Savant ENC-R2LID-00 Reference guide

Savant
Brand
Savant
Model
ENC-R2LID-00
Type
Reference guide

This manual is also suitable for

The Savant SmartLighting Recess Mount Enclosure Lid, ENC-4LID for the four-module
enclosure and ENC-R2LID for the two-module enclosure Quick Reference Guide provides
installation information for both models.
Box Contents
(1) Recess Mount Enclosure Lid for 4-modules (ENC-R4LID-xx)
(1) Recess Mount Trim for 4 modules (071-2580-091)
(1) Recess Mount Hardware Kit for 4 modules (075-8090-025)
•
(1) Enclosure Door Latch (015-2580-120)
•
(2) Enclosure Hinge (015-2580-122)
•
(2) Screw 6-32 x 0.375 in TRS HD MB (039-5150-600)
•
(3) Screw 6-32 x 3/8 PH-UFL-STL-Z (039-5150-619)
•
(4) Screw 10-32 x 3/8 PN-PN-INT-SEMS-MS-STL-Z (039-5150-934)
•
(4) Screw 10 x 1/2 PHL FHD Z (039-5150-960)
Or
(1) Recess Mount Enclosure Lid for 2-modules (ENC-R2LID-xx)
(1) Recess Mount Trim for 2 modules (071-2580-084)
(1) Recess Mount Hardware Kit for 2 modules (075-8090-025)
•
(1) Enclosure Door Latch (015-2580-120)
•
(2) Enclosure Hinge (015-2580-122)
•
(2) Screw 6-32 x 0.375 in TRS HD MB (039-5150-600)
•
(3) Screw 6-32 x 3/8 PH-UFL-STL-Z (039-5150-619)
•
(4) Screw 10-32 x 3/8 PN-PN-INT-SEMS-MS-STL-Z (039-5150-934)
•
(4) Screw 10 x 1/2 PHL FHD Z (039-5150-960)
(1) Quick Reference Guide (this document)
System Components
Four-module Enclosure Box (ENC-4000-xx)
Two-module Enclosure Box (ENC-2000-xx)
Specifications
Environmental
Environmental
Temperature
32° to 95° F (0° to 35° C) - Ambient Operating
Recess Mount Lid - Dimensions and Weight (ENC-R4LID)
Recess Mount Lid - Dimensions and Weight (ENC-R4LID)
Height
38.5 in/97.79 cm
Width
20.6 in/52.32 cm
Depth
0.128 in/0.325 cm
Weight
4.14 lb/1.87 kg
Recess Mount Lid - Dimensions and Weight (ENC-R2LID)
Recess Mount Lid - Dimensions and Weight (ENC-R2LID)
Height
21.5 in/54.61 cm
Width
20.6 in/52.32 cm
Depth
4.0 in/10.16 cm
Weight
2.58 lb/1.17 kg
SURFACE MOUNT ENCLOSURE
Install Hinge to Enclosure (See Figures 1, 3 & 4)
1. Attach Male Hinge (2580-120) to Hinge Bracket (2580-064) using two, 10-32 x 3/8 Pan Head Screws (5150-934).
2. Attach Hinge Brackets to Enclosure, in two places using two, 10-32 x 3/8 Pan Head Screws (5150-934).
Install Hinge to Enclosure Lid (See Figures 2 & 5)
3. Attach Female Hinge (2580-122) to Enclosure, in two places to Lid using two, 10-32 x 3/8 Pan Head Screws (5150-934).
Install Latch to Enclosure Lid (See Figures 2, 6 & 7)
4. Insert Latch (2580-120) through allocated cutout in Enclosure Lid; two small dimples on Latch should face outside.
5. Secure Enclosure Lid closed with two black screws (5150-600). Use two holes above and below Latch.
6900-790.01
Revised 05/08Technical Support 1-800-527-5527 www.LiteTouch.com
WARNING: Read instructions prior to installation or you may VOID THE WARRANTY!
Figure 4
Attach Bracket to Enclosure
Figure 3
Attach Hinge to Bracket
Note: Hinges are installed
into two locations on
both the Enclosure
and Enclosure Lid.
Figure 5
Attach Hinge to Lid
Figure 2
Hinge & Latch Install to Enclosure Lid
Figure 6
Attach Latch to Lid
Figure 7
Latch Fully Assembled & Attached to Lid
LITETOUCH ENCLOSURE LID INSTALLATION
Male Hinge
(2580-120)
Hinge Bracket
(2580-064)
Male Hinge
(2580-120)
Hinge Bracket
(2580-064)
Enclosure
Enclosure
Enclosure
Lid
Latch
Installation
Location
Female Hinge
(2580-122)
Hinge
Installation
Locations
Enclosure
Figure 1
Hinge Install to Enclosure
Hinge
Installation
Locations
Enclosure
Lid
Latch
Assembly
Screws
10-32 x 3/8
(5150-934)
Screws
10-32 x 3/8
(5150-934)
Latch (2580-120)
Enclosure
Lid
Latch
(2580-120)
Enclosure
Lid
Secure Lid
Locations
Recess Mount Enclosure Lid
Refer to Pre-Installation Instructions for SmartLighting Systems (009-0763-xx)
CAUTION: In accordance with CSA requirements, the interior space isolates line and low-voltage sections, and this isolation must be maintained. Place Savant enclosures in an environment in which
ambient temperatures are between 32°F and 95°F. Modules may create some noise and should not be located where this may be objectionable.
Installation Instructions
Enclosures can be installed before or after wiring.
NOTE: Hinges are installed into two locations on both the Enclosure Trim and Enclosure Lid.Enclosure Trim is installed in three locations.
1. Install Hinge and Trim to Enclosure (See Figures 1, 2 and 3)
a. Attach male hinge and hinge spacer to enclosure trim in two places using using two flat head screws.
b. Attach assembled enclosure trim to enclosure with two flat head screws.
2. Install Hinge to Enclosure Lid (See Figures 4 and 5)
a. Attach female hinge to lid on top of side edge using two pan head screws.
b. Attach female hinge to lid on bottom of side edge using two pan head screws.
3. Insert Latch to Enclosure Lid (See Figures 6 and 7)
a. Insert latch through allocated cutout in enclosure lid: two small dimples on latch should face outside.
b. Secure enclosure lid closed with two black screws. Use holes above and below latch.
SmartLighting Recess Mount
Enclosure Lid
(ENC-R4LID and ENC-R2LID)
Quick Reference Guide
009-0764-00
ENC-R4LID-00
ENC-R2LID-00
100912
1. Install Hinge to Enclosure
Figure 4
Figure 5
6900-791.00
Revised 05/08Technical Support 1-800-527-5527 www.LiteTouch.com
WARNING: Read instructions prior to installation or you may VOID THE WARRANTY!
Figure 4
Attach Enclosure Trim To Enclosure
Figure 3
Attach Hinge to Enclosure Trim
Note: Hinges are installed
in two locations on
both the Enclosure
Trim and Lid.
Enclosure Trim is
installed in three
locations
Figure 5
Attach Hinge to Lid
Figure 2
Hinge & Latch Install to Enclosure Lid
Figure 6
Attach Latch to Lid
Figure 7
Latch Fully Assembled & Attached to Lid
LITETOUCH ENCLOSURE LID INSTALLATION
Male Hinge
(2580-120)
Male Hinge
(2580-120)
Hinge Spacer
(2580-072)
Enclosure Trim
(2580-070)
Enclosure
Enclosure
Lid
Latch
Installation
Location
Female Hinge
(2580-122)
Hinge
Installation
Locations
Enclosure
Figure 1
Hinge Install to Enclosure
Hinge
Installation
Locations
Enclosure
Lid
Latch
Assembly
Screws
10-32 x 1/2
(5150-960)
Screws
10-32 x 38
(5150-934)
Latch (2580-120)
Enclosure
Lid
Latch
(2580-120)
Enclosure
Lid
RECESS MOUNT ENCLOSURE
Install Hinge and Trim to Enclosure (See Figures 1, 3 & 4)
1. Attach Male Hinge (2580-120) and Hinge Spacer (2580-072) to Enclosure Trim, in two places, using two, 10-32 x 1/2 Flat Head
Screws (5150-960).
2. Attach assembled Enclosure Trim to Enclosure with 6-32 x3/8 Flat Head Screws (5150-619).
Install Hinge to Enclosure Lid (See Figures 2 & 5)
3. Attach Female Hinge (2580-122) to Enclosure Lid using two, 10-32 x 3/8 Pan Head Screws (5150-934).
Install Latch to Enclosure Lid (See Figures 2, 6 & 7)
4. Insert Latch (2580-120) through allocated cutout in Enclosure Lid; two small dimples on Latch should face outside.
5. Secure Enclosure Lid closed with two black screws (5150-600). Use two holes above and below Latch.
Enclosure
Trim
(2580-070)
Secure Lid
Locations
Screws
6-32 x 3/8
(5150-619)
Figure 2
6900-791.00
Revised 05/08Technical Support 1-800-527-5527 www.LiteTouch.com
WARNING: Read instructions prior to installation or you may VOID THE WARRANTY!
Figure 4
Attach Enclosure Trim To Enclosure
Figure 3
Attach Hinge to Enclosure Trim
Note: Hinges are installed
in two locations on
both the Enclosure
Trim and Lid.
Enclosure Trim is
installed in three
locations
Figure 5
Attach Hinge to Lid
Figure 2
Hinge & Latch Install to Enclosure Lid
Figure 6
Attach Latch to Lid
Figure 7
Latch Fully Assembled & Attached to Lid
LITETOUCH ENCLOSURE LID INSTALLATION
Male Hinge
(2580-120)
Male Hinge
(2580-120)
Hinge Spacer
(2580-072)
Enclosure Trim
(2580-070)
Enclosure
Enclosure
Lid
Latch
Installation
Location
Female Hinge
(2580-122)
Hinge
Installation
Locations
Enclosure
Figure 1
Hinge Install to Enclosure
Hinge
Installation
Locations
Enclosure
Lid
Latch
Assembly
Screws
10-32 x 1/2
(5150-960)
Screws
10-32 x 38
(5150-934)
Latch (2580-120)
Enclosure
Lid
Latch
(2580-120)
Enclosure
Lid
RECESS MOUNT ENCLOSURE
Install Hinge and Trim to Enclosure (See Figures 1, 3 & 4)
1. Attach Male Hinge (2580-120) and Hinge Spacer (2580-072) to Enclosure Trim, in two places, using two, 10-32 x 1/2 Flat Head
Screws (5150-960).
2. Attach assembled Enclosure Trim to Enclosure with 6-32 x3/8 Flat Head Screws (5150-619).
Install Hinge to Enclosure Lid (See Figures 2 & 5)
3. Attach Female Hinge (2580-122) to Enclosure Lid using two, 10-32 x 3/8 Pan Head Screws (5150-934).
Install Latch to Enclosure Lid (See Figures 2, 6 & 7)
4. Insert Latch (2580-120) through allocated cutout in Enclosure Lid; two small dimples on Latch should face outside.
5. Secure Enclosure Lid closed with two black screws (5150-600). Use two holes above and below Latch.
Enclosure
Trim
(2580-070)
Secure Lid
Locations
Screws
6-32 x 3/8
(5150-619)
Figure 3
6900-791.00
Revised 05/08Technical Support 1-800-527-5527 www.LiteTouch.com
WARNING: Read instructions prior to installation or you may VOID THE WARRANTY!
Figure 4
Attach Enclosure Trim To Enclosure
Figure 3
Attach Hinge to Enclosure Trim
Note: Hinges are installed
in two locations on
both the Enclosure
Trim and Lid.
Enclosure Trim is
installed in three
locations
Figure 5
Attach Hinge to Lid
Figure 2
Hinge & Latch Install to Enclosure Lid
Figure 6
Attach Latch to Lid
Figure 7
Latch Fully Assembled & Attached to Lid
LITETOUCH ENCLOSURE LID INSTALLATION
Male Hinge
(2580-120)
Male Hinge
(2580-120)
Hinge Spacer
(2580-072)
Enclosure Trim
(2580-070)
Enclosure
Enclosure
Lid
Latch
Installation
Location
Female Hinge
(2580-122)
Hinge
Installation
Locations
Enclosure
Figure 1
Hinge Install to Enclosure
Hinge
Installation
Locations
Enclosure
Lid
Latch
Assembly
Screws
10-32 x 1/2
(5150-960)
Screws
10-32 x 38
(5150-934)
Latch (2580-120)
Enclosure
Lid
Latch
(2580-120)
Enclosure
Lid
RECESS MOUNT ENCLOSURE
Install Hinge and Trim to Enclosure (See Figures 1, 3 & 4)
1. Attach Male Hinge (2580-120) and Hinge Spacer (2580-072) to Enclosure Trim, in two places, using two, 10-32 x 1/2 Flat Head
Screws (5150-960).
2. Attach assembled Enclosure Trim to Enclosure with 6-32 x3/8 Flat Head Screws (5150-619).
Install Hinge to Enclosure Lid (See Figures 2 & 5)
3. Attach Female Hinge (2580-122) to Enclosure Lid using two, 10-32 x 3/8 Pan Head Screws (5150-934).
Install Latch to Enclosure Lid (See Figures 2, 6 & 7)
4. Insert Latch (2580-120) through allocated cutout in Enclosure Lid; two small dimples on Latch should face outside.
5. Secure Enclosure Lid closed with two black screws (5150-600). Use two holes above and below Latch.
Enclosure
Trim
(2580-070)
Secure Lid
Locations
Screws
6-32 x 3/8
(5150-619)
Figure 1
2. Install Hinge to Enclosure Lid
SURFACE MOUNT ENCLOSURE
Install Hinge to Enclosure (See Figures 1, 3 & 4)
1. Attach Male Hinge (2580-120) to Hinge Bracket (2580-064) using two, 10-32 x 3/8 Pan Head Screws (5150-934).
2. Attach Hinge Brackets to Enclosure, in two places using two, 10-32 x 3/8 Pan Head Screws (5150-934).
Install Hinge to Enclosure Lid (See Figures 2 & 5)
3. Attach Female Hinge (2580-122) to Enclosure, in two places to Lid using two, 10-32 x 3/8 Pan Head Screws (5150-934).
Install Latch to Enclosure Lid (See Figures 2, 6 & 7)
4. Insert Latch (2580-120) through allocated cutout in Enclosure Lid; two small dimples on Latch should face outside.
5. Secure Enclosure Lid closed with two black screws (5150-600). Use two holes above and below Latch.
6900-790.01
Revised 05/08Technical Support 1-800-527-5527 www.LiteTouch.com
WARNING: Read instructions prior to installation or you may VOID THE WARRANTY!
Figure 4
Attach Bracket to Enclosure
Figure 3
Attach Hinge to Bracket
Note: Hinges are installed
into two locations on
both the Enclosure
and Enclosure Lid.
Figure 5
Attach Hinge to Lid
Figure 2
Hinge & Latch Install to Enclosure Lid
Figure 6
Attach Latch to Lid
Figure 7
Latch Fully Assembled & Attached to Lid
LITETOUCH ENCLOSURE LID INSTALLATION
Male Hinge
(2580-120)
Hinge Bracket
(2580-064)
Male Hinge
(2580-120)
Hinge Bracket
(2580-064)
Enclosure
Enclosure
Enclosure
Lid
Latch
Installation
Location
Female Hinge
(2580-122)
Hinge
Installation
Locations
Enclosure
Figure 1
Hinge Install to Enclosure
Hinge
Installation
Locations
Enclosure
Lid
Latch
Assembly
Screws
10-32 x 3/8
(5150-934)
Screws
10-32 x 3/8
(5150-934)
Latch (2580-120)
Enclosure
Lid
Latch
(2580-120)
Enclosure
Lid
Secure Lid
Locations
Figure 4
SURFACE MOUNT ENCLOSURE
Install Hinge to Enclosure (See Figures 1, 3 & 4)
1. Attach Male Hinge (2580-120) to Hinge Bracket (2580-064) using two, 10-32 x 3/8 Pan Head Screws (5150-934).
2. Attach Hinge Brackets to Enclosure, in two places using two, 10-32 x 3/8 Pan Head Screws (5150-934).
Install Hinge to Enclosure Lid (See Figures 2 & 5)
3. Attach Female Hinge (2580-122) to Enclosure, in two places to Lid using two, 10-32 x 3/8 Pan Head Screws (5150-934).
Install Latch to Enclosure Lid (See Figures 2, 6 & 7)
4. Insert Latch (2580-120) through allocated cutout in Enclosure Lid; two small dimples on Latch should face outside.
5. Secure Enclosure Lid closed with two black screws (5150-600). Use two holes above and below Latch.
6900-790.01
Revised 05/08Technical Support 1-800-527-5527 www.LiteTouch.com
WARNING: Read instructions prior to installation or you may VOID THE WARRANTY!
Figure 4
Attach Bracket to Enclosure
Figure 3
Attach Hinge to Bracket
Note: Hinges are installed
into two locations on
both the Enclosure
and Enclosure Lid.
Figure 5
Attach Hinge to Lid
Figure 2
Hinge & Latch Install to Enclosure Lid
Figure 6
Attach Latch to Lid
Figure 7
Latch Fully Assembled & Attached to Lid
LITETOUCH ENCLOSURE LID INSTALLATION
Male Hinge
(2580-120)
Hinge Bracket
(2580-064)
Male Hinge
(2580-120)
Hinge Bracket
(2580-064)
Enclosure
Enclosure
Enclosure
Lid
Latch
Installation
Location
Female Hinge
(2580-122)
Hinge
Installation
Locations
Enclosure
Figure 1
Hinge Install to Enclosure
Hinge
Installation
Locations
Enclosure
Lid
Latch
Assembly
Screws
10-32 x 3/8
(5150-934)
Screws
10-32 x 3/8
(5150-934)
Latch (2580-120)
Enclosure
Lid
Latch
(2580-120)
Enclosure
Lid
Secure Lid
Locations
Figure 5
Figure 2
Figure 3
Figure 1
3. Install Latch to Enclosure Lid
Figure 1
Figure 2
Figure 3
Figure 4
Figure 5
SURFACE MOUNT ENCLOSURE
Install Hinge to Enclosure (See Figures 1, 3 & 4)
1. Attach Male Hinge (2580-120) to Hinge Bracket (2580-064) using two, 10-32 x 3/8 Pan Head Screws (5150-934).
2. Attach Hinge Brackets to Enclosure, in two places using two, 10-32 x 3/8 Pan Head Screws (5150-934).
Install Hinge to Enclosure Lid (See Figures 2 & 5)
3. Attach Female Hinge (2580-122) to Enclosure, in two places to Lid using two, 10-32 x 3/8 Pan Head Screws (5150-934).
Install Latch to Enclosure Lid (See Figures 2, 6 & 7)
4. Insert Latch (2580-120) through allocated cutout in Enclosure Lid; two small dimples on Latch should face outside.
5. Secure Enclosure Lid closed with two black screws (5150-600). Use two holes above and below Latch.
6900-790.01
Revised 05/08Technical Support 1-800-527-5527 www.LiteTouch.com
WARNING: Read instructions prior to installation or you may VOID THE WARRANTY!
Figure 4
Attach Bracket to Enclosure
Figure 3
Attach Hinge to Bracket
Note: Hinges are installed
into two locations on
both the Enclosure
and Enclosure Lid.
Figure 5
Attach Hinge to Lid
Figure 2
Hinge & Latch Install to Enclosure Lid
Figure 6
Attach Latch to Lid
Figure 7
Latch Fully Assembled & Attached to Lid
LITETOUCH ENCLOSURE LID INSTALLATION
Male Hinge
(2580-120)
Hinge Bracket
(2580-064)
Male Hinge
(2580-120)
Hinge Bracket
(2580-064)
Enclosure
Enclosure
Enclosure
Lid
Latch
Installation
Location
Female Hinge
(2580-122)
Hinge
Installation
Locations
Enclosure
Figure 1
Hinge Install to Enclosure
Hinge
Installation
Locations
Enclosure
Lid
Latch
Assembly
Screws
10-32 x 3/8
(5150-934)
Screws
10-32 x 3/8
(5150-934)
Latch (2580-120)
Enclosure
Lid
Latch
(2580-120)
Enclosure
Lid
Secure Lid
Locations
Figure 6
SURFACE MOUNT ENCLOSURE
Install Hinge to Enclosure (See Figures 1, 3 & 4)
1. Attach Male Hinge (2580-120) to Hinge Bracket (2580-064) using two, 10-32 x 3/8 Pan Head Screws (5150-934).
2. Attach Hinge Brackets to Enclosure, in two places using two, 10-32 x 3/8 Pan Head Screws (5150-934).
Install Hinge to Enclosure Lid (See Figures 2 & 5)
3. Attach Female Hinge (2580-122) to Enclosure, in two places to Lid using two, 10-32 x 3/8 Pan Head Screws (5150-934).
Install Latch to Enclosure Lid (See Figures 2, 6 & 7)
4. Insert Latch (2580-120) through allocated cutout in Enclosure Lid; two small dimples on Latch should face outside.
5. Secure Enclosure Lid closed with two black screws (5150-600). Use two holes above and below Latch.
6900-790.01
Revised 05/08Technical Support 1-800-527-5527 www.LiteTouch.com
WARNING: Read instructions prior to installation or you may VOID THE WARRANTY!
Figure 4
Attach Bracket to Enclosure
Figure 3
Attach Hinge to Bracket
Note: Hinges are installed
into two locations on
both the Enclosure
and Enclosure Lid.
Figure 5
Attach Hinge to Lid
Figure 2
Hinge & Latch Install to Enclosure Lid
Figure 6
Attach Latch to Lid
Figure 7
Latch Fully Assembled & Attached to Lid
LITETOUCH ENCLOSURE LID INSTALLATION
Male Hinge
(2580-120)
Hinge Bracket
(2580-064)
Male Hinge
(2580-120)
Hinge Bracket
(2580-064)
Enclosure
Enclosure
Enclosure
Lid
Latch
Installation
Location
Female Hinge
(2580-122)
Hinge
Installation
Locations
Enclosure
Figure 1
Hinge Install to Enclosure
Hinge
Installation
Locations
Enclosure
Lid
Latch
Assembly
Screws
10-32 x 3/8
(5150-934)
Screws
10-32 x 3/8
(5150-934)
Latch (2580-120)
Enclosure
Lid
Latch
(2580-120)
Enclosure
Lid
Secure Lid
Locations
Figure 7
SmartLighting Recess Mount
Enclosure Lid
(ENC-R4LID and ENC-R2LID)
Quick Reference Guide
009-0764-00
ENC-R4LID-00
ENC-R2LID-00
100912
Copyright © 2012 Savant Systems, LLC. SAVANT and RacePoint Blueprint are trademarks of Savant Systems, LLC.
All brand names, product names and trademarks are the property of their respective owners.
Savant Systems, LLC reserves the right to change product specifications without notice.
  • Page 1 1
  • Page 2 2

Savant ENC-R2LID-00 Reference guide

Savant
Brand
Savant
Model
ENC-R2LID-00
Type
Reference guide
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents