Page is loading ...
C50.X2000F.00E-1
Side panel
lock
14cm fans
SAS hot swap
HDD cage
14cm fan
Hardware list
12
for stand off
Buzzer(1)
Screw(30)
for fix HDD
Box(1)
for spare parts
SATA cable(8)
for HDD
for fix CD-ROM
(4)
2
Stand off bolt (3)
Mounting bracket
for SSI CEB/EEB
for cable management
Side panels installation
Remove the side panel. Adding a lock to secure the
hardware.
Loose the screw and pull the
latch to release the side panel.
5.25”
mounting
bracket
3.5”
mounting
bracket
Patented
tool-less
PSU mounting
bracket
14cm fan
Patented
tool-less
PCI add-on card
holder
SAS hot swap
HDD cage
Extension cable 12V (1)
for power supply to M/B
CPU 8pin to 8pin (1)
PCI card holder-S(1)
PCI card holder-L(6)
Thumb screw(7)
for PCI card holder
Power supply unit extender(1)
for fix mount longer PSU
USB3.0 to USB2.0
convertor (1)
Bracket(1)
for power supply mounting
Longer vision thumb screw(3)
for mother board mount
Shorter vision thumb screw(9)
for mother board mount
(5)
for power supply unit extender
(spare parts)
Aluminum HDD rail(7)
Easy clean air filter
Remove air filter
PCI bracket (1)
PSU tray
Secure the stand off bolts on the M/B tray which
match with the M/B fix points, place the M/B on
the copper bolt, fasten the screws to secure.
The oval hole on M/B tray designed
for special server boards, please use
the nut to hold the copper bolt in place
for SSI CEB/EEB
E-SATA
I/O port installation
BLUE
BLACK PUEPLE
YELLOW
BROWN
RED
10
8
6
4
2
9
7
5
3
1
GREEN
KEY
ORANGE
N.C.
GND+H.S. TUBE
HD AUDIO
4
1
5
9
USB3.0
USB USB EARMIC
SATA
USB3.0 to USB2.0 convertor
RED
WHITE
GREEN
BLACK
VCC
D-
D+
GND
RED
WHITE
GREEN
BLACK
KEY
VCC
D-
D+
GND
Access to rear I/O port.
PCI bracket installation
Fan adjustable
device
H
L
Place the water tube
through the rubber cover.
Vents
for water cooling
Rubber (4)
PSU tray installation
Loosing four thumb screws to
remove the PSU mounting bracket.
Assembling the power supply with PSU
mounting bracket, and push in gently.
Fasten four thumb screws onto the case
to secure.
PSU installation
Place the PSU on the stand, and
push again the rear panel.
Place the PSU bracket into
according slot as shown.
Lock the PSU bracket to secure the PSU.
* For transportation, please place screw
to secure the PSU
OPEN
LOCK
VGA Card Pillar Installation Guide
1
2
3
4
PSU unit extender
installation
5.25” mounting bracket can be placed
either on right or left side.
NOTE:
Loosen thumb screws
Slide it out to release
Adding the rubber pad to ODD's
eject bottom, when 5.25" ODD
bezel couldn't reach to the ODD.
CD-ROM installation guide
POWER SW
RESET SW
POWER
LED
H.D.D LED
SPEAKER
WHITE
GRAY
WHITE
BLUE
WHITE
NC
GREEN
WHITE
ORANGE
BLACK
NC
NC
RED
GROUND
PWR
GROUND
Reset
PLED-
PLED+
IDE_LED-
IDE_LED+
Speaker
+5V
Front panel cable
installation guide
PCI Add-on card installation
Finish.
1
2
Open the aluminum latch to
remove the PCI slot bracket.
Loosing two screws to remove the
5.25" mounting bracket
for mount longer PSU
Insert the CD-ROM, fasten
thumb screws to secure.
Fasten two screws to the 5.25"
mounting bracket
Fasten two screws.
Fasten four screws.
Assembling the PSU to PSU unit
extender.
Push the card into the PCI slot,
close the aluminum latch to secure
the card.
/
