American Standard 38 User manual

Brand: American Standard

Model: 38

Type: User manual

This manual is also suitable for

G19

Revised 2/08

SILHOUETTE™ 38" DUAL LEVEL KITCHEN SINK

• Americast

brand engineered material

• Dual level double bowl design

• Titanium enamel - heat resistant up to 1000°

• Acid-resisting glossy porcelain nish

• Top mount or undercounter installation

• Fits most standard 36" cabinet bases

• Silicone sealant supplied

• Available in 1, 3, 4, or 5 faucet hole

conguration

• Customized hole punchings available

(see page G56)

Top Mount/Undercounter:

❏ 7196.001 Center hole only

❏ 7196.803 3 hole

❏ 7196.804 4 hole

❏ 7196.805 5 hole

Undercounter Installation Order:

❏ 791001-100 Mounting Kit (consists of

cut-out templates and mounting clips)

Nominal Dimensions:

965 x 559 x 241mm

(38" x 22" x 9-1/2")

Bowl sizes:

Right Hand: 318mm (12-1/2") wide

413mm (16-1/4") front to back

178mm (7") deep

Left Hand: 527mm (20-3/4") wide

476mm (18-3/4") front to back

229mm (9") deep

Compliance Certications -

Meets or Exceeds the Following Specications:

• ASME A112.19.4M for Americast Plumbing Fixtures

• ASTM E162 for Flammability

• NFPA 258 for Smoke Density

* See faucet section for available models

To Be Specied:

❏ Color:

❏ Faucet*:

❏ Faucet Finish:

❏ Basket Strainer: 4331.013

❏ Soap Dispenser: 4503.115, (specify color):

❏ Traps:

Optional Accessories:

❏ Large Wood Cutting Board: 9000.250

❏ Small Wood Cutting Board: 9000.185

❏ Colander for Cutting Board: 8102.100, Color:

❏ Large Colander: 8103.100, Color:

❏ Web Cover: 8106.100, Color:

❏ Bottom Sink Rack (Left): 7407.100, Color:

SILHOUETTE™ 38"

DUAL LEVEL SINK

AMERICAST

Shown here as a Top Mount (faucet not included)

SEE REVERSE SIDE FOR ROUGHING-IN DIMENSIONS

G20

7196.803/804/805 Top Mount

Undercounter Mount

NOTES:

TEMPLATE PROVIDED WITH MOUNTING KIT 791001-100 FOR

EXPOSED FAUCET DECK OR UNDERCOUNTER FAUCET DECK

COUNTERTOP CUTOUT VARIATIONS.

FITTINGS NOT INCLUDED AND MUST BE ORDERED SEPARATELY.

PROVIDE SUITABLE REINFORCEMENT FOR ALL WALL AND

COUNTERTOP SUPPORTS.

IMPORTANT: Dimensions of xtures are nominal and may vary within the

range of tolerances established by ASME Standard A112.19.4

These measurements are subject to change or cancellation. No responsibility

is assumed for use of superseded or voided leaet.

NOTES:

COUNTERTOP CUTOUT 527mm x 933mm x 25mm RADIUS

(20-3/4 X 36-3/4 WITH 1" RADIUS) AT CORNERS.

FITTINGS NOT INCLUDED AND MUST BE ORDERED SEPARATELY.

PROVIDE SUITABLE REINFORCEMENT FOR ALL WALL AND

COUNTERTOP SUPPORTS.

IMPORTANT: Dimensions of xtures are nominal and may vary within the

range of tolerances established by ASME Standard A112.19.4

These measurements are subject to change or cancellation. No responsibility

is assumed for use of superseded or voided leaet.

3-1/2"

(89mm)

DIA.

2-1/8"

(54mm)

2"(51mm)

OPTIONAL

FINISHED WALL

OR SPLASHBACK

7-7/8"

(200mm)

8-1/8"

(206mm)

1-1/2" (38mm) DIA.

HOLES TYP.

C/L

3/16"

(5mm)

12-1/4"

(311mm)

11-1/8"

(283mm)

19"

(483mm)

38"

(965mm)

9-1/8"

(232mm)

5-3/4"

(146mm)

SEALING

COMPOUND

7-1/8"

(181mm)

36" (914mm)

SUGGESTED

FINISHED

FLOOR

COUNTERTOP

(BY OTHERS)

22"

(559mm)

*CUTOUT NOTE

7196.804

4 HOLE

7196.805

5 HOLE

1-1/2"

(38mm)

RAD.TYP.

1-1/2 O.D. TAILPIECE

5-3/4"

(146mm)

4"(102mm)

4" (102mm)4" (102mm) 4" (102mm)

1/2"

(13mm)

3/16"

(5mm)

4"(102 mm)

4"(102mm)4"(102mm) 4"(102mm)

2" (51mm) OPTIONAL

FINISHED WALL

OR SPLASHBACK

7-7/8"

(200mm)

8-1/8"

(206mm)

1-1/2"

(38mm) DIA.

HOLES TYP.

C/L

SEALING

COMPOUND

FINISHED FLOOR

COUNTERTOP

(BY OTHERS)

CUTOUT

NOTE

7196.804

4 HOLE

7196.805

5 HOLE

1-1/2" O.D.

TAILPIECE

MOUNTING CLIP

(SEE DETAIL)

DETAI L OF MOUN TING CL IP

(KIT No .791001 -100)

BRASS INSERT

3/4

MIN.

REFER TO INSTRUCTIONS

PROVIDED WITH KIT FOR

ADDITIONAL INFORMATION

CLIP

MACH.

SCREW

SINK

3-1/2"

(89mm)

DIA.

2-1/8"

(54mm)

12-1/4"

(311mm)

11-3/16"

(284mm)

19"

(483mm)

38"

(965mm)

22"

(559mm)

1-1/2"

(38mm)

RAD.TYP.

5-3/4"

(146mm)

36" (914mm)

SUGGESTED

5-3/4"

(146mm)

9-1/2"

(241mm)

7-1/2"

(191mm)

SILHOUETTE™ 38"

DUAL LEVEL SINK

AMERICAST

Revised 2/08

American Standard 38 User manual

Brand: American Standard

Model: 38

Type: User manual

This manual is also suitable for

Download PDF

report

American Standard 38 User manual

This manual is also suitable for

American Standard 38 User manual

Related papers

Other documents