Lytecaster Conventional Frames & Trims

Lightolier Lytecaster Conventional Frames & Trims, 3 3/4” Incandescent IC Insulated Ceiling Frame-In Kit, Lytecaster Frames Install Instructions

  • Hello! I am an AI chatbot trained to assist you with the Lightolier Lytecaster Conventional Frames & Trims Install Instructions. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
  • How to prevent electric shock while installing the Lightolier Lytecaster Conventional Frames & Trims?
    Where can I find the maintenance reference for the Lightolier Lytecaster Conventional Frames & Trims?
    What is the maximum number of AWG branch circuit conductors suitable for the junction box?
    How to attach the mounting frame to a wood joist?
    How to connect the fixture wires to the supply leads?
    What is the maximum height of the mounting frame above the ceiling line for suspended ceiling applications?
    How to cut the hole in the ceiling for the fixture?
    What is the recommended accessory for wet plaster ceilings?
\,
\,
T,
READANB UNDERSTANDTHESEINSTRUCTIONS BEFOREINSTALLINGFIXTURE
INSTRUCTION
SHEET NO.
his
fixtureisintendedforinstallationinaccordancewiththeNationalElectricalCodeandlocalregulations,
oassurefull compliancewith localcodesandregulations,check with yourlocaleiastricalinspectorbafore
IS:2000IC
)stelletion.Topreventelectricalshock,turnoff elactrici~ at fuse box bafore pmcaeding,
Retein theao instructionsfor meintmrance reference.
UB94 Page 1 ef 1
INSTAIIATIONPROCEDUREFOR FRAME-IN KIT 20001C AND 2000AIC
r~
MO
NCTION BOX MAX. OF
#12 AWG BflANCH CIRCUIT
NDUCTORSSUITABLEFOR
NOTEI.C. Frsme-in Kit may ba used indirect contact with
insulation.
1. FRAME-IN
AND WIRE-IN
Fasten MOUNTING FRAME to wood joist. Lina up bottom edge of
ADJUSTABLE MOUNTING BAR with bottom of wood joist (Fig, 1).
Wire to supply leads. (For cable, uaa built-in cabla clamp in J-BOX.)
Whita fixtura lead to neutral supply Iaad. Black fixture lead to hot
(120V.)
supply lead. Bara fixture wire to supPlY ground. Use wiranuts
(local hardwara items), Placa all electrical connections in the J-BOX.
Attach J-BOX COVER onto
J-BOX.
.’” “M, ., .,,
ATI FASTWPPFRMITFnIN
.. ----- .. . ..
JUCTION aOX
ING BAR
MOUN
M EOGE
OFWOOI
NOTE ADJUSTABLE MOUNTING BARS can be extanded for 24
mounting. For suspanded ceiling, make certain that the bottom of
FIG.1
MOUNTING FRAME is no higher than 1“ above ceiling he (Fig. 2).
2.
CLOSE-IN
Install in plasterboard or other dy~pe ceiling, as requirad. Hola in
board can be cut either on the floor or after the board is nailed to the
ceiling, using MOUNTING FRAME opening as cutting guida. (Make sure
ROTO-CLIPSara rotated out of hole araa to be cut.)
11
NOTE For wet plastar ceiling, use Plastar Ring Accessory No. 1959
(order separately),
3. SNAP-IN
}
SEESEPARATEREFLECTOR
t
4.
PUSH-UP
TRIMINSTRUCTIONSHEET.
WARNING: USEONLYWITH LIGHT.OLIERREFLECTORTRIMS
MARKEDWITH I.C.LAMPINGINFORMATION.
~ ‘lGz
WARNING:
USE ONLY WITH TRIMS DESIGNATED BY
MANUFACTUREilS’ TRIMS VOLIOS THE
UNDERWRITERS LABORATORIES LISTING AND
M C5HTC>M El?
SECAUCUS, NEW JERSEY 07096
MONTREAL, QUEBEC, CANAOA
/