Lian Li PC-B25SB Datasheet

Brand: Lian Li

Model: PC-B25SB

Category: Computer cases

Type: Datasheet

Lian Li PC-B25SB is a mid-tower case with a 5.25” tool-less device mounting system, a patented tool-less PSU mounting bracket, and a patented tool-less PCI add-on card holder. It supports motherboards up to ATX size and has seven expansion slots. The case comes with one 140mm fan and one 120mm fan, and it has mounts for up to three additional 120mm fans. The front panel has two USB 3.0 ports, two USB 2.0 ports, an eSATA port, and HD audio jacks. The case also has a built-in speaker and a reset button.

Liquid-cooling

system tube vents

rubber cover

C50.B25S0.00E-1

Case components

Side panels installation

Installation Guide

140mm fan

Patented

tool-less 5.25”

device mounting

Patented

tool-less PSU

mounting bracket

Patented

Tool-less PCI

add-on card holder

120mm fan &

fan air duct

Patented

HDD module

Pull the front panel toward

yourself.

Slide the panel backward

to release.

5.25" to 3.5"

convertor

Press the right and left side of the

bezel to remove.

Remove the mounting bezel

Push the ODD into the 5.25” rack,

close the bracket to secare the ODD

ODD installation

Press plastic handle to release the

mounting bracket.

Accessing fan filter

Left the top cover to remove.

Press the handle to release

the washable air filter.

Slide the HDD into the HDD

cage

Hard disk installation guide

Close the gate to secure the

HDD.

Fasten four screws to the

HDD with anti-vibration

rubber rings.

Secure the stand-off on the M/B tray

which match with the M/B fix points,

place the M/B on the stand-off fasten

with the thumb screws to secure.

Note:

For area where hard

to reach use the

long thumb screw

Hardware list

Rubber ring(24)

for HDD mounting

Thumb screw(24)

for HDD mounting

Screw (4)

for power supply mounting

USB3.0 to USB2.0

convertor (1)

PCI bracket (1)

Fan air duct (1)

for fan mount

Bracket(1)

for power supply mounting

Buzzer (1)

Cable tie (2)

Screw (12)

spare parts

Air inlet below PSU

with air filter

Longer vision thumb screw(3)

for mother board mount

Shorter vision thumb screw(6)

for mother board mount

POWER SW

RESET SW

POWER

LED

H.D.D LED

SPEAKER

WHITE

GRAY

WHITE

BLUE

WHITE

GREEN

WHITE

ORANGE

BLACK

RED

GROUND

PWR

GROUND

Reset

PLED-

PLED+

IDE_LED-

IDE_LED+

Speaker

+5V

Front panel cable

installation guide

PCI Add-on card installation

Finish.

Open the aluminum latch to

remove the PCI slot bracket.

Push the card into the PCI slot,

close the aluminum latch to secure

the card.

E-SATA

I/O port installation

BLUE

BLACK PUEPLE

YELLOW

BROWN

RED

GREEN

KEY

ORANGE

N.C.

GND+H.S. TUBE

HD AUDIO

USB3.0

USB3.0 to USB2.0 convertor

RED

WHITE

GREEN

BLACK

VCC

D-

D+

GND

RED

WHITE

GREEN

BLACK

KEY

VCC

D-

D+

GND

Access to rear I/O port.

PCI bracket installation

PSU installation

Place the PSU on the stand, and

push again to the rear panel.

Place the PSU bracket into

according slot as shown.

Lock the PSU bracket to secure

the PSU.

* For transportation, please use

screws to secure the PSU

Remove four thumb screws. Install air duct frame on fan with

four 5x10 screws.

Place the fan air duct into proper

location, fasten four thumb screws.

Loose the thumb screws in order to

adjust the angle .

Fan air duct installation

C50.B25S0.00E-2

Accessing filter

Press the handle

to release the

washable air filter.

Lian Li PC-B25SB Datasheet

Brand: Lian Li

Model: PC-B25SB

Category: Computer cases

Type: Datasheet

Download PDF

report

Lian Li PC-B25SB Datasheet

Lian Li PC-B25SB Datasheet

Related papers

Other documents