The Savant SmartLighting Box, ENC-4000, Quick Reference Guide provides information for the
four-module enclosure box.
Box Contents
(1) Enclosure Box for 4 modules (ENC-4000-xx)
(1) Quick Reference Guide (this document)
System Accessories
Four-module Enclosure Recessed Mount Lid (ENC-R4LID-xx)
Four-module Enclosure Surface Mount Lid (ENC-S4LID-xx)
Enclosure Diagnostic Bus Monitor (ENC-BM01-xx)
Enclosure Ground Bar (ENC-GBAR-xx)
Enclosure Neutral Bar (ENC-NBAR-xx)
Enclosure Transorb Board (ENC-TRANS-xx)
Specifications
Environmental
Environmental
Temperature
32° to 95° F (0° to 35° C) - Ambient Operating
Four Module Enclosure - Dimensions and Weight
Four Module Enclosure - Dimensions and Weight
Height
37 in/93.98 cm
Width
20 in/50.80 cm
Depth
4.0 in/10.16 cm
Weight
5.94 lb/2.69 kg
Compliance
Compliance
Safety and Emissions
UL | ETL
RoHS
Compliant
A. Power Supply Installation
1. The power supply module mounts in the enclosure as specified on the enclosure
schedule and is available as a single power supply or dual (two) in one module. Each
power supply requires a maximum 5 amps of input power from the circuit breaker panel.
2. Do not put more than 4 power supplies on one circuit. Please refer to enclosure
schedule for locations of the power supplies.
B. Power Supply Requirements for LV Relay Module
1. One power supply will drive a maximum of 10
LV Relay modules.
2. Use two 16 gauge wires for power supply connections. A power supply connector is
provided with each
LV Relay module.
Make sure positive is connected to positive, etc.
C. Power Supply Requirements for CCU & Stations
1. All stations
and data-inputs
are connected parallel to the CCU. The power supply connection for stations are made inside the CCU.
2. Run two 16 gauge wires for each power supply. Connection is made to one of the available “Station” Terminals on the
CCU. Do not connect more than one power supplies to one Station Port.
3. Standard and Compact CCUs require connection to power supply module. CCU must be within 50’ of power supply
4. Each keypad terminat at the CCU requires a power supply in order for the keypad(s) on that Terminal port to operate. In small systems,
jumping the power supply at the CCU is acceptable.
5. One non-backlit Keypad draws a max of 65 mA by default, one backlit Keypad draws a max of 150 mA by default (because of the
backlit engraving). See LiteTouch specification sheets for variation based upon keypad style.
EQUIPMENT
INSTALLATION
Transorb
Board
Barrier
Neutral
Bars
Low Voltage
Side
Line Voltage
Side
Ground
Bar
Transorb
Board
Barrier
Neutral
Bars
Low Voltage
Side
Line Voltage
Side
Ground
Bar
Dual Power Supply
6800-218
U
L
®
LISTED
71TO
IND. CONT. EQ.
®
LR50210
3550 SO. 700 WEST • SLC., UTAH 84119 • (801) 268-8668 • FAX (801) 268-9200 • TECH HOT LINE 1-800-527-5527
WARNING
A SHORTED LOAD WILL DAMAGE MODULE.
THIS IS NOT COVERED BY WARRANTY.
TO AVOID POSSIBLE DAMAGE TO MODULE
AC POWER MUST BE REMOVED BEFORE
CONNECTING OR DISCONNECTING LOADS.
Rated 2 Amps 15 Volts Max.
Neutral
120 VAC
60 HZ
Neutral
120 VAC
60 HZ
WIRE RANGE 10-16 AWG. / TORQUE 10-12 IN. LBS. / 60 c MIN. COPPER WIRE ONLY
POWER
DC Pos.
DC Com.
FUSE AGC 5 Amp.
NOT USED
POWER
DC Pos.
DC Com.
FUSE AGC 5 Amp.
NOT USED
®
Power supply connection is required
for Low Voltage Relay Module.
Dimmers and relay modules have
built-in power and do not require
connection to the power supply.
Enclosures may be ordered for recess/flush or surface mounting and
can be mounted two or more units high. Each enclosure contains a
barrier to isolate high voltage from low voltage. Keep these wires on
their respective side of the enclosure.
Do not cross over or under the barrier with wires.
A. Flush Mount Enclosure - mount enclosure to wall studs using
screw holes located on side panels of enclosure. Leave 3”
minimum space between enclosures to accommodate
recess/flush mount lids.
B. Surface Mount Enclosure - mount enclosure to wall using screw
holes located on back panel of enclosure.
Install all enclosures before proceeding with step 2.
STEP 1.
ENCLOSURE INSTALLATION
STEP 2.
POWER SUPPLY INSTALLATION
3
A. Power Supply Installation
1. The power supply module mounts in the enclosure as specified on the enclosure
schedule and is available as a single power supply or dual (two) in one module. Each
power supply requires a maximum 5 amps of input power from the circuit breaker panel.
2. Do not put more than 4 power supplies on one circuit. Please refer to enclosure
schedule for locations of the power supplies.
B. Power Supply Requirements for LV Relay Module
1. One power supply will drive a maximum of 10
LV Relay modules.
2. Use two 16 gauge wires for power supply connections. A power supply connector is
provided with each
LV Relay module.
Make sure positive is connected to positive, etc.
C. Power Supply Requirements for CCU & Stations
1. All stations
and data-inputs
are connected parallel to the CCU. The power supply connection for stations are made inside the CCU.
2. Run two 16 gauge wires for each power supply. Connection is made to one of the available “Station” Terminals on the
CCU. Do not connect more than one power supplies to one Station Port.
3. Standard and Compact CCUs require connection to power supply module. CCU must be within 50’ of power supply
4. Each keypad terminat at the CCU requires a power supply in order for the keypad(s) on that Terminal port to operate. In small systems,
jumping the power supply at the CCU is acceptable.
5. One non-backlit Keypad draws a max of 65 mA by default, one backlit Keypad draws a max of 150 mA by default (because of the
backlit engraving). See LiteTouch specification sheets for variation based upon keypad style.
EQUIPMENT
INSTALLATION
Transorb
Board
Barrier
Neutral
Bars
Low Voltage
Side
Line Voltage
Side
Ground
Bar
Transorb
Board
Barrier
Neutral
Bars
Low Voltage
Side
Line Voltage
Side
Ground
Bar
Dual Power Supply
6800-218
U
L
®
LISTED
71TO
IND. CONT. EQ.
®
LR50210
3550 SO. 700 WEST • SLC., UTAH 84119 • (801) 268-8668 • FAX (801) 268-9200 • TECH HOT LINE 1-800-527-5527
WARNING
A SHORTED LOAD WILL DAMAGE MODULE.
THIS IS NOT COVERED BY WARRANTY.
TO AVOID POSSIBLE DAMAGE TO MODULE
AC POWER MUST BE REMOVED BEFORE
CONNECTING OR DISCONNECTING LOADS.
Rated 2 Amps 15 Volts Max.
Neutral
120 VAC
60 HZ
Neutral
120 VAC
60 HZ
WIRE RANGE 10-16 AWG. / TORQUE 10-12 IN. LBS. / 60 c MIN. COPPER WIRE ONLY
POWER
DC Pos.
DC Com.
FUSE AGC 5 Amp.
NOT USED
POWER
DC Pos.
DC Com.
FUSE AGC 5 Amp.
NOT USED
®
Power supply connection is required
for Low Voltage Relay Module.
Dimmers and relay modules have
built-in power and do not require
connection to the power supply.
Enclosures may be ordered for recess/flush or surface mounting and
can be mounted two or more units high. Each enclosure contains a
barrier to isolate high voltage from low voltage. Keep these wires on
their respective side of the enclosure.
Do not cross over or under the barrier with wires.
A. Flush Mount Enclosure - mount enclosure to wall studs using
screw holes located on side panels of enclosure. Leave 3”
minimum space between enclosures to accommodate
recess/flush mount lids.
B. Surface Mount Enclosure - mount enclosure to wall using screw
holes located on back panel of enclosure.
Install all enclosures before proceeding with step 2.
STEP 1.
ENCLOSURE INSTALLATION
STEP 2.
POWER SUPPLY INSTALLATION
3
Four Module Enclosure
Enclosure Installation
Enclosures may be ordered for surface- or recess-mounting and can be mounted two or more
units high.Each enclosure contains a barrier to isolate high voltage from low voltage.
CAUTION: Keep these wires on their respective side of the enclosure. Do not cross over
or under the voltage barrier with wires.
Recess- or Flush-Mount Enclosure (ENC-R4LID)
1. Mount enclosure to wall studs using screw holes located on the side panels of the
enclosure.
2. Leave 3 inches minimum space between each enclosure to accommodate the recess/flush
lids .
3. Install all enclosures before connecting the power.
Surface Mount Enclosure (ENC-S4LID)
1. Mount enclosure to wall using screw holes located on the back panel of the enclosure.
2. Install all enclosures before connecting the power.
SmartLighting Enclosure Box
(ENC-4000)
Quick Reference Guide
009-0741-00
ENC-4000-00
Copyright © 2012 Savant Systems, LLC. SAVANT and RacePoint Blueprint are trademarks of Savant Systems, LLC.
All brand names, product names and trademarks are the property of their respective owners.
Savant Systems, LLC reserves the right to change product specifications without notice.
100412
/
