
4
R
Then fit Cams as
shown, ensuring that
the arrow is pointing
towards panel , and
tighten clockwise.
O
1
2
Panel protectors should be fitted, prior
to standing the unit up. Fit 2 x to the
bottom of each side panel, as shown,
approx. 50mm in from front and back.
Locate the centre of the Top and Base
Panel, and align the crease in the Back
Panel with these points. Then secure the
Back into place using Nails , along the
back edge of the Top and Base.
Before the Back Panel is nailed, check
the Unit is square by measuring AA and
BB. These must be equal.
A:A = B:B
Using 2 people
stand the Unit up
A
A
B
B
F
F
F
F
6
E
E
E
E
E
E
E
E
E
E
E
E
7
7
7
F
F
GH
GG
G
Have you bought a Combi Pack? - If you are fitting a Combi Pack to this unit, you will have
to carefully drill through the two holes, in the underside of the base panel, using a 5mm drill bit, before
you stand the unit up.
CSS1350 05/10
Swivel the Bracket back and fix the Bracket to the wall,
then tighten .
Take care when drilling the wall that you do not drill
into any pipes, wires, etc. If in doubt, consult an expert.
!!
HAVE YOU BOUGHT
A COMBI PACK
OR LINEN PRESS?
You are now finished with
these instructions.
DO NOT complete steps
14 to 19.
Please now refer to the
instructions packed
with the Combi Pack
or Linen Press.
!!
HAVE YOU BOUGHT
A DOUBLE INTERIOR
STORAGE CHEST
OR CUBE
STORAGE?
Please now refer to the
instructions packed with
the Interior Storage Chest or
Cube Storage.
When instructed to do so you
will need to come back and
complete stages 14 to 19.
Fitting of Shelf
4
!!
HAVE YOU BOUGHT
A COMBI PACK
OR LINEN PRESS?
You are now finished with
these instructions.
DO NOT complete steps
14 to 19.
Please now refer to the
instructions packed
with the Combi Pack
or Linen Press.
!!
HAVE YOU BOUGHT
A DOUBLE INTERIOR
STORAGE CHEST
OR CUBE
STORAGE?
Please now refer to the
instructions packed with
the Interior Storage Chest or
Cube Storage.
When instructed to do so you
will need to come back and
complete stages 14 to 19.
!!
HAVE YOU BOUGHT
A COMBI PACK
OR LINEN PRESS?
You are now finished with
these instructions.
DO NOT complete steps
14 to 19.
Please now refer to the
instructions packed
with the Combi Pack
or Linen Press.
!!
HAVE YOU BOUGHT
A DOUBLE INTERIOR
STORAGE CHEST
OR CUBE
STORAGE?
Please now refer to the
instructions packed with
the Interior Storage Chest or
Cube Storage.
When instructed to do so you
will need to come back and
complete stages 14 to 19.
P
P
P
P
P
5
Lower the shelf on to the protruding Cam legs in the Wardrobe
side. Gently ‘push’ down until the panel ‘clicks’ into place.
5
Now fit
hanging
rail
Have you bought a Single Interior Storage Chest or Cube Storage?
Please now refer to the assembly guide packed with the Interior Storage Chest or Cube Storage.
When instructed to do so you will need to come back and complete stages 5-11.
Have you bought a Combi Pack Or Linen Press?
You are now finished with this guide. DO NOT complete steps 5-11.
Please now refer to the assembly guide packed with the Combi Pack or Linen Press.
Important Information
!
5
Fitting of Hinge Plates
Starting from the bottom,
count holes carefully
before fitting the Hinges.
hole number
2 and 3
hole number
17 and 18
hole number
35 and 36
hole number
52 and 53
Arrow must point towards front edge
J
Arrow must point towards
front edge
1
J J J J
Joining Units
6
Securing to Wall
7
To prevent possible overbalancing we
recommend that this Unit is secured to a
suitable wall by use of bracket fitted to
the top of the Unit.
M
B
M
Fix the Bracket loosely onto the top of the Unit
using Screw and mark the wall for the wall
fixing. Swivel the Bracket away from the wall and
drill a hole in the wall using a suitable drill bit and
fit your wall fixing.
M
B
B
Starting in a corner make sure the first
Unit is level. Push the next Unit up against
the first Unit and level.
Join together using the connector bolts:
If you have purchased a Trim Pack you will need to
fit it now. Please refer to the Trim Pack Assembly
Guide before continuing with this assembly.
Check that ends are flush and in line then clamp
together. Drill through three of the 5 mm holes down
the centre of the side panel into the adjoining panel of
the other Robe.
Push Connector into the hole and then screw Bolt in
from the other side - tighten with a screwdriver.
L
L
A
B&Q plc, Chandlers Ford, Hampshire, SO53 3YX.
Visit us at www.diy.com
Recycling – the packaging materials for this product may be recycled through your local recycling centre. When you want to dispose of
the product itself, please consider donating it to a local charitable organisation. Otherwise, recycle it through your local recycling centre.
9
Fitting of Plinth
The plinth should be
cut to the required
length, allowing for
the mitre joint, and
then stuck onto the
unit, using a suitable
adhesive.
10
Fitting of Cornice
The cornice should be cut to the
required length, allowing for the
mitre and the overhang, and then
screwed into place using suitable
fixings (not supplied).
If space allows, screw into place
from above, through the 15mm
flat. If not, using a 5mm drill
bit, drill and countersink from
the underside of the top panel,
and fix in place. (And then fill
afterwards, if required).
Note: Plinths and Cornices are supplied separately. If you
are in any doubt about fitting these items, you should
seek advice from an expert.
Door Hinges
8
Handle Fixing
From the rear face of the Door, drill
through the holes using a 2.5mm
diameter drill.
From the front face of the Door,
open out the 2.5mm diameter holes
using a 5mm drill.
Screw Handles to Doors with the
Screws provided.
Insert the Hinges into the large
holes in the Doors and secure into
place using Screws .
Stick the Door Buffers onto
the bottom corners of the Doors
opposite to the Hinges.
Before fitting the Hinges to your Door you will have to drill the hole(s) required
through the appropriate pilot holes for the Handles you have purchased.
PILOT
HOLES
Q
Q
Q
S
S
S
S
C
Q
Ensure your unit is level before you attempt to fit your Doors.
Fit the Hinge Covers
over the Hinges.
K
Push hook on the Hinge Arm underneath the Hinge Plate.
Press front of Hinge Arm down onto Hinge Plate until it
‘clicks’ into place.
Before adjusting the Doors, use a spirit level to
check the Base (or Top) of the unit is level front-to-
back and side-to-side in the three positions shown.
Height: Loosen screws ‘A’ on fixing
plates and move Door up or down as
required. Retighten screws ‘A’.
A
A
B
C
CLICK!
A
A
B
C
CLICK!
Make the unit level BEFORE making any adjustment to
the hinges as shown.
Forward or Backwards:
Loosen
screw ‘B’ on fixing plate and move
Door in or out as required. Retighten
screw ‘B’.
Sideways: To move Door ‘OUT’ at
hinge position, slacken screw ‘C’.
To move Door ‘IN’ at hinge position,
tighten screw ‘C’.
A
A
B
C
CLICK!
A
A
B
C
CLICK!
A
A
B
C
CLICK!
K
S
That’s the Double Wardrobe completed. Take care of your unit by using a damp cloth to clean it.
Soft Closer
11
The soft close mechanism , should be fitted onto one of the hinges, two per door, as shown,
(the mechanism simply clips into place over and into the hinge cup).
Adjustment of this device can then be made, by turning the dial at the bottom of the unit.
AT
AT
S
CSS1350 05/10
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

B&Q CSS1350 Assembly Manual

B&Q
Brand
B&Q
Model
CSS1350
Type
Assembly Manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents