Lian Li PC-A77FR Installation guide

Lian Li
Brand
Lian Li
Model
PC-A77FR
Category
Computer cases
Type
Installation guide
Case component
Power switch button
Reset switch button
Multi-media port
5.25”
mounting
bracket
with air filter
Power LED
HDD LED
VGA card
pillar
Removable HDD module
with 140mm fan
C50.A77F0.00E-1
Remove six
thumb screws.
Slide panel backward of the case.
Installation Guide
120mm fan
Patented tool-less 5.25”
device mounting
Patented tool-less PSU
mounting bracket
Rubberized grommets
for liquid cooling
system’s tubing
Patented tool-less
PCI add-on card holder
Press the right and left side of the
bezel to remove.
Remove the mounting bezel
Hardware list
Mounting bracket
for SSI CEB/EEB M/B
(5)
(3)
(18)
Box(1)
for spare parts
Longer vision thumb screw(3)
for mother board mount
for work with stand-off
Thumb screw(24)
for HDD
Thumb screw(1)
Rubber ring(24)
for HDD
Shorter vision thumb screw(9)
for mother board mount
for PSU mounting
Bracket(1)
for power supply mounting
Hex wrench for M/B(1)
stand-off
for cable management
1
Secure the stand-off bolts on the M/B tray which match
with the M/B fix points,place the M/B on the copper bolt,
fasten with the thumb screws to secure.
for SSI CEB/EEB
The oval hole on M/B tray
designed for special server
boards, please use nut to
hold the copper bolt in place.
Note: For area where hard to
reach use the long
thumb screw
!
!
!
POWER SW
RESET SW
POWER
LED
H.D.D LED
SPEAKER
WHITE
GRAY
WHITE
BLUE
WHITE
NC
GREEN
WHITE
ORANGE
BLACK
NC
NC
RED
GROUND
PWR
GROUND
Reset
PLED-
PLED+
IDE_LED-
IDE_LED+
Speaker
+5V
Front panel cable installation guide
Slide the HDD into the front HDD cage
Hard disk installation for the front HDD cage
Close the gate to secure the HDD.
Install the screws to the HDD with
anti-vibration rubber rings.
Push the ODD into the 5.25” rack,
close the bracket to secure the
ODD
ODD installation
1. Pull the front panel to remove it.
2. Release the 5.25" bezel
3. Press plastic handle to release the mounting bracket.
PCI card holder-S(2)
PCI card holder-L(5)
Thumb screw(7)
for PCI card holder
USB3.0 to USB2.0
convertor (1)
140mm fan
PCI bracket (1)
E-SATA
Connector
I/O port installation
PSU installation
Place the PSU on the stand, and
push again the rear panel.
Place the PSU bracket into
according slot as shown.
Lock the PSU bracket to secure
the PSU.
Cable management note
Use cable clamp to tidy up
the cables.
VGA Card Pillar Installation Guide
1
2
3
4
PCI Add-on card installation
Finish.
1
2
Open the aluminum latch to
remove the PCI slot bracket.
Push the card into the PCI slot, close the
aluminum latch to secure the card.
* Remove clamp, use
tweezers to release the
cable clamp
BLUE
BLACK PUEPLE
YELLOW
BROWN
RED
10
8
6
4
2
9
7
5
3
1
GREEN
KEY
ORANGE
N.C.
GND+H.S. TUBE
4
1
5
9
HD AUDIO
USB3.0
USB USB EARMIC
SATA
For access to rear I/O port.
PCI bracket installation
USB3.0 to USB2.0 convertor
RED
WHITE
GREEN
BLACK
VCC
D-
D+
GND
RED
WHITE
GREEN
BLACK
KEY
VCC
D-
D+
GND
C50.A77F0.00E-2
  • Page 1 1
  • Page 2 2

Lian Li PC-A77FR Installation guide

Lian Li
Brand
Lian Li
Model
PC-A77FR
Category
Computer cases
Type
Installation guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents