Lian Li PC-Z70B Installation guide

Category
Computer cases
Type
Installation guide
1.Close the gate to secure
the HDD.
2.Lock.
3.5” HDD module installation
Slide the HDD into the
HDD cage.
Install the screws to the HDD
with anti-vibration rubber rings.
2.5” HDD module installation
Fasten eight screws.
L
Slide the HDD into the
HDD cage.
ODD installation
Press the right and left sides
of the bezel to remove.
Push the ODD into the 5.25"
rack.
Press the plastic handle to
release the mounting bracket.
1
2
Screw (4)
for PSU mounting
Remove six
thumb screws.
1
2
Close the bracket to secure
the ODD.
Case components
Installation Guide
Slide the panel backward
to release.
Hardware list
Thumb screw(36)
for HDD
Remove four thumb screws, to release
the VGA card support column
Buzzer (1)
Cable ties (2)
USB 3.0 to USB 2.0
converter
Longer thumb screw (3)
for motherboard mount
Shorter thumb screw (9)
for motherboard mount
140mm fans x 2
Removable
120mm fans
with air filter
Rubber slide rail (18)
for HDD
Rubberized
grommets for
liquid cooling
tubing
120mm fan
Patented tool-less
PSU mounting
bracket
Patented
tool-less 5.25”
device mounting
Removable
2.5" HDD module
(For 2.5" HDD x 2)
Hot swap
3.5" HDD cage
(For 3.5" HDD x 9)
VGA card
support column
PCI card holder/A (8)
PCI card holder/B (4)
Thumb screw (8)
for PCI card holder
Bracket (1)
for power supply mounting
Nut (3)
for stand off
Stand off bolt (3)
for motherboard (spare parts)
Mounting bracket
for SSI CEB/EEB M/B
Place the M/B on the copper bolt and secure
with thumb screws.
for SSI CEB/EEB
The oval hole on the M/B
tray is designed for special
server boards. Please use
a nut to secure the copper
bolt in place
Note: For hard to reach areas
use long thumb screws.
!
!
!
Screw driver (1)
to ass’y motherboard
Screw (20)
for 2.5" HDD/spare parts
Box (1)
for spare parts
Key is in the
accessories box
Remove front panel
Pull the front panel towards
yourself.
Power switch
Reset switch
Multi-media ports
5.25" mounting bezels
Patented tool-less
PCI add-on card
holder
C50.Z7000.01E-1
USB
POWER SW
RESET SW
POWER
LED
H.D.D LED
SPEAKER
WHITE
GRAY
WHITE
BLUE
WHITE
NC
GREEN
WHITE
ORANGE
BLACK
NC
NC
RED
GROUND
PWR
GROUND
Reset
PLED-
PLED+
IDE_LED-
IDE_LED+
Speaker
+5V
Cable guide installation
USB 3.0 to USB 2.0 converter
Remove air filter
Rotate washable air filter clockwise to
remove.
1
2
PCI add-on card installation
Open the aluminum latch to remove
the PCI slot bracket.
Push the card into the PCI slot, close
the aluminum latch to secure the card.
Change fan from right-side to left-side
Supports liquid cooling
systems
Slide the fan up to remove. Remove six screws to
release the bracket.
Place the bracket on the
other side, fasten six screws
to secure.
Place the fan into the bracket
and slide down to secure.
Washable air filter below the PSU
Slide the air filter to remove.
Washable air filter on the right-side
VGA card pillar installation guide
Use PCI card holder/B for thick VGA cards.
Insert PCI card holder/A
L
Cable management
Lock the PSU bracket to
secure the PSU.
* For transportation, please use
screws to secure the PSU.
PSU installation
Place the PSU on the stand, and
push against the rear panel.
Place the PSU bracket into the slot
as shown.
SATA
Cable
E-SATA
E-SATA
USB 2.0
USB 3.0
HD AUDIO
BLUE
BLACK PURPLE
YELLOW
BROWN
RED
10
8
6
4
2
9
7
5
3
1
GREEN
KEY
ORANGE
N.C.
GND+H.S. TUBE
USB 3.0
Supports motherboard
USB 3.0 20 Pin header
USB 3.0
MIC EAR
USB 2.0
I/O port installation
C50.Z7000.01E-2
1
20
11
10
RED
GREEN
BLACK
WHITE
VCC
D-
D+
GND
RED
GREEN
BLACK
KEY
WHITE
VCC
D-
D+
GND
USB
  • Page 1 1
  • Page 2 2

Lian Li PC-Z70B Installation guide

Category
Computer cases
Type
Installation guide

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI