ENTRO A0500SSSM NEEWER Z1 Round Head Flash Speedlite For Canon Dslr Cameras User manual

Brand
ENTRO
Model
A0500SSSM NEEWER Z1 Round Head Flash Speedlite For Canon Dslr Cameras
Type
User manual
REVERSE BOLT HEAD FOR
HANDING
Determine lock handing from the
Handing of Door chart. Rotate bolt
head if required by removing Face
Plate to pull and rotate the bolt 180°
to suit the Latching direction.
A0500SSSM NARROW STILE MORTICE LOCK
Installation Instructions
www.entro.com.au
IMPORTANT:
Before drilling door, ensure correct handing is being installed
NOTE:
Case does not need to be opened at any time to change
function or handling of this lock NOTE: Ensure door furniture supplied match the correct hole dimensions being drilled.
HANDING OF DOOR
RIGHT-HAND DOOR
LOCKING STATUS
Locking bar must be UP (unlocked) to change
Both Side Lockable
(Warning! Not suitable
for Escape Doors)
Other Side Locking
(Right Hand Doors)
This Side Locking
(Left Hand Doors)
Rotate Anti-
Clockwise Only
LEFT-HAND DOOR
OUTSIDE DOOR
OPENING
IN
OUTSIDE DOOR
OPENING
IN
OUTSIDE DOOR
OPENING
OUT
OUTSIDE DOOR
OPENING
OUT
METAL DOOR PREPARATION
1. Determine the height of the lockset on the door
2. Cut out the mortice window 156mm x 25.5mm with
3mm radius corners
3. Place template in opening and drill 4.5mm holes,
countersink with 8mm dia at 90°
4. Drill other appropriate holes for the selected lockset.
Dimensions in the illustration suit a 30mm backset lock
5. Do not drill holes all the way through to avoid door
damage or incorrect installation
CHECK LOCK STATUS
Ensure that the locking bar is in the
unlocked position (UP). If position
needs to be changed to the unlock
position, use a small flat blade
screwdriver, to lever out plastic
cylinder hole plug (where fitted)
and lift locking bar using the
screwdriver.
LOCK FUNCTIONS
Depending on the locking function
required it can be set to any
vestibule or combination lock
status. To change the locking
function, use a small flat blade
screwdriver to rotate (Anti-
Clockwise Only) the locking wedge
to desired location. Refer to the
Locking Status label on the lock
body for further detail.
TURN ADAPTOR INSTALLATION
ENTRO turn adaptors are captive adaptors and must be installed correctly for
proper lock operation.
1. Determine handing for adaptor
2. Put lock into LOCKED STATUS
by moving locking bar in down
position.
3. Insert adaptor ensuring the
cam plate is engaged with the
locking bar.
4.
Insert retaining pin and test
operation, ensuring the
locking bar is operating up &
down with operation of cam
(Maximum ¼ turn left or right).
5.
Lock can now be left in UN-
LOCKED STATUS with lock bar
UP until installed on door.
1. DOOR PREPARATION
2. LOCK PREPARATION
A0500SSSM NARROW STILE MORTICE LOCK Installation Instructions
Detail "A"
Locking Status
Indicator
LOCKING BAR
"UP"
167
156
27.5
5.5
R3
25.5
Ø4.5mm hole
Ø8mm countersink x 90°
37 90
159
27.5
14
90
20
30
Detail "A"
A0500SSSM NARROW STILE MORTICE LOCK
Installation Instructions
A0500SSSM NARROW STILE MORTICE LOCK Installation Instructions www.entro.com.au
3. LOCK INSTALLATION
4. DOOR FURNITURE INSTALLATION
FIT LOCK
Insert Lock into door and
secure with 2 screws.
FIT FURNITURE
Rotate handle to the desired handing
as shown. Ensure furniture screws are
minimum 5mm and maximum 15mm
past the door face. Position furniture
plates and secure with mounting screws.
FIT MOUNTING STRIKE
1. Prepare doorjamb
cutout and fit Strike
Box to frame.
2. Fit Strike to Strike
Box and secure with
2 screws.
LOCKS WITH CYLINDERS
1.
screwdriver, lever out
Using a small flat
the cylinder hole plug,
where fitted. Insert
lock into door and
secure with 2 screws.
2. Secure cylinder with
retainer pin, ensuring
pin is flush with front
face or lock.
3. Install face plate and
secure with 2 screws.
LOCK WITHOUT CYLINDER
Install face plate and secure with 2 screws.
LOCKS WITH TURNSNIB
Mark and cut
the connecting
bar as shown.
The turnsnib
must be in
the vertical
position when
unlocked.
LOCKS FOR DOOR LEVERS WITH SPINDLES
Insert spindle/s into lock as required,
ensuring the
spindle spring
is attached to
the rear of the
spindle before
assembling.
5-15mm
86
70
28.5
45
Ø4.5mm hole
Ø8mm Countersink x 90°
TO SUIT STRIKE BOX
21
5mm
  • Page 1 1
  • Page 2 2

ENTRO A0500SSSM NEEWER Z1 Round Head Flash Speedlite For Canon Dslr Cameras User manual

Brand
ENTRO
Model
A0500SSSM NEEWER Z1 Round Head Flash Speedlite For Canon Dslr Cameras
Type
User manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents