American Standard 7163.804 User manual

Brand: American Standard

Model: 7163.804

Type: User manual

This manual is also suitable for

G31

SILHOUETTE™ 33"

SHALLOW DOUBLE BOWL SINK

AMERICAST

Revised 2/08

SILHOUETTE™ 33" SHALLOW DOUBLE BOWL

KITCHEN SINK

• Americast

brand engineered material

• Dual level double bowl design

• Titanium enamel - heat resistant up to 1000°

• Acid-resisting glossy porcelain nish

• Top mount or undercounter installation

• Silicone sealant supplied

• Available in 1, 3, 4, or 5 faucet hole conguration

• Customized hole punchings available

(see page G56)

Top Mount/Undercounter:

❏ 7163.001 Center hole only

❏ 7163.803 3 hole

❏ 7163.804 4 hole

❏ 7163.805 5 hole

Nominal Dimensions:

838 x 559 x 152mm

(33" x 22" x 6")

Bowl sizes:

Right Hand: 359mm (14-1/8") wide

413mm (16-1/4") front to back

152mm (6") deep

Left Hand: 359mm (14-1/8") wide

476mm (18-3/4") front to back

152mm (6") deep

Undercounter Installation Order:

❏ 791326-100 Mounting Kit (consists of

cut-out template and mounting clips)

* See faucet section for available models

Compliance Certications -

Meets or Exceeds the Following Specications:

• ASME A112.19.4M for Americast Plumbing Fixtures

• ASTM E162 for Flammability

• NFPA 258 for Smoke Density

Silhouette Shallow Double Bowl

SEE REVERSE SIDE FOR ROUGHING-IN DIMENSIONS

•

When installed so top of sink is 876mm (34-1/2") from finished floor.

MEETS THE AMERICANS WITH DISABILITIES ACT GUIDELINES AND

ANSI A117.1 ACCESSIBLE AND USEABLE BUILDINGS AND

FACILITIES - CHECK LOCAL CODES.

BARRIER FREE

To Be Specied:

❏ Color:

❏ Faucet*:

❏ Faucet Finish:

❏ Basket Strainer: 4331.013

❏ Soap Dispenser: 4503.115, Color:

❏ Traps:

Optional Accessories:

❏ Large Wood Cutting Board: 9000.250

❏ Small Wood Cutting Board: 9000.185

❏ Colander for Cutting Board: 8102.100, Color:

❏ Large Colander: 8103.100, Color:

❏ Web Cover: 8106.100, Color:

❏ Bottom Sink Rack (Left): 7405.100, Color:

❏ Bottom Sink Rack (Right): 7406.100, Color:

G32

NOTES:

COUNTERTOP CUTOUT 527 X 806mm WITH 25mm

(20-3/4 X 31-3/4 WITH 1) RADIUS AT CORNERS.

SUPPLIES NOT INCLUDED AND MUST BE ORDERED SEPARATELY.

PROVIDE SUITABLE REINFORCEMENT FOR ALL WALL AND

COUNTERTOP SUPPORTS.

NOTES:

TEMPLATE PROVIDED WITH MOUNTING KIT 791326-100 FOR

UNDERCOUNTER FAUCET DECK CUTOUT VARIATIONS.

SUPPLIES NOT INCLUDED AND MUST BE ORDERED SEPARATELY.

PROVIDE SUITABLE REINFORCEMENT FOR ALL WALL AND

COUNTERTOP SUPPORTS.

IMPORTANT: Dimensions of xtures are nominal and may vary within the

range of tolerances established by ASME Standard A112.19.4

These measurements are subject to change or cancellation. No responsibility

is assumed for use of superseded or voided leaet.

7163.804

4 HOLE

7163.805

5 HOLE

7163.001

CHO

C/L

FINISHED WALL

OR SPLASHBACK

1-1/2" O.D.

TAILPIECE

FINISHED FLOOR

COUNTERTOP

(BY OTHERS)

SEALING

COMPOUND

*CUTOUT NOTE

1/2"

(13mm)

5-3/4"

(146mm)

5-1/2"

(140mm)

16-1/2"

(419mm)

33"

(838mm)

3-1/2"

(89mm)

DIA.

1-1/2" (38mm)

RAD. TYP.

7-7/8"

(200mm)

8-5/8"

(219mm)

7-7/8"

(200mm)

10-1/8"

(257mm)

22"

(559mm)

34"

(864mm)

2-1/8"

(54mm)

1-1/2" (38mm)

DIA. HOLES TYP.

4" (102mm)

(102mm)

4"(102mm)

2" (51mm)

OPTIONAL

7163.804

4 HOLE

7163.805

5 HOLE

7163.001

CHO

C/L

FINISHED WALL

OR SPLASHBACK

FINISHED FLOOR

COUNTERTOP

(BY OTHERS)

SEALING

COMPOUND

*CUTOUT NOTE

DETAI L O F MOU NTI NG CL IP

(KIT No. 79100 2-1 00)

BRASS

INSERT

3/4"

(19mm)

MIN.

REFER TO IN STRUC TIO NS

PROVIDED WI TH KI T F OR

ADDITION AL INFOR MAT ION

CLIP

MACH.

SCREW

SINK

2-1/8"

(54mm)

1-1/2" (38mm)

DIA. HOLES TYP.

4" (102mm)

(102mm)

4"(102mm)

2" (51mm)

OPTIONAL

16-1/2"

(419mm)

33"

(838mm)

36"

(914mm)

5-3/4"

(146mm)

(152mm)

7-7/8"

(200mm)

10-1/8"

(257mm)

22"

(559mm)

3-1/2"

(89mm)

DIA.

1-1/2" (38mm)

RAD. TYP.

7-7/8"

(200mm)

8-5/8"

(219mm)

1-1/2" O.D.

TAILPIECE

SILHOUETTE™ 33"

SHALLOW DOUBLE BOWL SINK

AMERICAST

Revised 2/08

Undercounter Mount

7163. Series

American Standard 7163.804 User manual

Brand: American Standard

Model: 7163.804

Type: User manual

This manual is also suitable for

Download PDF

report

American Standard 7163.804 User manual

This manual is also suitable for

American Standard 7163.804 User manual

Related papers

Other documents