The Savant SmartLighting Surface Mount Enclosure Lid, ENC-S4LID for the four-module
enclosure and ENC-S2LID for the two-module enclosure Quick Reference Guide provides
installation information for both models.
Box Contents
(1) Surface Mount Enclosure Lid for 4-modules (ENC-S4LID-xx)
(1) Surface Mount Hardware Kit for 4 modules (075-8090-020)
•
(1) Enclosure Door Latch (015-2580-120)
•
(2) Enclosure Hinge (015-2580-122)
•
(2) Screw 6-32 x 0.375” TRS HD MB (039-5150-600)
•
(12) Screw 10-32 x 3/8 PN-PN-INT SEMS MS (039-5150-934)
•
(2) Hinge Bracket (071-2580-090)
Or
(1) Surface Mount Enclosure Lid for 2-modules (ENC-S2LID-xx)
(1) Surface Mount Hardware Kit for 2modules (075-8090-020)
•
(1) Enclosure Door Latch (015-2580-120)
•
(2) Enclosure Hinge (015-2580-122)
•
(2) Screw 6-32 x 0.375” TRS HD MB (039-5150-600)
•
(12) Screw 10-32 x 3/8 PN-PN-INT SEMS MS (039-5150-934)
•
(2) Hinge Bracket (071-2580-090)
(1) Quick Reference Guide (this document)
System Components
Four-module Enclosure Box (ENC-4000-xx)
Two-module Enclosure Box (ENC-2000-xx)
Specifications
Environmental
Environmental
Temperature
32° to 95° F (0° to 35° C) - Ambient Operating
Surface Mount Lid - Dimensions and Weight (ENC-S4LID)
Surface Mount Lid - Dimensions and Weight (ENC-S4LID)
Height
36.8 in/93.47 cm
Width
20.6 in/52.32 cm
Depth
0.128 in/0.325 cm
Weight
3.78 lb/1.71 kg
Surface Mount Lid - Dimensions and Weight (ENC-S2LID)
Surface Mount Lid - Dimensions and Weight (ENC-S2LID)
Height
19.98 in/50.50 cm
Width
19.82 in/50.34 cm
Depth
4.0 in/10.16 cm
Weight
2.32 lb/1.05 kg
SURFACE MOUNT ENCLOSURE
Install Hinge to Enclosure (See Figures 1, 3 & 4)
1. Attach Male Hinge (2580-120) to Hinge Bracket (2580-064) using two, 10-32 x 3/8 Pan Head Screws (5150-934).
2. Attach Hinge Brackets to Enclosure, in two places using two, 10-32 x 3/8 Pan Head Screws (5150-934).
Install Hinge to Enclosure Lid (See Figures 2 & 5)
3. Attach Female Hinge (2580-122) to Enclosure, in two places to Lid using two, 10-32 x 3/8 Pan Head Screws (5150-934).
Install Latch to Enclosure Lid (See Figures 2, 6 & 7)
4. Insert Latch (2580-120) through allocated cutout in Enclosure Lid; two small dimples on Latch should face outside.
5. Secure Enclosure Lid closed with two black screws (5150-600). Use two holes above and below Latch.
6900-790.01
Revised 05/08Technical Support 1-800-527-5527 www.LiteTouch.com
WARNING: Read instructions prior to installation or you may VOID THE WARRANTY!
Figure 4
Attach Bracket to Enclosure
Figure 3
Attach Hinge to Bracket
Note: Hinges are installed
into two locations on
both the Enclosure
and Enclosure Lid.
Figure 5
Attach Hinge to Lid
Figure 2
Hinge & Latch Install to Enclosure Lid
Figure 6
Attach Latch to Lid
Figure 7
Latch Fully Assembled & Attached to Lid
LITETOUCH ENCLOSURE LID INSTALLATION
Male Hinge
(2580-120)
Hinge Bracket
(2580-064)
Male Hinge
(2580-120)
Hinge Bracket
(2580-064)
Enclosure
Enclosure
Enclosure
Lid
Latch
Installation
Location
Female Hinge
(2580-122)
Hinge
Installation
Locations
Enclosure
Figure 1
Hinge Install to Enclosure
Hinge
Installation
Locations
Enclosure
Lid
Latch
Assembly
Screws
10-32 x 3/8
(5150-934)
Screws
10-32 x 3/8
(5150-934)
Latch (2580-120)
Enclosure
Lid
Latch
(2580-120)
Enclosure
Lid
Secure Lid
Locations
Surface Mount Enclosure Lid
Refer to Pre-Installation Instructions for SmartLighting Systems (009-0763-xx)
CAUTION: In accordance with CSA requirements, the interior space isolates line and low-voltage sections, and this isolation must be maintained. Place Savant enclosures in an environment in which
ambient temperatures are between 32°F and 95°F. Modules may create some noise and should not be located where this may be objectionable.
Installation Instructions
Enclosures can be installed before or after wiring.
NOTE: Hinges are installed into two locations on both the Enclosure and Enclosure Lid.
1. Install Hinge to Enclosure (See Figures 1, 2 and 3)
a. Attach male hinge to hinge bracket using two pan head screws.
b. Attach hinge brackets to enclosure in two places using two pan head screws.
2. Install Hinge to Enclosure Lid (See Figures 4 and 5)
a. Attach female hinge to lid on top of side edge using two pan head screws.
b. Attach female hinge to lid on bottom of side edge using two pan head screws.
3. Insert Latch to Enclosure Lid (See Figures 6 and 7)
a. Insert latch through allocated cutout in enclosure lid: two small dimples on latch should face outside.
b. Secure enclosure lid closed with two black screws. Use holes above and below latch.
SmartLighting Surface Mount
Enclosure Lid
(ENC-S4LID and ENC-S2LID)
Quick Reference Guide
009-0765-00
ENC-S4LID-00
ENC-S2LID-00
100912
1. Install Hinge to Enclosure
SURFACE MOUNT ENCLOSURE
Install Hinge to Enclosure (See Figures 1, 3 & 4)
1. Attach Male Hinge (2580-120) to Hinge Bracket (2580-064) using two, 10-32 x 3/8 Pan Head Screws (5150-934).
2. Attach Hinge Brackets to Enclosure, in two places using two, 10-32 x 3/8 Pan Head Screws (5150-934).
Install Hinge to Enclosure Lid (See Figures 2 & 5)
3. Attach Female Hinge (2580-122) to Enclosure, in two places to Lid using two, 10-32 x 3/8 Pan Head Screws (5150-934).
Install Latch to Enclosure Lid (See Figures 2, 6 & 7)
4. Insert Latch (2580-120) through allocated cutout in Enclosure Lid; two small dimples on Latch should face outside.
5. Secure Enclosure Lid closed with two black screws (5150-600). Use two holes above and below Latch.
6900-790.01
Revised 05/08Technical Support 1-800-527-5527 www.LiteTouch.com
WARNING: Read instructions prior to installation or you may VOID THE WARRANTY!
Figure 4
Attach Bracket to Enclosure
Figure 3
Attach Hinge to Bracket
Note: Hinges are installed
into two locations on
both the Enclosure
and Enclosure Lid.
Figure 5
Attach Hinge to Lid
Figure 2
Hinge & Latch Install to Enclosure Lid
Figure 6
Attach Latch to Lid
Figure 7
Latch Fully Assembled & Attached to Lid
LITETOUCH ENCLOSURE LID INSTALLATION
Male Hinge
(2580-120)
Hinge Bracket
(2580-064)
Male Hinge
(2580-120)
Hinge Bracket
(2580-064)
Enclosure
Enclosure
Enclosure
Lid
Latch
Installation
Location
Female Hinge
(2580-122)
Hinge
Installation
Locations
Enclosure
Figure 1
Hinge Install to Enclosure
Hinge
Installation
Locations
Enclosure
Lid
Latch
Assembly
Screws
10-32 x 3/8
(5150-934)
Screws
10-32 x 3/8
(5150-934)
Latch (2580-120)
Enclosure
Lid
Latch
(2580-120)
Enclosure
Lid
Secure Lid
Locations
Figure 1
SURFACE MOUNT ENCLOSURE
Install Hinge to Enclosure (See Figures 1, 3 & 4)
1. Attach Male Hinge (2580-120) to Hinge Bracket (2580-064) using two, 10-32 x 3/8 Pan Head Screws (5150-934).
2. Attach Hinge Brackets to Enclosure, in two places using two, 10-32 x 3/8 Pan Head Screws (5150-934).
Install Hinge to Enclosure Lid (See Figures 2 & 5)
3. Attach Female Hinge (2580-122) to Enclosure, in two places to Lid using two, 10-32 x 3/8 Pan Head Screws (5150-934).
Install Latch to Enclosure Lid (See Figures 2, 6 & 7)
4. Insert Latch (2580-120) through allocated cutout in Enclosure Lid; two small dimples on Latch should face outside.
5. Secure Enclosure Lid closed with two black screws (5150-600). Use two holes above and below Latch.
6900-790.01
Revised 05/08Technical Support 1-800-527-5527 www.LiteTouch.com
WARNING: Read instructions prior to installation or you may VOID THE WARRANTY!
Figure 4
Attach Bracket to Enclosure
Figure 3
Attach Hinge to Bracket
Note: Hinges are installed
into two locations on
both the Enclosure
and Enclosure Lid.
Figure 5
Attach Hinge to Lid
Figure 2
Hinge & Latch Install to Enclosure Lid
Figure 6
Attach Latch to Lid
Figure 7
Latch Fully Assembled & Attached to Lid
LITETOUCH ENCLOSURE LID INSTALLATION
Male Hinge
(2580-120)
Hinge Bracket
(2580-064)
Male Hinge
(2580-120)
Hinge Bracket
(2580-064)
Enclosure
Enclosure
Enclosure
Lid
Latch
Installation
Location
Female Hinge
(2580-122)
Hinge
Installation
Locations
Enclosure
Figure 1
Hinge Install to Enclosure
Hinge
Installation
Locations
Enclosure
Lid
Latch
Assembly
Screws
10-32 x 3/8
(5150-934)
Screws
10-32 x 3/8
(5150-934)
Latch (2580-120)
Enclosure
Lid
Latch
(2580-120)
Enclosure
Lid
Secure Lid
Locations
Figure 2
SURFACE MOUNT ENCLOSURE
Install Hinge to Enclosure (See Figures 1, 3 & 4)
1. Attach Male Hinge (2580-120) to Hinge Bracket (2580-064) using two, 10-32 x 3/8 Pan Head Screws (5150-934).
2. Attach Hinge Brackets to Enclosure, in two places using two, 10-32 x 3/8 Pan Head Screws (5150-934).
Install Hinge to Enclosure Lid (See Figures 2 & 5)
3. Attach Female Hinge (2580-122) to Enclosure, in two places to Lid using two, 10-32 x 3/8 Pan Head Screws (5150-934).
Install Latch to Enclosure Lid (See Figures 2, 6 & 7)
4. Insert Latch (2580-120) through allocated cutout in Enclosure Lid; two small dimples on Latch should face outside.
5. Secure Enclosure Lid closed with two black screws (5150-600). Use two holes above and below Latch.
6900-790.01
Revised 05/08Technical Support 1-800-527-5527 www.LiteTouch.com
WARNING: Read instructions prior to installation or you may VOID THE WARRANTY!
Figure 4
Attach Bracket to Enclosure
Figure 3
Attach Hinge to Bracket
Note: Hinges are installed
into two locations on
both the Enclosure
and Enclosure Lid.
Figure 5
Attach Hinge to Lid
Figure 2
Hinge & Latch Install to Enclosure Lid
Figure 6
Attach Latch to Lid
Figure 7
Latch Fully Assembled & Attached to Lid
LITETOUCH ENCLOSURE LID INSTALLATION
Male Hinge
(2580-120)
Hinge Bracket
(2580-064)
Male Hinge
(2580-120)
Hinge Bracket
(2580-064)
Enclosure
Enclosure
Enclosure
Lid
Latch
Installation
Location
Female Hinge
(2580-122)
Hinge
Installation
Locations
Enclosure
Figure 1
Hinge Install to Enclosure
Hinge
Installation
Locations
Enclosure
Lid
Latch
Assembly
Screws
10-32 x 3/8
(5150-934)
Screws
10-32 x 3/8
(5150-934)
Latch (2580-120)
Enclosure
Lid
Latch
(2580-120)
Enclosure
Lid
Secure Lid
Locations
Figure 3
SURFACE MOUNT ENCLOSURE
Install Hinge to Enclosure (See Figures 1, 3 & 4)
1. Attach Male Hinge (2580-120) to Hinge Bracket (2580-064) using two, 10-32 x 3/8 Pan Head Screws (5150-934).
2. Attach Hinge Brackets to Enclosure, in two places using two, 10-32 x 3/8 Pan Head Screws (5150-934).
Install Hinge to Enclosure Lid (See Figures 2 & 5)
3. Attach Female Hinge (2580-122) to Enclosure, in two places to Lid using two, 10-32 x 3/8 Pan Head Screws (5150-934).
Install Latch to Enclosure Lid (See Figures 2, 6 & 7)
4. Insert Latch (2580-120) through allocated cutout in Enclosure Lid; two small dimples on Latch should face outside.
5. Secure Enclosure Lid closed with two black screws (5150-600). Use two holes above and below Latch.
6900-790.01
Revised 05/08Technical Support 1-800-527-5527 www.LiteTouch.com
WARNING: Read instructions prior to installation or you may VOID THE WARRANTY!
Figure 4
Attach Bracket to Enclosure
Figure 3
Attach Hinge to Bracket
Note: Hinges are installed
into two locations on
both the Enclosure
and Enclosure Lid.
Figure 5
Attach Hinge to Lid
Figure 2
Hinge & Latch Install to Enclosure Lid
Figure 6
Attach Latch to Lid
Figure 7
Latch Fully Assembled & Attached to Lid
LITETOUCH ENCLOSURE LID INSTALLATION
Male Hinge
(2580-120)
Hinge Bracket
(2580-064)
Male Hinge
(2580-120)
Hinge Bracket
(2580-064)
Enclosure
Enclosure
Enclosure
Lid
Latch
Installation
Location
Female Hinge
(2580-122)
Hinge
Installation
Locations
Enclosure
Figure 1
Hinge Install to Enclosure
Hinge
Installation
Locations
Enclosure
Lid
Latch
Assembly
Screws
10-32 x 3/8
(5150-934)
Screws
10-32 x 3/8
(5150-934)
Latch (2580-120)
Enclosure
Lid
Latch
(2580-120)
Enclosure
Lid
Secure Lid
Locations
Figure 4
SURFACE MOUNT ENCLOSURE
Install Hinge to Enclosure (See Figures 1, 3 & 4)
1. Attach Male Hinge (2580-120) to Hinge Bracket (2580-064) using two, 10-32 x 3/8 Pan Head Screws (5150-934).
2. Attach Hinge Brackets to Enclosure, in two places using two, 10-32 x 3/8 Pan Head Screws (5150-934).
Install Hinge to Enclosure Lid (See Figures 2 & 5)
3. Attach Female Hinge (2580-122) to Enclosure, in two places to Lid using two, 10-32 x 3/8 Pan Head Screws (5150-934).
Install Latch to Enclosure Lid (See Figures 2, 6 & 7)
4. Insert Latch (2580-120) through allocated cutout in Enclosure Lid; two small dimples on Latch should face outside.
5. Secure Enclosure Lid closed with two black screws (5150-600). Use two holes above and below Latch.
6900-790.01
Revised 05/08Technical Support 1-800-527-5527 www.LiteTouch.com
WARNING: Read instructions prior to installation or you may VOID THE WARRANTY!
Figure 4
Attach Bracket to Enclosure
Figure 3
Attach Hinge to Bracket
Note: Hinges are installed
into two locations on
both the Enclosure
and Enclosure Lid.
Figure 5
Attach Hinge to Lid
Figure 2
Hinge & Latch Install to Enclosure Lid
Figure 6
Attach Latch to Lid
Figure 7
Latch Fully Assembled & Attached to Lid
LITETOUCH ENCLOSURE LID INSTALLATION
Male Hinge
(2580-120)
Hinge Bracket
(2580-064)
Male Hinge
(2580-120)
Hinge Bracket
(2580-064)
Enclosure
Enclosure
Enclosure
Lid
Latch
Installation
Location
Female Hinge
(2580-122)
Hinge
Installation
Locations
Enclosure
Figure 1
Hinge Install to Enclosure
Hinge
Installation
Locations
Enclosure
Lid
Latch
Assembly
Screws
10-32 x 3/8
(5150-934)
Screws
10-32 x 3/8
(5150-934)
Latch (2580-120)
Enclosure
Lid
Latch
(2580-120)
Enclosure
Lid
Secure Lid
Locations
Figure 5
SURFACE MOUNT ENCLOSURE
Install Hinge to Enclosure (See Figures 1, 3 & 4)
1. Attach Male Hinge (2580-120) to Hinge Bracket (2580-064) using two, 10-32 x 3/8 Pan Head Screws (5150-934).
2. Attach Hinge Brackets to Enclosure, in two places using two, 10-32 x 3/8 Pan Head Screws (5150-934).
Install Hinge to Enclosure Lid (See Figures 2 & 5)
3. Attach Female Hinge (2580-122) to Enclosure, in two places to Lid using two, 10-32 x 3/8 Pan Head Screws (5150-934).
Install Latch to Enclosure Lid (See Figures 2, 6 & 7)
4. Insert Latch (2580-120) through allocated cutout in Enclosure Lid; two small dimples on Latch should face outside.
5. Secure Enclosure Lid closed with two black screws (5150-600). Use two holes above and below Latch.
6900-790.01
Revised 05/08Technical Support 1-800-527-5527 www.LiteTouch.com
WARNING: Read instructions prior to installation or you may VOID THE WARRANTY!
Figure 4
Attach Bracket to Enclosure
Figure 3
Attach Hinge to Bracket
Note: Hinges are installed
into two locations on
both the Enclosure
and Enclosure Lid.
Figure 5
Attach Hinge to Lid
Figure 2
Hinge & Latch Install to Enclosure Lid
Figure 6
Attach Latch to Lid
Figure 7
Latch Fully Assembled & Attached to Lid
LITETOUCH ENCLOSURE LID INSTALLATION
Male Hinge
(2580-120)
Hinge Bracket
(2580-064)
Male Hinge
(2580-120)
Hinge Bracket
(2580-064)
Enclosure
Enclosure
Enclosure
Lid
Latch
Installation
Location
Female Hinge
(2580-122)
Hinge
Installation
Locations
Enclosure
Figure 1
Hinge Install to Enclosure
Hinge
Installation
Locations
Enclosure
Lid
Latch
Assembly
Screws
10-32 x 3/8
(5150-934)
Screws
10-32 x 3/8
(5150-934)
Latch (2580-120)
Enclosure
Lid
Latch
(2580-120)
Enclosure
Lid
Secure Lid
Locations
Figure 6
SURFACE MOUNT ENCLOSURE
Install Hinge to Enclosure (See Figures 1, 3 & 4)
1. Attach Male Hinge (2580-120) to Hinge Bracket (2580-064) using two, 10-32 x 3/8 Pan Head Screws (5150-934).
2. Attach Hinge Brackets to Enclosure, in two places using two, 10-32 x 3/8 Pan Head Screws (5150-934).
Install Hinge to Enclosure Lid (See Figures 2 & 5)
3. Attach Female Hinge (2580-122) to Enclosure, in two places to Lid using two, 10-32 x 3/8 Pan Head Screws (5150-934).
Install Latch to Enclosure Lid (See Figures 2, 6 & 7)
4. Insert Latch (2580-120) through allocated cutout in Enclosure Lid; two small dimples on Latch should face outside.
5. Secure Enclosure Lid closed with two black screws (5150-600). Use two holes above and below Latch.
6900-790.01
Revised 05/08Technical Support 1-800-527-5527 www.LiteTouch.com
WARNING: Read instructions prior to installation or you may VOID THE WARRANTY!
Figure 4
Attach Bracket to Enclosure
Figure 3
Attach Hinge to Bracket
Note: Hinges are installed
into two locations on
both the Enclosure
and Enclosure Lid.
Figure 5
Attach Hinge to Lid
Figure 2
Hinge & Latch Install to Enclosure Lid
Figure 6
Attach Latch to Lid
Figure 7
Latch Fully Assembled & Attached to Lid
LITETOUCH ENCLOSURE LID INSTALLATION
Male Hinge
(2580-120)
Hinge Bracket
(2580-064)
Male Hinge
(2580-120)
Hinge Bracket
(2580-064)
Enclosure
Enclosure
Enclosure
Lid
Latch
Installation
Location
Female Hinge
(2580-122)
Hinge
Installation
Locations
Enclosure
Figure 1
Hinge Install to Enclosure
Hinge
Installation
Locations
Enclosure
Lid
Latch
Assembly
Screws
10-32 x 3/8
(5150-934)
Screws
10-32 x 3/8
(5150-934)
Latch (2580-120)
Enclosure
Lid
Latch
(2580-120)
Enclosure
Lid
Secure Lid
Locations
Figure 7
2. Install Hinge to Enclosure Lid
SURFACE MOUNT ENCLOSURE
Install Hinge to Enclosure (See Figures 1, 3 & 4)
1. Attach Male Hinge (2580-120) to Hinge Bracket (2580-064) using two, 10-32 x 3/8 Pan Head Screws (5150-934).
2. Attach Hinge Brackets to Enclosure, in two places using two, 10-32 x 3/8 Pan Head Screws (5150-934).
Install Hinge to Enclosure Lid (See Figures 2 & 5)
3. Attach Female Hinge (2580-122) to Enclosure, in two places to Lid using two, 10-32 x 3/8 Pan Head Screws (5150-934).
Install Latch to Enclosure Lid (See Figures 2, 6 & 7)
4. Insert Latch (2580-120) through allocated cutout in Enclosure Lid; two small dimples on Latch should face outside.
5. Secure Enclosure Lid closed with two black screws (5150-600). Use two holes above and below Latch.
6900-790.01
Revised 05/08Technical Support 1-800-527-5527 www.LiteTouch.com
WARNING: Read instructions prior to installation or you may VOID THE WARRANTY!
Figure 4
Attach Bracket to Enclosure
Figure 3
Attach Hinge to Bracket
Note: Hinges are installed
into two locations on
both the Enclosure
and Enclosure Lid.
Figure 5
Attach Hinge to Lid
Figure 2
Hinge & Latch Install to Enclosure Lid
Figure 6
Attach Latch to Lid
Figure 7
Latch Fully Assembled & Attached to Lid
LITETOUCH ENCLOSURE LID INSTALLATION
Male Hinge
(2580-120)
Hinge Bracket
(2580-064)
Male Hinge
(2580-120)
Hinge Bracket
(2580-064)
Enclosure
Enclosure
Enclosure
Lid
Latch
Installation
Location
Female Hinge
(2580-122)
Hinge
Installation
Locations
Enclosure
Figure 1
Hinge Install to Enclosure
Hinge
Installation
Locations
Enclosure
Lid
Latch
Assembly
Screws
10-32 x 3/8
(5150-934)
Screws
10-32 x 3/8
(5150-934)
Latch (2580-120)
Enclosure
Lid
Latch
(2580-120)
Enclosure
Lid
Secure Lid
Locations
Figure 4
SURFACE MOUNT ENCLOSURE
Install Hinge to Enclosure (See Figures 1, 3 & 4)
1. Attach Male Hinge (2580-120) to Hinge Bracket (2580-064) using two, 10-32 x 3/8 Pan Head Screws (5150-934).
2. Attach Hinge Brackets to Enclosure, in two places using two, 10-32 x 3/8 Pan Head Screws (5150-934).
Install Hinge to Enclosure Lid (See Figures 2 & 5)
3. Attach Female Hinge (2580-122) to Enclosure, in two places to Lid using two, 10-32 x 3/8 Pan Head Screws (5150-934).
Install Latch to Enclosure Lid (See Figures 2, 6 & 7)
4. Insert Latch (2580-120) through allocated cutout in Enclosure Lid; two small dimples on Latch should face outside.
5. Secure Enclosure Lid closed with two black screws (5150-600). Use two holes above and below Latch.
6900-790.01
Revised 05/08Technical Support 1-800-527-5527 www.LiteTouch.com
WARNING: Read instructions prior to installation or you may VOID THE WARRANTY!
Figure 4
Attach Bracket to Enclosure
Figure 3
Attach Hinge to Bracket
Note: Hinges are installed
into two locations on
both the Enclosure
and Enclosure Lid.
Figure 5
Attach Hinge to Lid
Figure 2
Hinge & Latch Install to Enclosure Lid
Figure 6
Attach Latch to Lid
Figure 7
Latch Fully Assembled & Attached to Lid
LITETOUCH ENCLOSURE LID INSTALLATION
Male Hinge
(2580-120)
Hinge Bracket
(2580-064)
Male Hinge
(2580-120)
Hinge Bracket
(2580-064)
Enclosure
Enclosure
Enclosure
Lid
Latch
Installation
Location
Female Hinge
(2580-122)
Hinge
Installation
Locations
Enclosure
Figure 1
Hinge Install to Enclosure
Hinge
Installation
Locations
Enclosure
Lid
Latch
Assembly
Screws
10-32 x 3/8
(5150-934)
Screws
10-32 x 3/8
(5150-934)
Latch (2580-120)
Enclosure
Lid
Latch
(2580-120)
Enclosure
Lid
Secure Lid
Locations
Figure 5
6900-791.00
Revised 05/08Technical Support 1-800-527-5527 www.LiteTouch.com
WARNING: Read instructions prior to installation or you may VOID THE WARRANTY!
Figure 4
Attach Enclosure Trim To Enclosure
Figure 3
Attach Hinge to Enclosure Trim
Note: Hinges are installed
in two locations on
both the Enclosure
Trim and Lid.
Enclosure Trim is
installed in three
locations
Figure 5
Attach Hinge to Lid
Figure 2
Hinge & Latch Install to Enclosure Lid
Figure 6
Attach Latch to Lid
Figure 7
Latch Fully Assembled & Attached to Lid
LITETOUCH ENCLOSURE LID INSTALLATION
Male Hinge
(2580-120)
Male Hinge
(2580-120)
Hinge Spacer
(2580-072)
Enclosure Trim
(2580-070)
Enclosure
Enclosure
Lid
Latch
Installation
Location
Female Hinge
(2580-122)
Hinge
Installation
Locations
Enclosure
Figure 1
Hinge Install to Enclosure
Hinge
Installation
Locations
Enclosure
Lid
Latch
Assembly
Screws
10-32 x 1/2
(5150-960)
Screws
10-32 x 38
(5150-934)
Latch (2580-120)
Enclosure
Lid
Latch
(2580-120)
Enclosure
Lid
RECESS MOUNT ENCLOSURE
Install Hinge and Trim to Enclosure (See Figures 1, 3 & 4)
1. Attach Male Hinge (2580-120) and Hinge Spacer (2580-072) to Enclosure Trim, in two places, using two, 10-32 x 1/2 Flat Head
Screws (5150-960).
2. Attach assembled Enclosure Trim to Enclosure with 6-32 x3/8 Flat Head Screws (5150-619).
Install Hinge to Enclosure Lid (See Figures 2 & 5)
3. Attach Female Hinge (2580-122) to Enclosure Lid using two, 10-32 x 3/8 Pan Head Screws (5150-934).
Install Latch to Enclosure Lid (See Figures 2, 6 & 7)
4. Insert Latch (2580-120) through allocated cutout in Enclosure Lid; two small dimples on Latch should face outside.
5. Secure Enclosure Lid closed with two black screws (5150-600). Use two holes above and below Latch.
Enclosure
Trim
(2580-070)
Secure Lid
Locations
Screws
6-32 x 3/8
(5150-619)
Figure 2
6900-791.00
Revised 05/08Technical Support 1-800-527-5527 www.LiteTouch.com
WARNING: Read instructions prior to installation or you may VOID THE WARRANTY!
Figure 4
Attach Enclosure Trim To Enclosure
Figure 3
Attach Hinge to Enclosure Trim
Note: Hinges are installed
in two locations on
both the Enclosure
Trim and Lid.
Enclosure Trim is
installed in three
locations
Figure 5
Attach Hinge to Lid
Figure 2
Hinge & Latch Install to Enclosure Lid
Figure 6
Attach Latch to Lid
Figure 7
Latch Fully Assembled & Attached to Lid
LITETOUCH ENCLOSURE LID INSTALLATION
Male Hinge
(2580-120)
Male Hinge
(2580-120)
Hinge Spacer
(2580-072)
Enclosure Trim
(2580-070)
Enclosure
Enclosure
Lid
Latch
Installation
Location
Female Hinge
(2580-122)
Hinge
Installation
Locations
Enclosure
Figure 1
Hinge Install to Enclosure
Hinge
Installation
Locations
Enclosure
Lid
Latch
Assembly
Screws
10-32 x 1/2
(5150-960)
Screws
10-32 x 38
(5150-934)
Latch (2580-120)
Enclosure
Lid
Latch
(2580-120)
Enclosure
Lid
RECESS MOUNT ENCLOSURE
Install Hinge and Trim to Enclosure (See Figures 1, 3 & 4)
1. Attach Male Hinge (2580-120) and Hinge Spacer (2580-072) to Enclosure Trim, in two places, using two, 10-32 x 1/2 Flat Head
Screws (5150-960).
2. Attach assembled Enclosure Trim to Enclosure with 6-32 x3/8 Flat Head Screws (5150-619).
Install Hinge to Enclosure Lid (See Figures 2 & 5)
3. Attach Female Hinge (2580-122) to Enclosure Lid using two, 10-32 x 3/8 Pan Head Screws (5150-934).
Install Latch to Enclosure Lid (See Figures 2, 6 & 7)
4. Insert Latch (2580-120) through allocated cutout in Enclosure Lid; two small dimples on Latch should face outside.
5. Secure Enclosure Lid closed with two black screws (5150-600). Use two holes above and below Latch.
Enclosure
Trim
(2580-070)
Secure Lid
Locations
Screws
6-32 x 3/8
(5150-619)
Figure 3
6900-791.00
Revised 05/08Technical Support 1-800-527-5527 www.LiteTouch.com
WARNING: Read instructions prior to installation or you may VOID THE WARRANTY!
Figure 4
Attach Enclosure Trim To Enclosure
Figure 3
Attach Hinge to Enclosure Trim
Note: Hinges are installed
in two locations on
both the Enclosure
Trim and Lid.
Enclosure Trim is
installed in three
locations
Figure 5
Attach Hinge to Lid
Figure 2
Hinge & Latch Install to Enclosure Lid
Figure 6
Attach Latch to Lid
Figure 7
Latch Fully Assembled & Attached to Lid
LITETOUCH ENCLOSURE LID INSTALLATION
Male Hinge
(2580-120)
Male Hinge
(2580-120)
Hinge Spacer
(2580-072)
Enclosure Trim
(2580-070)
Enclosure
Enclosure
Lid
Latch
Installation
Location
Female Hinge
(2580-122)
Hinge
Installation
Locations
Enclosure
Figure 1
Hinge Install to Enclosure
Hinge
Installation
Locations
Enclosure
Lid
Latch
Assembly
Screws
10-32 x 1/2
(5150-960)
Screws
10-32 x 38
(5150-934)
Latch (2580-120)
Enclosure
Lid
Latch
(2580-120)
Enclosure
Lid
RECESS MOUNT ENCLOSURE
Install Hinge and Trim to Enclosure (See Figures 1, 3 & 4)
1. Attach Male Hinge (2580-120) and Hinge Spacer (2580-072) to Enclosure Trim, in two places, using two, 10-32 x 1/2 Flat Head
Screws (5150-960).
2. Attach assembled Enclosure Trim to Enclosure with 6-32 x3/8 Flat Head Screws (5150-619).
Install Hinge to Enclosure Lid (See Figures 2 & 5)
3. Attach Female Hinge (2580-122) to Enclosure Lid using two, 10-32 x 3/8 Pan Head Screws (5150-934).
Install Latch to Enclosure Lid (See Figures 2, 6 & 7)
4. Insert Latch (2580-120) through allocated cutout in Enclosure Lid; two small dimples on Latch should face outside.
5. Secure Enclosure Lid closed with two black screws (5150-600). Use two holes above and below Latch.
Enclosure
Trim
(2580-070)
Secure Lid
Locations
Screws
6-32 x 3/8
(5150-619)
Figure 1
3. Install Latch to Enclosure Lid
SURFACE MOUNT ENCLOSURE
Install Hinge to Enclosure (See Figures 1, 3 & 4)
1. Attach Male Hinge (2580-120) to Hinge Bracket (2580-064) using two, 10-32 x 3/8 Pan Head Screws (5150-934).
2. Attach Hinge Brackets to Enclosure, in two places using two, 10-32 x 3/8 Pan Head Screws (5150-934).
Install Hinge to Enclosure Lid (See Figures 2 & 5)
3. Attach Female Hinge (2580-122) to Enclosure, in two places to Lid using two, 10-32 x 3/8 Pan Head Screws (5150-934).
Install Latch to Enclosure Lid (See Figures 2, 6 & 7)
4. Insert Latch (2580-120) through allocated cutout in Enclosure Lid; two small dimples on Latch should face outside.
5. Secure Enclosure Lid closed with two black screws (5150-600). Use two holes above and below Latch.
6900-790.01
Revised 05/08Technical Support 1-800-527-5527 www.LiteTouch.com
WARNING: Read instructions prior to installation or you may VOID THE WARRANTY!
Figure 4
Attach Bracket to Enclosure
Figure 3
Attach Hinge to Bracket
Note: Hinges are installed
into two locations on
both the Enclosure
and Enclosure Lid.
Figure 5
Attach Hinge to Lid
Figure 2
Hinge & Latch Install to Enclosure Lid
Figure 6
Attach Latch to Lid
Figure 7
Latch Fully Assembled & Attached to Lid
LITETOUCH ENCLOSURE LID INSTALLATION
Male Hinge
(2580-120)
Hinge Bracket
(2580-064)
Male Hinge
(2580-120)
Hinge Bracket
(2580-064)
Enclosure
Enclosure
Enclosure
Lid
Latch
Installation
Location
Female Hinge
(2580-122)
Hinge
Installation
Locations
Enclosure
Figure 1
Hinge Install to Enclosure
Hinge
Installation
Locations
Enclosure
Lid
Latch
Assembly
Screws
10-32 x 3/8
(5150-934)
Screws
10-32 x 3/8
(5150-934)
Latch (2580-120)
Enclosure
Lid
Latch
(2580-120)
Enclosure
Lid
Secure Lid
Locations
Figure 1
SURFACE MOUNT ENCLOSURE
Install Hinge to Enclosure (See Figures 1, 3 & 4)
1. Attach Male Hinge (2580-120) to Hinge Bracket (2580-064) using two, 10-32 x 3/8 Pan Head Screws (5150-934).
2. Attach Hinge Brackets to Enclosure, in two places using two, 10-32 x 3/8 Pan Head Screws (5150-934).
Install Hinge to Enclosure Lid (See Figures 2 & 5)
3. Attach Female Hinge (2580-122) to Enclosure, in two places to Lid using two, 10-32 x 3/8 Pan Head Screws (5150-934).
Install Latch to Enclosure Lid (See Figures 2, 6 & 7)
4. Insert Latch (2580-120) through allocated cutout in Enclosure Lid; two small dimples on Latch should face outside.
5. Secure Enclosure Lid closed with two black screws (5150-600). Use two holes above and below Latch.
6900-790.01
Revised 05/08Technical Support 1-800-527-5527 www.LiteTouch.com
WARNING: Read instructions prior to installation or you may VOID THE WARRANTY!
Figure 4
Attach Bracket to Enclosure
Figure 3
Attach Hinge to Bracket
Note: Hinges are installed
into two locations on
both the Enclosure
and Enclosure Lid.
Figure 5
Attach Hinge to Lid
Figure 2
Hinge & Latch Install to Enclosure Lid
Figure 6
Attach Latch to Lid
Figure 7
Latch Fully Assembled & Attached to Lid
LITETOUCH ENCLOSURE LID INSTALLATION
Male Hinge
(2580-120)
Hinge Bracket
(2580-064)
Male Hinge
(2580-120)
Hinge Bracket
(2580-064)
Enclosure
Enclosure
Enclosure
Lid
Latch
Installation
Location
Female Hinge
(2580-122)
Hinge
Installation
Locations
Enclosure
Figure 1
Hinge Install to Enclosure
Hinge
Installation
Locations
Enclosure
Lid
Latch
Assembly
Screws
10-32 x 3/8
(5150-934)
Screws
10-32 x 3/8
(5150-934)
Latch (2580-120)
Enclosure
Lid
Latch
(2580-120)
Enclosure
Lid
Secure Lid
Locations
Figure 2
SURFACE MOUNT ENCLOSURE
Install Hinge to Enclosure (See Figures 1, 3 & 4)
1. Attach Male Hinge (2580-120) to Hinge Bracket (2580-064) using two, 10-32 x 3/8 Pan Head Screws (5150-934).
2. Attach Hinge Brackets to Enclosure, in two places using two, 10-32 x 3/8 Pan Head Screws (5150-934).
Install Hinge to Enclosure Lid (See Figures 2 & 5)
3. Attach Female Hinge (2580-122) to Enclosure, in two places to Lid using two, 10-32 x 3/8 Pan Head Screws (5150-934).
Install Latch to Enclosure Lid (See Figures 2, 6 & 7)
4. Insert Latch (2580-120) through allocated cutout in Enclosure Lid; two small dimples on Latch should face outside.
5. Secure Enclosure Lid closed with two black screws (5150-600). Use two holes above and below Latch.
6900-790.01
Revised 05/08Technical Support 1-800-527-5527 www.LiteTouch.com
WARNING: Read instructions prior to installation or you may VOID THE WARRANTY!
Figure 4
Attach Bracket to Enclosure
Figure 3
Attach Hinge to Bracket
Note: Hinges are installed
into two locations on
both the Enclosure
and Enclosure Lid.
Figure 5
Attach Hinge to Lid
Figure 2
Hinge & Latch Install to Enclosure Lid
Figure 6
Attach Latch to Lid
Figure 7
Latch Fully Assembled & Attached to Lid
LITETOUCH ENCLOSURE LID INSTALLATION
Male Hinge
(2580-120)
Hinge Bracket
(2580-064)
Male Hinge
(2580-120)
Hinge Bracket
(2580-064)
Enclosure
Enclosure
Enclosure
Lid
Latch
Installation
Location
Female Hinge
(2580-122)
Hinge
Installation
Locations
Enclosure
Figure 1
Hinge Install to Enclosure
Hinge
Installation
Locations
Enclosure
Lid
Latch
Assembly
Screws
10-32 x 3/8
(5150-934)
Screws
10-32 x 3/8
(5150-934)
Latch (2580-120)
Enclosure
Lid
Latch
(2580-120)
Enclosure
Lid
Secure Lid
Locations
Figure 3
SURFACE MOUNT ENCLOSURE
Install Hinge to Enclosure (See Figures 1, 3 & 4)
1. Attach Male Hinge (2580-120) to Hinge Bracket (2580-064) using two, 10-32 x 3/8 Pan Head Screws (5150-934).
2. Attach Hinge Brackets to Enclosure, in two places using two, 10-32 x 3/8 Pan Head Screws (5150-934).
Install Hinge to Enclosure Lid (See Figures 2 & 5)
3. Attach Female Hinge (2580-122) to Enclosure, in two places to Lid using two, 10-32 x 3/8 Pan Head Screws (5150-934).
Install Latch to Enclosure Lid (See Figures 2, 6 & 7)
4. Insert Latch (2580-120) through allocated cutout in Enclosure Lid; two small dimples on Latch should face outside.
5. Secure Enclosure Lid closed with two black screws (5150-600). Use two holes above and below Latch.
6900-790.01
Revised 05/08Technical Support 1-800-527-5527 www.LiteTouch.com
WARNING: Read instructions prior to installation or you may VOID THE WARRANTY!
Figure 4
Attach Bracket to Enclosure
Figure 3
Attach Hinge to Bracket
Note: Hinges are installed
into two locations on
both the Enclosure
and Enclosure Lid.
Figure 5
Attach Hinge to Lid
Figure 2
Hinge & Latch Install to Enclosure Lid
Figure 6
Attach Latch to Lid
Figure 7
Latch Fully Assembled & Attached to Lid
LITETOUCH ENCLOSURE LID INSTALLATION
Male Hinge
(2580-120)
Hinge Bracket
(2580-064)
Male Hinge
(2580-120)
Hinge Bracket
(2580-064)
Enclosure
Enclosure
Enclosure
Lid
Latch
Installation
Location
Female Hinge
(2580-122)
Hinge
Installation
Locations
Enclosure
Figure 1
Hinge Install to Enclosure
Hinge
Installation
Locations
Enclosure
Lid
Latch
Assembly
Screws
10-32 x 3/8
(5150-934)
Screws
10-32 x 3/8
(5150-934)
Latch (2580-120)
Enclosure
Lid
Latch
(2580-120)
Enclosure
Lid
Secure Lid
Locations
Figure 4
SURFACE MOUNT ENCLOSURE
Install Hinge to Enclosure (See Figures 1, 3 & 4)
1. Attach Male Hinge (2580-120) to Hinge Bracket (2580-064) using two, 10-32 x 3/8 Pan Head Screws (5150-934).
2. Attach Hinge Brackets to Enclosure, in two places using two, 10-32 x 3/8 Pan Head Screws (5150-934).
Install Hinge to Enclosure Lid (See Figures 2 & 5)
3. Attach Female Hinge (2580-122) to Enclosure, in two places to Lid using two, 10-32 x 3/8 Pan Head Screws (5150-934).
Install Latch to Enclosure Lid (See Figures 2, 6 & 7)
4. Insert Latch (2580-120) through allocated cutout in Enclosure Lid; two small dimples on Latch should face outside.
5. Secure Enclosure Lid closed with two black screws (5150-600). Use two holes above and below Latch.
6900-790.01
Revised 05/08Technical Support 1-800-527-5527 www.LiteTouch.com
WARNING: Read instructions prior to installation or you may VOID THE WARRANTY!
Figure 4
Attach Bracket to Enclosure
Figure 3
Attach Hinge to Bracket
Note: Hinges are installed
into two locations on
both the Enclosure
and Enclosure Lid.
Figure 5
Attach Hinge to Lid
Figure 2
Hinge & Latch Install to Enclosure Lid
Figure 6
Attach Latch to Lid
Figure 7
Latch Fully Assembled & Attached to Lid
LITETOUCH ENCLOSURE LID INSTALLATION
Male Hinge
(2580-120)
Hinge Bracket
(2580-064)
Male Hinge
(2580-120)
Hinge Bracket
(2580-064)
Enclosure
Enclosure
Enclosure
Lid
Latch
Installation
Location
Female Hinge
(2580-122)
Hinge
Installation
Locations
Enclosure
Figure 1
Hinge Install to Enclosure
Hinge
Installation
Locations
Enclosure
Lid
Latch
Assembly
Screws
10-32 x 3/8
(5150-934)
Screws
10-32 x 3/8
(5150-934)
Latch (2580-120)
Enclosure
Lid
Latch
(2580-120)
Enclosure
Lid
Secure Lid
Locations
Figure 5
SURFACE MOUNT ENCLOSURE
Install Hinge to Enclosure (See Figures 1, 3 & 4)
1. Attach Male Hinge (2580-120) to Hinge Bracket (2580-064) using two, 10-32 x 3/8 Pan Head Screws (5150-934).
2. Attach Hinge Brackets to Enclosure, in two places using two, 10-32 x 3/8 Pan Head Screws (5150-934).
Install Hinge to Enclosure Lid (See Figures 2 & 5)
3. Attach Female Hinge (2580-122) to Enclosure, in two places to Lid using two, 10-32 x 3/8 Pan Head Screws (5150-934).
Install Latch to Enclosure Lid (See Figures 2, 6 & 7)
4. Insert Latch (2580-120) through allocated cutout in Enclosure Lid; two small dimples on Latch should face outside.
5. Secure Enclosure Lid closed with two black screws (5150-600). Use two holes above and below Latch.
6900-790.01
Revised 05/08Technical Support 1-800-527-5527 www.LiteTouch.com
WARNING: Read instructions prior to installation or you may VOID THE WARRANTY!
Figure 4
Attach Bracket to Enclosure
Figure 3
Attach Hinge to Bracket
Note: Hinges are installed
into two locations on
both the Enclosure
and Enclosure Lid.
Figure 5
Attach Hinge to Lid
Figure 2
Hinge & Latch Install to Enclosure Lid
Figure 6
Attach Latch to Lid
Figure 7
Latch Fully Assembled & Attached to Lid
LITETOUCH ENCLOSURE LID INSTALLATION
Male Hinge
(2580-120)
Hinge Bracket
(2580-064)
Male Hinge
(2580-120)
Hinge Bracket
(2580-064)
Enclosure
Enclosure
Enclosure
Lid
Latch
Installation
Location
Female Hinge
(2580-122)
Hinge
Installation
Locations
Enclosure
Figure 1
Hinge Install to Enclosure
Hinge
Installation
Locations
Enclosure
Lid
Latch
Assembly
Screws
10-32 x 3/8
(5150-934)
Screws
10-32 x 3/8
(5150-934)
Latch (2580-120)
Enclosure
Lid
Latch
(2580-120)
Enclosure
Lid
Secure Lid
Locations
Figure 6
SURFACE MOUNT ENCLOSURE
Install Hinge to Enclosure (See Figures 1, 3 & 4)
1. Attach Male Hinge (2580-120) to Hinge Bracket (2580-064) using two, 10-32 x 3/8 Pan Head Screws (5150-934).
2. Attach Hinge Brackets to Enclosure, in two places using two, 10-32 x 3/8 Pan Head Screws (5150-934).
Install Hinge to Enclosure Lid (See Figures 2 & 5)
3. Attach Female Hinge (2580-122) to Enclosure, in two places to Lid using two, 10-32 x 3/8 Pan Head Screws (5150-934).
Install Latch to Enclosure Lid (See Figures 2, 6 & 7)
4. Insert Latch (2580-120) through allocated cutout in Enclosure Lid; two small dimples on Latch should face outside.
5. Secure Enclosure Lid closed with two black screws (5150-600). Use two holes above and below Latch.
6900-790.01
Revised 05/08Technical Support 1-800-527-5527 www.LiteTouch.com
WARNING: Read instructions prior to installation or you may VOID THE WARRANTY!
Figure 4
Attach Bracket to Enclosure
Figure 3
Attach Hinge to Bracket
Note: Hinges are installed
into two locations on
both the Enclosure
and Enclosure Lid.
Figure 5
Attach Hinge to Lid
Figure 2
Hinge & Latch Install to Enclosure Lid
Figure 6
Attach Latch to Lid
Figure 7
Latch Fully Assembled & Attached to Lid
LITETOUCH ENCLOSURE LID INSTALLATION
Male Hinge
(2580-120)
Hinge Bracket
(2580-064)
Male Hinge
(2580-120)
Hinge Bracket
(2580-064)
Enclosure
Enclosure
Enclosure
Lid
Latch
Installation
Location
Female Hinge
(2580-122)
Hinge
Installation
Locations
Enclosure
Figure 1
Hinge Install to Enclosure
Hinge
Installation
Locations
Enclosure
Lid
Latch
Assembly
Screws
10-32 x 3/8
(5150-934)
Screws
10-32 x 3/8
(5150-934)
Latch (2580-120)
Enclosure
Lid
Latch
(2580-120)
Enclosure
Lid
Secure Lid
Locations
Figure 7
SmartLighting Surface Mount
Enclosure Lid
(ENC-S4LID and ENC-S2LID)
Quick Reference Guide
009-0765-00
ENC-S4LID-00
ENC-S2LID-00
100912
Copyright © 2012 Savant Systems, LLC. SAVANT and RacePoint Blueprint are trademarks of Savant Systems, LLC.
All brand names, product names and trademarks are the property of their respective owners.
Savant Systems, LLC reserves the right to change product specifications without notice.
/
