American Standard 7145.805 User manual

Brand: American Standard

Model: 7145.805

Type: User manual

This manual is also suitable for

G27

Revised 2/08

SILHOUETTE™ 33" DOUBLE BOWL

KITCHEN SINK

• Americast

brand engineered material

• Dual level double bowl design

• Titanium enamel - heat resistant up to 1000°

• Acid-resisting glossy porcelain nish

• Top mount or undercounter installation

• Silicone sealant supplied

• Available in 1, 3, 4, or 5 faucet hole

conguration

• Customized hole punchings available

(see page G56)

Top Mount/Undercounter:

❏ 7145.001 Center hole only

❏ 7145.803 3 hole

❏ 7145.804 4 hole

❏ 7145.805 5 hole

Undercounter Installation Order:

❏ 791326-100 Mounting Kit (consists of

cut-out templates and mounting clips)

Nominal Dimensions:

838 x 559 x 241mm

(33" x 22" x 9-1/2")

Bowl sizes:

Right Hand: 359mm (14-1/8") wide

413mm (16-1/4") front to back

229mm (9") deep

Left Hand: 359mm (14-1/8") wide

476mm (18-3/4") front to back

229mm (9") deep

Compliance Certications -

Meets or Exceeds the Following Specications:

• ASME A112.19.4M for Americast Plumbing Fixtures

• ASTM E162 for Flammability

• NFPA 258 for Smoke Density

SILHOUETTE™ 33"

DOUBLE BOWL SINK

AMERICAST

Top Mount Installation

(faucet & soap dispenser not included)

Undercounter Mount Installation

(faucet not included)

SEE REVERSE SIDE FOR ROUGHING-IN DIMENSIONS

* See faucet section for available models

To Be Specied:

❏ Color:

❏ Faucet*:

❏ Faucet Finish:

❏ Basket Strainer: 4331.013

❏ Soap Dispenser: 4503.115, (specify color):

❏ Traps:

Optional Accessories:

❏ Large Wood Cutting Board: 9000.250

❏ Small Wood Cutting Board: 9000.185

❏ Colander for Cutting Board: 8102.100, Color:

❏ Large Colander: 8103.100, Color:

❏ Web Cover: 8106.100, Color:

❏ Bottom Sink Rack (Left): 7405.100, Color:

❏ Bottom Sink Rack (Right): 7406.100, Color:

G28

7145.803/804/805 Top Mount

Undercounter Mount

NOTES:

TEMPLATE PROVIDED WITH MOUNTING KIT 791326-100 FOR

EXPOSED FAUCET DECK OR UNDERCOUNTER FAUCET DECK

COUNTERTOP CUTOUT VARIATIONS.

FITTINGS AND UNDERCOUNTER MOUNTING KIT NOT INCLUDED

AND MUST BE ORDERED SEPARATELY.

PROVIDE SUITABLE REINFORCEMENT FOR ALL WALL AND

COUNTERTOP SUPPORTS.

IMPORTANT: Dimensions of xtures are nominal and may vary within the

range of tolerances established by ASME Standard A112.19.4

These measurements are subject to change or cancellation. No responsibility

is assumed for use of superseded or voided leaet.

NOTES:

TOP MOUNT (7145.803/4/5): COUNTERTOP CUTOUT

806 X 527mm WITH 25mm RADIUS (31-3/4 X 20-3/4 WITH 1" RAD.)

AT CORNERS.

FITTINGS NOT INCLUDED AND MUST BE ORDERED SEPARATELY.

PROVIDE SUITABLE REINFORCEMENT FOR ALL WALL AND

COUNTERTOP SUPPORTS.

IMPORTANT: Dimensions of xtures are nominal and may vary within the

range of tolerances established by ASME Standard A112.19.4

These measurements are subject to change or cancellation. No responsibility

is assumed for use of superseded or voided leaet.

7145.804

4 HOLE

7145.805

5 HOLE

C/L

FINISHED WALL

OR SPLASHBACK

1-1/2" O.D.

TAILPIECE

FINISHED

FLOOR

COUNTERTOP

(BY OTHERS)

SEALING

COMPOUND

*CUTOUT NOTE

9-1/8"

(232mm)

1/2"

(13mm)

5-3/4"

(146mm)

22"

(559mm)

36" (914mm)

SUGGESTED

16-1/2"

(419mm)

33"

(838mm)

3-1/2"

(89mm)

DIA.

1-1/2" (38mm)

RAD. TYP.

2-1/8"

(54mm)

1-1/2" (38mm)

DIA. HOLES TYP.

4" (102mm)

2" (51mm)

OPTIONAL

7-7/8"

(200mm)

8-5/8"

(219mm)

7-7/8"

(200mm)

10-1/8"

(257mm)

7145.804

4 HOLE

7145.805

5 HOLE

C/L

FINISHED WALL

OR SPLASHBACK

FINISHED

FLOOR

COUNTERTOP

(BY OTHERS)

SEALING

COMPOUND

CUTOUT

NOTE

MOUNTING CLIP

(SEE DETAIL)

DETAIL OF MOUNTING C LIP

(KIT No.7 91002-100)

BRASS

INSERT

3/4

(19mm)

MIN.

REFER T O INSTRUC TIONS

PROVIDE D WITH KI T FOR

ADDITIO NAL INFOR MATION

CLIP

MACH.

SCREW

SINK

1-1/2" O.D.

TAILPIECE

36" (914mm)

SUGGESTED

16-1/2"

(419mm)

33"

(838mm)

7-7/8"

(200mm)

10-1/8"

(257mm)

9-1/2"

(241mm)

5-3/4

(146mm)

3-1/2"

(89mm)

DIA.

1-1/2" (38mm)

RAD. TYP.

4" (102mm)

2" (51mm)

OPTIONAL

7-7/8"

(200mm)

8-5/8"

(219mm)

22"

(559mm)

2-1/8"

(54mm)

1-1/2" (38mm)

DIA. HOLES TYP.

4" (102mm)

SILHOUETTE™ 33"

DOUBLE BOWL SINK

AMERICAST

Revised 2/08

American Standard 7145.805 User manual

Brand: American Standard

Model: 7145.805

Type: User manual

This manual is also suitable for

Download PDF

report

American Standard 7145.805 User manual

This manual is also suitable for

American Standard 7145.805 User manual

Related papers

Other documents