Lian Li PC-Z60B Installation guide

Lian Li
Brand
Lian Li
Model
PC-Z60B
Category
Computer cases
Type
Installation guide
Install the screws to the HDD with
anti-vibration rubber slide rail.
Screw (4)
for PSU mounting
Slide the HDD into the HDD cage.
Close the gate to secure the HDD. Lock.
Case components
Installation Guide
2.5" HDD module installation
Power switch
Reset switch
Multi-media ports
Slide the panel backward to
release.
Fasten eight screws.
5.25" mounting bezels
Hardware list
Thumb screw(24)
for HDD
Remove front panel
Screw (20)
for 2.5" HDD/spare parts
Place the M/B on the copper bolt and secure
with thumb screws.
!
Note:
For hard to reach
areas use long
thumb screws.
!
!
Remove four
thumb screws.
Patented tool-less
PSU mounting
bracket
Slide the HDD into the HDD cage.
Pull the front panel towards yourself.
Buzzer (1)
Cable ties (2)
USB 3.0 to USB 2.0
converter (1)
Longer thumb screw (3)
for motherboard mount
Shorter thumb screw (6)
for motherboard mount
3.5” HDD module installation
Rubberized
grommets for
liquid cooling
tubing
120mm fan
Cable management
140mm fan
Removable
120mm fans
with air filter
Rubber slide rail (12)
for HDD
Key is in the
accessories box
Bracket (1)
for power supply mounting
Patented tool-less
PCI add-on card
holder
Patented
tool-less 5.25”
device mounting
Removable
2.5" HDD module
(For 2.5" HDD x 2)
Hot swap
3.5" HDD cage
(For 3.5" HDD x 6)
C50.Z6000.01E-1
USB
POWER SW
RESET SW
POWER
LED
H.D.D LED
SPEAKER
WHITE
GRAY
WHITE
BLUE
WHITE
NC
GREEN
WHITE
ORANGE
BLACK
NC
NC
RED
GROUND
PWR
GROUND
Reset
PLED-
PLED+
IDE_LED-
IDE_LED+
Speaker
+5V
Cable guide installation
SATA
Cable
E-SATA
E-SATA
USB 2.0
USB 3.0
HD AUDIO
BLUE
BLACK PURPLE
YELLOW
BROWN
RED
10
8
6
4
2
9
7
5
3
1
GREEN
KEY
ORANGE
N.C.
GND+H.S. TUBE
USB 3.0 to USB 2.0 converter
Push the ODD into the 5.25” rack.
Close the bracket to
ODD.
secure the
ODD installation
Press the right and left sides of
the bezel to remove.
Press the plastic handle to release
the mounting bracket.
Remove air filter
Rotate washable air filter clockwise to
remove.
Lock the PSU bracket to
secure the PSU.
* For transportation, please use
screws to secure the PSU.
PSU installation
Place the PSU on the stand, and
push against the rear panel.
Place the PSU bracket into the slot
as shown.
1
2
PCI add-on card installation
Open the aluminum latch to remove
the PCI slot bracket.
Push the card into the PCI slot, close
the aluminum latch to secure the card.
Change fan from right-side to left-side
Supports liquid cooling
systems
Slide the fan up to remove. Remove five screws to
release the bracket.
Place the bracket on the
other side, fasten five
screws to secure.
Washable air filter below the PSU
Slide the air filter to remove.
Washable air filter on the right-side
USB 3.0
Supports motherboard
USB 3.0 20 Pin header
USB 3.0
MIC EAR
USB 2.0
Place the fan into the bracket
and slide down to secure.
I/O port installation
C50.Z6000.01E-2
1
20
11
10
RED
GREEN
BLACK
WHITE
VCC
D-
D+
GND
RED
GREEN
BLACK
KEY
WHITE
VCC
D-
D+
GND
USB
  • Page 1 1
  • Page 2 2

Lian Li PC-Z60B Installation guide

Lian Li
Brand
Lian Li
Model
PC-Z60B
Category
Computer cases
Type
Installation guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents