Assa Abloy ES110-1M Installation guide

Brand: Assa Abloy

Model: ES110-1M

Type: Installation guide

This manual is also suitable for

ES100 Series

ES100/ES110 - 121 - 0316

To change electric strike’s mode of lock operation, remove brass screw from

top of strike body.

Invert strike and carefully release the small spring and 3 locking pins

(2 x Short pin, 1 x Long pin).

Re-insert pins in in the manner shown for the desired mode of lock

operation (Power to Open / fail Secure): see Fig. 1;

(Power to Lock / fail safe): see Fig. 2, followed by replacing the spring.

Screw in the brass screw to strike body. This will secure the spring and

locking pins.

ES100 /ES110 SERIES ELECTRIC STRIKE

INSTALLATION INSTRUCTIONS

Hole ‘B’ for

timber frame

Hole ‘A’ for

metal frame

Small End of

spring

Short Pins

Long Pin

Short Pins

Long Pin

• Peel backing off adhesive template and centrally locate in the

marked position, lining up both the mark for the door latch front

face (Line 1) and the centre mark of the latch (Line 2).

• For the metal door drill two Ø5mm holes (A) 24mm above and

below the “X” mark on the template, for a timber door drill

two Ø3mm holes (B).

• Ensure secondary bolt is not within the strike cavity.

• To enable the Electric strike to be located in the door frame, first

mark the position of the Door Latch front face on the door frame

with the door in the closed position, (”X”mm).

• Mark where centre of latch meets door frame:

- For new installations, mark frame where front of latch touches

the door frame at the midpoint of the latch bolt.

- For retrofit installations, remove existing strike plate and ensure

the latch fits into and is centred in existing hole.

CHANGING MODE OF LOCK OPERATION

MORTICING REBATE

POSITIONING OF STRIKE

MARKING OF STRIKE POSITION

• Using the template as a guide, mortice out the door frame to the

required size.

• Countersink holes in metal frame to accept screws.

Door

Frame

Door

Frame

Latch

Mark Door latch

front face on frame

(Line 1).

“X”

Mark centre of Door

latch on frame

(Line 2).

100A series - 17mm

110A series - 20mm

100B series - 17mm

110B series - 20mm

100B series - 17mm

110B series - 20mm

100A series - 17mm

110A series - 20mm

Power to Open

(Fail-Secure)

Fig 1

Power to Lock

(Fail-Safe)

Fig 2

Keeper

edge

The installation of a latch guard is recommended on outward opening

external doors.

• For metal door frames fit door mounting brackets.

• Once door frame preparation is compelte, temporarily fit strike into

door frame to check for interference. Check that the door closes

smoothly and that the latch extends past the strike keeper.

• When strike operates correctly with latch, remove strike from

mortice and connect wiring.

• Refit strike and secure, making sure no wires are being crushed.

• Check both mechanical and electronic operation works correctly.

Deadlatching

TUBULAR LATCH OPERATION

To ensure deadlatching, ensure

that the deadlatching pin is

depresed by the edge of the

keeper when the door is closed.

An ASSA ABLOY Group brand

ELECTRICAL SPECIFICATION

CHECKING FUNCTIONASSEMBLING STRIKE

CAUTION! - Incorrect supply voltage may cause damage not covered by warranty.

Please check supply voltage with a suitable meter to ensure it is within ± 15% of the nominal

voltage shown above with the strike powered.

DO NOT OIL OR LUBRICATE

24V DC 125mA 12V DC 250mA

Blue Red

Black

White

Blue

Red

White

Black

•

• •

•

Blue and Black to Power Supply.

Red and White joined together.

Red and Black joined and to Power Supply.

Blue and White joined and to Power Supply.

•

15mm Extension Lip

P/No. 220110 - 502

25mm Extension Lip

P/No. 220110 - 503

50mm Extension Lip

P/No. 220110 - 504

Assa Abloy ES110-1M Installation guide

Brand: Assa Abloy

Model: ES110-1M

Type: Installation guide

This manual is also suitable for

ES100 Series

Download PDF

report

Assa Abloy ES110-1M Installation guide

This manual is also suitable for

Assa Abloy ES110-1M Installation guide

Related papers

Other documents