Lightolier IS:1102T User manual

Brand: Lightolier

Model: IS:1102T

Type: User manual

Lightolier IS:1102T is a compact fluorescent frame-in kit, designed for recessed installation in suspended ceiling systems or wood joist/metal stud constructions. It is intended for residential and commercial applications and can be used to create a variety of lighting effects, including general illumination, accent lighting, and wall washing.

The kit includes adjustable mounting bars, a J-Box for electrical connections, and a mounting frame that can be used as a guide for cutting a hole in the ceiling material. The mounting bars can be repositioned to accommodate different fixture openings, and locking screws are provided to lock the bars in place once they have been positioned.

READ AND UNDERSTAND THESE INSTRUCTIONS BEFORE INSTALLING FIXTURE.

This fixture is intended for installation in accordance with the National Electrical Code and local or Federal

code specifications. To assure full compliance with codes and regulations, check with your local electrical

inspector before installation. To prevent electrical shock, turn off electricity at fuse box before proceeding.

Retain these instructions for maintenance reference.

LIGHTOLIER a GENLYTE THOMAS company.

631 Airport Road, Fall River, MA 02720

INSTRUCTION SHEET NO.

IS:1102T

E0403 Page 1 of 2

Instructions for Compact Fluorescent Frame-In Kit Installation

WARNING – (RISK OF FIRE)

Do not install insulation within 3 inches of fixture sides or wiring

compartments, nor above fixture in such a manner as to entrap heat.

LOCKING SCREW

CENTERING

SLOTS

ADJUSTABLE

MOUNTING

BARS

MOUNTING

FRAME

ROTO CLIP

CEILING MATERIAL

Fig. C Fig. D

Fig. A

FRAME-IN

A. WOOD JOIST/METAL STUD CONSTRUCTION

1. Position Frame-In Kit opening.* Mounting bars can be

repositioned to narrow side of frame if required to

locate fixture opening as desired. Extend mounting

bars, line up bottom edge of bars with bottom of wood

joist/metal stud and nail in place. For metal stud (Fig.

A2), fasten with machine screws through holes in the

mounting bars. Locking screws are provided to lock

mounting bars in place once positioned properly (Fig. A).

2. For multiple fixture installations, use centered slots as

guides to align adjacent fixture (Fig. A).

B. SUSPENDED CEILING SYSTEM

1. Position Frame-In Kit opening.* Mounting bars can be

repositioned to narrow side of frame if required to

locate fixture opening as desired. Extend mounting

bars, until notched opening fits on top of T-Bar.

(NOTE: Make certain that the bottom of the mounting

frame is no higher than 1” above the ceiling line).

2. Lock mounting bars by bending tab underneath T-Bar

bead (Fig. B1), or by using screws for round T-Bar bead

(Fig. B2).

WIRE-IN

1. White fixture leads to neutral (white) supply lead.

Black fixture leads to hot (black) supply leads.

Bare copper and/or green insulated wire(s) must all be

connected to supply ground. Use wirenuts for splices

(local hardware item). Place all electrical connections

in the J-Box.

2. For ROMEX or BX cable use built-in cable clamp in

J-Box.

CLOSE-IN

1. Install plasterboard or other dry type ceiling.

2. Hole in plasterboard can be cut by using mounting

frame opening as a guide (Fig. C) (make sure roto clips

are rotated counterclockwise out of the hole area, see

Fig. D).

3. For wet plaster ceilings, use plaster Ring Accessory

No. 1961 (ordered separately).

* See Page 2 for Frame-In Kit installation when using

wall washer trim (1135).

LINE UP BOTTOM EDGE

WITH BOTTOM OF WOOD

JOIST

MOUNTING

FRAME

MOUNTING BAR

Fig. A1 Fig. A2

See Reflector Trim Instruction Sheet for Trim Installation

Fig. B

1” MAX.

NOTCHED

OPENING

1-1/2” MAX.

ADJUSTABLE

MOUNTING

BARS

T-BAR

WARNING – Use only reflector trims provided by Lightolier. Use of other Manufacturers’ reflector trims voids

the Underwriters Laboratories listing and could constitute a fire hazard.

INSTRUCTION SHEET NO.

IS:1102T

E0403 Page 2 of 2

LIGHTOLIER a GENLYTE THOMAS company.

631 Airport Road, Fall River, MA 02720

READ AND UNDERSTAND THESE INSTRUCTIONS BEFORE INSTALLING FIXTURE.

This fixture is intended for installation in accordance with the National Electrical Code and local or Federal

code specifications. To assure full compliance with codes and regulations, check with your local electrical

inspector before installation. To prevent electrical shock, turn off electricity at fuse box before proceeding.

Retain these instructions for maintenance reference.

BALLAST REPLACEMENT (MAGNETIC VERSION SHOWN)

1. TURN OFF POWER.

2. Remove Reflector Trim from ceiling (see Reflector Trim instructions).

3. Remove Ballast assembly by lifting spring on top of J-Box and

pulling ballast outward (Fig. E).

4. Disconnect all wiring.

5. Replace Ballast on J-Box Cover (see label on old ballast for proper

replacement).

6. Insert ballast assembly through ceiling and rewire fixture (see wire

diagram on ballast label).

7. Reassemble new ballast assembly to J-Box by placing tabs with

slots in J-Box bracket then snap onto spring.

8. Install Reflector Trim.

Frame-In Kit Installation when using

Wall Washer Trim (1135T)

J-BOX ON FACING WALL

WALL WASHER FACE PLATE

TOP VIEW SIDE VIEW

WALL

Fig. E

Black

Blue

Red

White

Red

White

Ballast

White

Yellow

White

Electronic

Ballast

Electronic

Ballast

Wiring Diagram For Magnetic HPF Ballast

All 2-Pin Electronic Ballast

Wiring Diagram For Magnetic NPF Ballast All 4-Pin Electronic Ballast

Lightolier IS:1102T User manual

Lightolier IS:1102T User manual

Lightolier IS:1102T User manual

Related papers

Other documents