Lian Li PC-V2120 Installation guide

Lian Li
Brand
Lian Li
Model
PC-V2120
Category
Computer cases
Type
Installation guide

Lian Li PC-V2120 boasts a rich set of features that will accommodate your needs and allow for various system configurations. It supports motherboards of ATX, Micro-ATX, SSI CEB, and SSI E-EEB form factors. The case provides ample space for expansion cards, including support for up to 7 PCI-E slots. It also offers several options for storage devices, supporting up to 6 3.5-inch or 2.5-inch drives. Additionally, the case has dedicated mounting points for 2.5-inch SSDs.

Lian Li PC-V2120 boasts a rich set of features that will accommodate your needs and allow for various system configurations. It supports motherboards of ATX, Micro-ATX, SSI CEB, and SSI E-EEB form factors. The case provides ample space for expansion cards, including support for up to 7 PCI-E slots. It also offers several options for storage devices, supporting up to 6 3.5-inch or 2.5-inch drives. Additionally, the case has dedicated mounting points for 2.5-inch SSDs.

C50.V2120.02E-1
Case components
Installation Guide
Rubberized grommets
for liquid cooling
system’s tubing
Patented
tool-less 5.25”
device mounting
120mm fan
Removable
3.5” HDD module
Multi-media ports
Hardware list
Longer vision thumb screw(3)
for mother board mount
Thumb screw(54)
for HDD
Rubber ring(50)
for HDD
Shorter vision thumb screw(9)
for mother board mount
Screw(5)
for PSU mounting
USB3.0 to USB2.0
convertor (1)
Screw (20)
for converter & spare parts
5.25" mounting
bezel
Fan controller
Door key is attach to
the accessory box
Front door
with lock
Side panels installation
Remove the side panel. Adding a lock to secure the
hardware.
Loose the screw and pull the
latch to release the side panel.
1
Push to release
Slide the HDD into the HDD
cage
Install the screws to the HDD
with anti-vibration rubber rings
Mounting bracket
for SSI CEB/EEB M/B
PCI card holder/A (11)
Thumb screw(11)
for PCI card holder
Follow the arrow to remove
the fan for HPTX M/B
installation
Converter (1)
3.5" to 2.5" x 2 drive bays
Nut(3)
for stand off
Box(1)
for spare parts
Stand off bolt (3)
for motherboard (spare parts)
Removable
PSU tray
for cable management
Clamp (1)
Thumb screw(1)
Close the gate to secure the
HDD.
Insert HDD, secured with
thumb screws.
3.5” HDD module installation 2.5" HDD installation
Use one
3.5" to 2.5" x 2 converter
Screw (8)
for 2.5” HDD
Buzzer (1)
Cable tie (2)
for cable
Install the screws to the HDD
with anti-vibration rubber rings
Secure the stand-off bolts on the M/B tray which
match with the M/B fix points, place the M/B
on the copper bolt, fasten with the thumb screws
to secure.
for SSI CEB/EEB
The oval hole on M/B tray
designed for special server
boards, please use nut to
hold the copper bolt in place.
Note: For area where hard to
reach use the long
thumb screw
!
!
!
PCI card holder/B (4)
For 2.5" HDD x 2
Removable
120mm fan cover
Notice:
Loosing six
thumb screws
Slide out M/B tray
2.5" HDD module
installation
3.5” HDD module
installation
Removable
fan mounting
Remove 5.25" mounting bezel
2
Air inlet below PSU
with air filter
Removable
front fan & air filter
Side panel lock
140mm fans
with air filter
Power switch
Reset switch
Metal casters
with brake
For 2.5" HDD x1
Removable
3.5” HDD module
For 2.5" HDD x1
Screw (12)
for 2.5” HDD
VGA card pillar
For 2.5" HDD x1
Slide out M/B tray
Vent for USB3.0 cable
HDD can slide into the cage by
either side.
(HDD port in front or back)
Notice:
E-SATA
I/O port installation
BLUE
BLACK PUEPLE
YELLOW
BROWN
RED
10
8
6
4
2
9
7
5
3
1
GREEN
KEY
ORANGE
N.C.
GND+H.S. TUBE
HD AUDIO
4
1
5
9
USB3.0
USB USB EARMIC
SATA
USB3.0 to USB2.0 convertor
RED
WHITE
GREEN
BLACK
VCC
D-
D+
GND
RED
WHITE
GREEN
BLACK
KEY
VCC
D-
D+
GND
PSU tray installation
Loosing four thumb screws to
remove the PSU mounting
bracket.
Assembling the power supply
with PSU mounting bracket, and
push in gently.
Fasten four thumb screws onto the
case to secure.
VGA card pillar installation guide
1
2
3
4
C50.V2120.02E-2
Remove 120mm fan cover
Loosing four screws to remove
the 120mm fan cover in order
to install the optional kit
Remove front fan &
air filter
Fan adjustable device
H
L
Cable management note
Use cable clamp to
tidy up the cables.
Insert PCI card holder/A Place PCI card holder/B for thick VGA card
OPTIONAL KIT:
120mm fan module
* To remove clamp,
release the cable clamp
by using tweezers.
Follow the arrow to remove the
front fan & air filter
Release brake
Follow the arrow to remove the
bottom air filter
Follow the arrow to
release brake
Remove air filter
Change door from right-side-open to left-side-open,
visit www.lian-li.com for installation guide
Notice:
ODD installation
Release the mounting bracket
Push the CD-ROM into the
ODD module
Close the bracket.
Just press plastic handle
POWER SW
RESET SW
POWER
LED
H.D.D LED
SPEAKER
WHITE
GRAY
WHITE
BLUE
WHITE
NC
GREEN
WHITE
ORANGE
BLACK
NC
NC
RED
GROUND
PWR
GROUND
Reset
PLED-
PLED+
IDE_LED-
IDE_LED+
Speaker
+5V
Cable installation guide
Vent for USB3.0 cable
Access to rear I/O port
  • Page 1 1
  • Page 2 2

Lian Li PC-V2120 Installation guide

Lian Li
Brand
Lian Li
Model
PC-V2120
Category
Computer cases
Type
Installation guide

Lian Li PC-V2120 boasts a rich set of features that will accommodate your needs and allow for various system configurations. It supports motherboards of ATX, Micro-ATX, SSI CEB, and SSI E-EEB form factors. The case provides ample space for expansion cards, including support for up to 7 PCI-E slots. It also offers several options for storage devices, supporting up to 6 3.5-inch or 2.5-inch drives. Additionally, the case has dedicated mounting points for 2.5-inch SSDs.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents