4 x
Cross Head Screwdriver
Drill
Level
3mm
Drill Bit
5mm
Drill Bit
1 x Side
1 x Side
1 x Base
2 x Rail
2 x Support Shelf Rail
1 x Oven Support Shelf
2 x Oven Spacer Panel
1
2
3
4
5
22 x
C
15mm
Panels Hardware
ASSEMBLY GUIDE
Minimum Tools required
Hammer
2 x
D
BASE
Cabinet
Built Under Oven Housing
1
2
3
4
5
4 x
A
2 x
E
2 x
K
25mm
H
50 mm
6
6 x
DD
30 mm
4
5
6
Before you Start …
WARNING: Installation should be performed by a competent person only. This product could
be dangerous if incorrectly installed. All assembly fittings except legs and shelf pegs have
been pre-inserted. If any are missing or there is a problem with the panels, please call the
Helpline on 01769 575500 and our team will get things sorted.
Cleaning – Use mild soap and water only. Do not use abrasive cleaners.
Legs
4 x
S
2 x
U
4 x
T
2 x
V
Please use scissors to open the
bag of fittings and then empty
the contents into a bowl, so
that they do not get lost!
7
7
To protect your kitchen doors from any
excess heat emitted by your oven, it is
strongly recommended that an appropriate
Oven Heat Deflector Kit is fitted around
the oven aperture in this unit. Suitable kits
are available from B&Q and details can be
found in the kitchen price list.
Fit panels & to panel
Fit panel to panels &
3 4 1
Tighten metal cams
3 4
2
Screw panel to panel using 3 x screws as shown.
Repeat this procedure for panel
3
4
4
1
1
3
4
4
2
2
5 1
DD
1
3
5
DD
DD
DD
1
2
Secure panel to 2 x panel with 4 x screws.
Now fit oven spacer panels , if required, on top of
panel to raise the oven if it is sitting too low in the unit.
1
3
4
4
6
5
H
H
H
6 5
2
Fit oven filler panel chosen.
Position to the face of the cabinet
at the bottom.
Ensure panel is level and that
clearance is allowed for oven door
above.
Fix using 2 x brackets and
2 x screws to the inside of the
cabinet.
A
C
2 x
Then affix the
filler panel from
the inside using
2 x screws.
C
A
2 x
C
3
4
Now affix your cabinet legs
To fit legs, turn unit upside down
Fitting of Legs
Care should be taken when fitting legs and fitting to wall as Unit will be heavy
Cabinet
Underside
Position as shown,
lip on underside of side
panel .
Ensure screwhole is not
over panel join.
1
Drill pilot holes
3mm x 3 positions
3mm
Secure with screw
x 3 positions
Push
adjustable leg, into
leg boss
S
C
S
T
5
Rotate to adjust
height
6
7
CSS1108 09/09
Notes:
Lay plinth panel in front of cabinet legs. Position plinth clip plate opposite front
cabinet legs. Secure with 2 x screws .
Slide into . Stand plinth up.
C
U
V
T
U
U
To fit plinths
7
All legs are pre-set at 150mm height.
Rotate to adjust up and down, to level the unit.
Drill a 5mm hole through both side panels.
Join together using joining bolts .
To Fit to wall, drill 3mm pilot hole into side panel of cabinet.
Fix 2 x bracket using 2 x screws
Levelling, Joining & Fitting to Wall
A
C
D
Wall Fitting not supplied Use appropriate fittings to secure cabinet
to wall (depending on wall type).
6
/
