Mettler Toledo pH electrodes InPro325Xi Operating instructions

  • Hello! I am an AI chatbot trained to assist you with the Mettler Toledo pH electrodes InPro325Xi Operating instructions. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
8 InPro325X(i)pHElectrodes
© 03 / 18 Mettler-Toledo GmbH InPro 325X {i) pH Electrodes
Printed in Switzerland 52 002 631
InPro 325X (i)
pH Electrodes
Instruction manual
1 Introduction
TheMETTLERTOLEDOInPro
®
325X(i)pHsinglerodmeasuringcell
is a low maintenance, autoclavable and pressure resistant pH
electrodewithapre-pressurisedliquidelectrolyteandareference
electrolytetogetherwithasilverionsbarrier.Pleasereadthrough
these operating instructions carefully before commissioning, in
order to ensure trouble-free use. We recommend that you only
operate the electrode in conjunction with original parts from
METTLERTOLEDO.Operationandmaintenanceshouldbecarried
out only by trained personnel and staff who have read and
understoodtheoperatinginstructions.
2 Safetyinstructions
Whencleaningorcalibratingtheelectrodeusingsolutionscontaining
acids or alkalis both protective spectacles and protective gloves
shouldbeworn.Donottouchtheelectrodeattheplug-incontacts,
sinceelectrostaticdischargescandamagetheelectronics.
3 Product description
Theinscriptiononeachelectrodecontainsthefollowinginformation:
METTLER TOLEDO Manufacturerofthe
electrode
InPro 325X
i / SG / yyy / zzz Typedesignation:
X = membrane glass
i =ISMDigital/
SG = auxillaryelectrode/
yyy=rodlengthinmm/
zzz= typeoftemperature
sensor
combination pH Type
ofelectrode
pH
0…14(InPro3250)
pH0…12(InPro3253)
pH1…11(InPro3251,InPro3252)
pH-measurementrange
•0…100°C(upto140°C
InPro3250,InPro3253)
•–25…80°C(InPro3251)
•0…80°C(InPro3252)
Temperature
rangefor
operation (for sterilisation)
OrderNo.5200XXXX Ordernumber
SEV14ATEX0168X
Identicationandnumber
ofcerticate
IECExSEV14.0025X
Identicationandnumber
ofcerticate
IS
/I,II,III/1/ABCDEFG/T6 FMtested
See instruction manual Note
Inadditioneachelectrodeisprovidedwithaserialnumberonthe
redpartoftheplug-inheadinordertoenableidentication.
This product complies with the ATEX guideline 94/9/EC. The
completedeclarationcanbedownloadedunderwww.mt.com/pro.
4 Installationandcommissioning
1.While unpackingcheckthe electrodefor mechanical damage.
PleasereportanydamageimmediatelytoyourMETTLERTOLEDO
supplier.
2.Remove the protectivecap and rinse the electrodefora short
timewithdeionisedwater.Carefullyremovethesiliconprotection
fromthediaphragmwiththeaidoftheknifesupplied(cf.green
instruction images on the packaging). If the electrode has
already been used the sensitive part can be cleaned if
necessarywithasofttoothbrushandamildsoapsolution,and
thenrinsedforashorttimewithdeionisedwater.Afterrinsing
the electrode should only be dabbed. Any rubbing of the
pH-sensitiveglasscanincreasetheresponsetime asaresult
ofelectrostaticchargeaccumulation.
3.CheckthespacebehindthepHsensitiveglassforairbubblesand
remove any air bubbles that may be present by shaking the
electrodelightlyinaverticaldirection.
en
en Instruction Manual
InPro325X(i)pHElectrodes 9
InPro 325X (i) pH Electrodes © 03 / 18 Mettler-Toledo GmbH
52 002 631 Printed in Switzerland
4.Place the electrode into the armature as described in the
instructionsforthearmature.
5.ConnecttheelectrodeandthepHtransmitterwiththecorresponding
cable(VP6,VP8,AK9).Observe the connectionsschemethat
accompaniesthecableorthetransmitter.
6.IntelligentISM
®
sensorssuchasInPro325Xienable«plugand
measure»andextendeddiagnostics.Operationoftheelectrodes
intheISMmoderequirestheM700transmitteraswellasanISM
pH-module (2700i X). For installation, commissioning and
operationoftheISMsystempleaseobservetheinstructionsfor
thetransmitter,moduleandcable.
5 Operation:
Calibration
oftheelectrodeandpHtransmitter
Beforeacalibrationimmersetheelectrodefor10minutesinapH
7.00orpH4.01buffersolutionwhilstconnectingittothetransmitter.
A2-pointcalibrationisrecommended,e.g.pH7.00andpH4.01
buffer solutions. Forfurther details please consult the operating
instructionsforthepHtransmitter.
6 Maintenance
1.Aftereachworkingcycletheelectrodetipanddiaphragm(s)are
to be carefully rinsed with deionised water.Any drying out of
residuesfromthesolutionbeingmeasuredonthesepartsmust
be avoided at all costs!
2.Iftheelectrodeisnotinuseitisstoredwiththeelectrodetipand
thediaphragmimmersedinatankofelectrolyte(9823/3MKCl
or9848Friscolyt™).
3.If the electrode is stored in its armature the rules described
underItem2apply,althoughtheelectrolytehastobeslightly
modiedforstoragepurposes(2partsofbuffersolutionpH9.2
to 10 parts of electrolyte) in order to avoid any corrosion of
thearmatureparts.
4.If an electrode is inadvertently stored in a dry condition for
severaldaysitmustberinsedforseveralhoursinastandard
storageelectrolyte.
5.Theplug-inheadshouldoccasionallybecheckedforpossible
tracesofmoisture.Ifnecessarycleanitthoroughlywithdeionised
wateroralcoholandthendryitoffcarefully.
7 Removalofsourcesofmalfunction
Withasofttoothbrushandwateranyresiduescaneasilyberemoved
fromtheelectrode.Mildwashingagentscanalsobeused.Protein
contaminationsonthediaphragmcanbemostlikelyremovedwith
thecleaningsolution(orderno.51340070).
a
Warning:Solutionscontaininghydrouoricaciddamagethe
pHsensitivepartoftheelectrode.
8 Environmental protection
Waste electricalproductsshouldnot bedisposed of
withhouseholdwaste.Pleaserecyclewherefacilities
exist. Check with your Local Authority or retailer for
recyclingadvice.
9 Warranty
Onmanufacturingdefects12monthsafterdelivery.
10 Storageconditions
Werecommendthattheelectrodesarestoredatroomtemperature.
InPro,ISMandFriscolytaretrademarksoftheMETTLERTOLEDO
Group.
en
InPro325X(i)pHElectrodes 39
InPro 325X (i) pH Electrodes © 03 / 18 Mettler-Toledo GmbH
52 002 631 Printed in Switzerland
Notes
Brazil Mettler-Toledo Ind. e Com. Ltda.
AvenidaTamboré,418–Tamboré,
BR-06460-000Barueri/SP,Brazil
Phone+551141667400
e-mailmtbr@mt.com
France Mettler-Toledo Analyse Industrielle S.A.S.
30,Bld.deDouaumont,FR-75017Paris,France
Phone+33147370600
e-mailmtpro-f@mt.com
Germany Mettler-Toledo GmbH
Prozeßanalytik,Ockerweg3,DE-35396Gießen
Phone+49641507-444
e-mailprozess@mt.com
Switzerland Mettler-Toledo(Schweiz)GmbH
ImLangacher,CH-8606Greifensee
Phone+41449444747
e-mailProSupport.ch@mt.com
United States METTLER TOLEDO
ProcessAnalytics
900MiddlesexTurnpike,Bld.8,Billerica,MA01821,USA
Phone+17813018800
Freephone+18003528763(onlyUSA)
e-mailmtprous@mt.com
FormoreaddressesofMETTLERTOLEDOMarketOrganizationspleasegoto:
www.mt.com/pro-MOs
Mettler-ToledoGmbH,ProcessAnalytics,ImHackacker15,CH-8902Urdorf
Phone
+41447296211,Fax+41447296636
Subjecttotechnicalchanges
03/2018©METTLERTOLEDO.Allrightsreserved
Rev.B.PrintedinSwitzerland.52000631
www.mt.com/pro
Addresses|Impressum
1258
/