Page is loading ...
C50.X9000.00E-1
Side panels installation
Reset switch button
Power switch button
Power LED
HDD LED
5.25” mounting
bezel
5.25” to 3.5"
convertor
Multi-media port
120mm fans
Patented tool-less 5.25”
device mounting
Patented tool-less PSU
mounting bracket
Rubberized
grommets
for liquid cooling
system’s tubing
Patented tool-less
PCI add-on card holder
120mm fans
Fan controller
Hardware list
(4)
(2)
(12)
Box(1)
for spare parts
Longer vision thumb screw(3)
for mother board mount
Thumb screw(28)
for HDD
Shorter vision thumb screw(6)
for mother board mount
for PSU mounting
Bracket(1)
for power supply mounting
USB3.0 to USB2.0
convertor (1)
PCI bracket (1)
Loose thumb screws to remove the
HDD cage.
Insert HDD, secured with thumb
screws.
Insert the HDD cage to the mounting
position.
3.5" Hard disk installation
Fasten the thumb screw to secure
the HDD cage.
E-SATA
I/O port installation
BLUE
BLACK PUEPLE
YELLOW
BROWN
RED
10
8
6
4
2
9
7
5
3
1
GREEN
KEY
ORANGE
N.C.
GND+H.S. TUBE
HD AUDIO
4
1
5
9
USB3.0
USB USB EARMIC
SATA
USB3.0 to USB2.0 convertor
RED
WHITE
GREEN
BLACK
VCC
D-
D+
GND
RED
WHITE
GREEN
BLACK
KEY
VCC
D-
D+
GND
For access to rear I/O port.
PCI bracket installation
SATA cable(2)
for HDD
Fan adjustable device
Remove the side panel. Adding a lock to secure the
hardware.
Loose the screw and pull the
latch to release the side panel.
H
L
PSU tray installation
Removable upper double fan module
Remove the HDD cage for long
PSU.
Loosing screws to remove fan
module.
Follow the arrow to remove the filter, press the
plastic clips to release the washable air filter.
Loosing four thumb screws to
remove the PSU mounting bracket.
Assembling the power supply with
PSU mounting bracket, and push
in gently.
Fasten four thumb screws onto the
case to secure.
ODD installation
4. By pressing plastic
handle to release the
mounting bracket.
5. Push the CD-ROM into the ODD cage
module, close the bracket to secure.
6. Reverse previous steps for installation
bezel & converter.
Adding the rubber pad to ODD's
eject bottom, when 5.25" ODD
bezel couldn't reach to the ODD.
1. Remove the 5.25" to 3.5" converter. 2. Remove the 5.25" ODD
bezel.
3. Slide the 5.25" ODD bezel
downwards to remove it.
If you wish to use the
5.25" ODD bezel,
please adjust the metal
pin position on the
mounting bracket
Secure the stand-off on the M/B tray which match
with the M/B fix points, place the M/B on the
stand-off fasten with the thumb screws to secure.
!
Note:
For area where hard
to reach use the
longer thumb screw
!
!
PCI Add-on card installation
1
2
Open the aluminum latch to
remove the PCI slot bracket.
Push the card into the PCI slot,
close the aluminum latch to secure
the card.
PSU installation
Place the PSU on the stand, and
push again the rear panel.
Place the PSU bracket into
according slot as shown.
Lock the PSU bracket to secure the PSU.
* For transportation, please place screw
to secure the PSU
Place the water tube through
the rabber cover.
Vents for water cooling
C50.X9000.00E-2
/
