Mettler Toledo InPro42i Serie User manual

Page is loading ...

14 InPro 42XX (i) Series pH electrode

InPro 42XX (i) pH electrode © 04 / 16 Mettler-Toledo GmbH

52 005 365 Printed in Switzerland

1 Introduction ...................................................................15

2 Safetyinstructions ..........................................................15

3 Product description .........................................................15

4 Installation and commissioning .......................................16

5 Operation:Calibrationoftheelectrode

andpHtransmitter .........................................................16

6 Maintenance ..................................................................16

7 Removalofsourcesofmalfunction ..................................17

8 Disposal ........................................................................17

9 Guarantee ......................................................................17

10 Storage conditions ..........................................................17

Contents

en

InPro

42XX (i) Series

pH Electrode

Instruction Manual

InPro,ISMandXerolytareregisteredtrademarks

ofMettler-ToledoGmbHinSwitzerland,theUSA,

theEuropeanUnionandafurthervecountries.

en Instruction Manual

InPro 42XX (i) Series pH electrode 15

Printed in Switzerland 52 005 365

1 Introduction

TheMETTLERTOLEDOInPro

®

42XX(i)pH-singlerod

measuringcellisalowmaintenance,high-pressure

resistantpHelectrodewithasolidpolymerelectrolyte

(Xerolyt

®

 Extra) together with a silver ions barrier.

Thediaphragmisofanopenaperturetype,sothat

direct contact exists between the medium being

measuredandtheelectrolyte.

Please read through these operating instructions

carefully before commissioning, in order to ensure

trouble-freeuse.

2 Safety instructions

When cleaning or calibrating the electrode using

solutionscontainingacidsoralkalisbothprotective

spectaclesandprotectiveglovesshouldbeworn.

Donottouchtheelectrodeattheplug-incontacts,since

electrostaticdischargescandamagetheelectronics.

Werecommendthatyouonlyoperatetheelectrodein

combinationwithoriginalpartsfromMETTLERTOLEDO.

Operationandmaintenanceshouldbecarriedoutonly

by trained personnel and staff who have read and

understoodtheoperatinginstructions.

3 Product description

The inscription on each electrode contains the

followinginformation:

METTLER TOLEDO Manufactureroftheelectrode

InPro

®

42XX i / SG / yyy / zzz  Typedesignation;XX=shaft

material,membraneglass;

i=ISMDigital/SG=ancillary

electrode/yyy=rodlengthin

mm/zzz=typeoftemperature

sensor

combination pH Typeofelectrode

pH 0 … 14 pH measurement range

pH 1 … 14 (InPro 4281 i)

0…100°C(130°C) Temperaturerangefor

operation (sterilization)

Order No. 52 00X XXX Order number

SEV14ATEX0168X Identicationandnumber

ofcerticate

IECExSEV14.0025X Identicationandnumber

ofcerticate

IS/I,II,III/1/ABCDEFG/T6 FMtested

Seeinstructionmanual! Instruction(Observethe

operating instructions)

In addition each electrode is allocated a serial

numberontheredpartoftheplug-inheadtoenable

identication.

en

16 InPro 42XX (i) Series pH electrode

InPro 42XX (i) pH electrode © 04 / 16 Mettler-Toledo GmbH

52 005 365 Printed in Switzerland

4 Installation and commissioning

1. While unpacking check the electrode for

mechanicaldamage.Pleasereportanydamage

immediatelytoyourMETTLERTOLEDOsupplier.

2.Removetheprotectivecapandrinsetheelectrode

for a short time with deionized water. If the

electrodehasalreadybeenusedthesensitivepart

canbecleanedwithasofttoothbrushandamild

soapsolution,andthenrinsedforashorttimewith

deionizedwater.Afterrinsingtheelectrodeshould

onlybedabbed.AnyrubbingofthepHsensitive

glasscanincreasetheresponsetimeasaresult

ofelectrostaticchargeaccumulation.

3.Check the spacebehind thepHsensitive glass

forairbubblesandremoveanyairbubblesthat

maybepresentbyshakingtheelectrodeslightly

in a vertical direction.

4.Placetheelectrodeintothehousingasdescribed

intheinstructionsforthehousing.

5.ConnecttheelectrodeandthepHtransmitterwith

thecorrespondingcable(VP6,VP8,AK9).Observe

the connections scheme that accompanies

thecableorthetransmitter.

6. Intelligent ISM

®

sensorssuchasInPro426Xienable

“PlugandMeasure” andexpandeddiagnostics.

Forinstallation,commissioningandoperationof

theISMsystempleaserefertoinstructionsforthe

transmitter, module and cable.

5 Operation: Calibration of the electrode

and pH transmitter

Before a calibration immerse the electrode for

10minutesinapH7.00orpH4.01buffersolution

whilst connected it to the transmitter. A 2-point

calibration is recommended, e.g. pH 7.00 and pH

4.01buffersolutions.Forfurtherdetailspleaseconsult

theoperatinginstructionsforthepHtransmitter.

6 Maintenance

1. After each working cycle the electrode tip and

diaphragm have to be carefully rinsed with

deionized water. Any remaning of the solution

beingmeasuredonthesepartsmustbeavoided

at all costs!

2. Iftheelectrodeisnotinuseithastobestoredwith

theelectrodetipandthediaphragmimmersedin

atankofelectrolyte(9823/3MKClorFriscolyt™

9848).).

en

InPro 42XX (i) Series pH electrode 17

Printed in Switzerland 52 005 365

3. Iftheelectrodeisstoredinitshousingtheadvices

described under Item 2 apply, although the

electrolytehastobeslightlymodiedforstorage

purposes (2 parts of buffer solution pH 9.2 to

10 parts of electrolyte) in order to avoid any

corrosionofthehousingparts.

4. If an electrode is inadvertently stored in a dry

condition for several days it must be rinsed

forseveralhoursinastandardstorageelectrolyte.

5. Theplug-inheadshouldoccasionallybechecked

forpossibletracesofmoisture.Ifnecessaryclean

itthoroughlywithdeionizedwateroralcoholand

thendryitoffcarefully.

7 Removal of sources of malfunction

Withasofttoothbrushandwateranyresiduescan

easilyberemovedfromtheelectrode.Mildwashing

agents can also be used.

8 Disposal

Itistheuser’sresponsibilitytodisposeofthesensor

inaprofessional manner. The sensor can contain

electroniccomponentsthatrequiredisposalsuchthat

nopersonsortheenvironmentareendangered.

9 Guarantee

Onmanufacturingdefects12monthsafterdelivery.

10 Storage conditions

Werecommendthattheelectrodesarestoredatroom

temperature.

en

Page is loading ...

74 InPro 42XX (i) Series pH electrode

52 005 365 Printed in Switzerland

–

Notes

InPro 42XX (i) Series pH electrode 75

Printed in Switzerland 52 005 365

–

Notes

Brazil Mettler-Toledo Ind. e Com. Ltda.

 AvenidaTamboré,418–Tamboré,

 BR-06460-000Barueri/SP,Brazil

 Phone+551141667400

 e-mailmettler@mettler.com.br;service@mettler.com.br

France Mettler-Toledo Analyse Industrielle S.A.S.

 30,Bld.deDouaumont,FR-75017Paris,France

 Phone+33147370600

 e-mailmtpro-f@mt.com

Germany Mettler-Toledo GmbH

 Prozeßanalytik,Ockerweg3,DE-35396Gießen

 Phone+49641507-444

 e-mailprozess@mt.com

Switzerland Mettler-Toledo (Schweiz) GmbH

 ImLangacher,CH-8606Greifensee

 Phone+41449444760

 e-mailProSupport.ch@mt.com

United States METTLER TOLEDO

 ProcessAnalytics

 900MiddlesexTurnpike,Bld.8,Billerica,MA01821,USA

 Phone+17813018800

 Freephone+18003528763(onlyUSA)

 e-mailmtprous@mt.com

FormoreaddressesofMETTLERTOLEDOMarketOrganizationspleasegoto:

www.mt.com/pro-MOs

Mettler-ToledoGmbH,ProcessAnalytics,ImHackacker15,CH-8902Urdorf

Phone+41447296211,Fax+41447296636

Subjecttotechnicalchanges

PrintedinSwitzerland.52005365

www.mt.com/pro

Addresses|Impressum

Mettler Toledo InPro42i Serie User manual

This manual is also suitable for

Mettler Toledo InPro42i Serie User manual

in other languages

Related papers

Other documents