Workrite Ergonomics Bluetooth Dongle Upgrade Kit Installation guide

Brand
Workrite Ergonomics
Model
Bluetooth Dongle Upgrade Kit
Category
Signal cables
Type
Installation guide

This manual is also suitable for

Workrite Ergonomics | 800.959.9675 www.workriteergo.com 1 of 4
Assembly & Installation Instructions:
Bluetooth & Workrite App Upgrade Kit
for Sierra HX and Fundamentals FDEX & FDLX
BT-UPGRADE-KIT
Cable, Splitter, & Dongle Assembly
Install the 12" RJ45 Cable (F) into the single port of the RJ45 Splitter (C).
Parts Included
F 12" RJ45 Extension Cable
Qty: 1
D Bluetooth Dongle
Qty: 1A #8 × 1" Phillips
Pan Head Screw
Qty: 2
B #8 × ⅝" Phillips
Pan Head Screw
Qty: 1
C RJ45 Splitter
Qty: 1
E P-Loop
Qty: 1
1
a
1a
F
C
2 of 4 Workrite Ergonomics | 800.959.9675 www.workriteergo.com
For Fundamentals 2-Leg
Connect Splitter Assembly for bases with Control Box
If there is an open switch port on the control box, plug
the Bluetooth Dongle (D) directly into the control box.
On the Fundamentals 2-leg table, un-plug the switch
cable from the master leg.
If both switch ports of the control box are in
use, un-plug the switch cable from the control
box and plug in the Splitter Assembly into the
control box.
Plug the Splitter Assembly into the master leg.
Install the Bluetooth Dongle (D) into
one of the two ports of the RJ45
Splitter (C).
Install the Bluetooth Dongle (D) into
one of the two ports of the RJ45
Splitter (C).
2
2
2b
4a
4b
4c
2b
2c
2c
a
a
b
b
D
D
F
c
c
C
C
MEMS Dongle
3 of 4 Workrite Ergonomics | 800.959.9675 www.workriteergo.com
Plug in hand switch
Re-route the hand switch cable to plug into the Splitter (C) and
plug it into the open RJ45 port
NOTE : It may be necessary to remove and replace
the P-Loops on the hand switch cable to be sure the
cable is properly managed and does not hang down
from the worksurface.
NOTE: Be sure the splitter is mounted securely.
Improper attachment will cause the MEMS anti-col-
lision to fail if the splitter is not tightly secured to the
desktop.
Attach the Splitter to the desktop
Place the splitter against the desktop and install two (2) #8 x 1"
Phillips Pan Head Screws (A) and tighten securely.
Place the P-Loop (E) onto the 12" RJ45 Cable (F).
Attach the P-Loop to the top with one (1) #8 x ⅝"
Phillips Head Screw (B).
4
a
Switch Cable
Switch Cable
4a
4a
3
a
b
c
A
3a
3b
3c
B
E
F
C
4 of 4 Workrite Ergonomics | 800.959.9675 www.workriteergo.com
1500506 Rev A
THE WORKRITE APP
• Go to https://apps.apple.com/us/app/workrite-bluetooth-pro-switch/id1483434040
to download the Workrite App on your IOS, or search “Workrite Bluetooth Pro Switch”
in the App Store
• Go to https://play.google.com/store/apps/details?id=com.workriteergo.btproswitch
to download the Workrite App on your Android device, or search “Workrite Bluetooth
Pro Switch” in the Google Play Store
• Follow the prompts in the app to set up your table with blue tooth paring and the other features that are enabled
by the app
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Workrite Ergonomics Bluetooth Dongle Upgrade Kit Installation guide

Brand
Workrite Ergonomics
Model
Bluetooth Dongle Upgrade Kit
Category
Signal cables
Type
Installation guide
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents