Maxxima MRL-61125 Installation guide

Type
Installation guide

Maxxima MRL-61125 is a 6" LED retrofit kit designed to provide energy-efficient lighting with adjustable color temperature and night light mode. It features a compact design for easy installation in recessed housings and offers a variety of color temperatures ranging from 2700K to 5000K to suit different preferences and environments. Additionally, it includes a night light mode that can be activated by quickly switching the light on and off, making it ideal for low-light illumination.

Maxxima MRL-61125 is a 6" LED retrofit kit designed to provide energy-efficient lighting with adjustable color temperature and night light mode. It features a compact design for easy installation in recessed housings and offers a variety of color temperatures ranging from 2700K to 5000K to suit different preferences and environments. Additionally, it includes a night light mode that can be activated by quickly switching the light on and off, making it ideal for low-light illumination.

6” LED Retrofit-Kit With Night Light Installation Guide
MRL - 61125
www.maxximastyle.com
[email protected] 866-MAXXIMA (629-9462) www.maxximastyle.com 125 Cabot Court Hauppauge, NY 11788
3 YEAR WARRANTY
Maxxima extends a 3 year limited warranty to the original purchase that the products listed are free from defects in material and/or
workmanship only. Maxxima will replace any warrantied product to the original consumer/purchaser if the product fails because of defects
due to workmanship and/or materials within the limited warranty period. Limited warranty is not transferable and applies to the original
installation of the Maxxima product. This offer does not constitute in any way a product guarantee and Maxxima does not hereby assume
any obligation whatsoever beyond sending a free replacement product.
Risk of electric shock or fire - Disconnect power at the source
before installation.
If you are unsure about the installation or the maintenance
of the fixture, please consult an electrician.
Do not make or alter any holes in the wiring enclosure or
modify any electrical componentry.
• To prevent wiring damage or abrasion, do not expose wiring
to edges of sheet metal or other sharp objects.
CAUTIONS
The fixture must be wired in accordance with
the National Electric Code (N.E.C) standards and
any applicable local codes or ordinances.
• This fixture is not compatible with photo controls,
occupancy sensors, or timing devices.
• This fixture is designed for use with 120Vac, 50/60Hz only.
• The retrofit kit is accepted as a component of a luminaire
where the suitability of the combination shall be determined
by CSA or authorities having jurisdiction.
WARNINGS
Electrical Parameters:
Model
MRL-61125
Input
Voltage
120 VAC
Input
Frequency
60 Hz
Input
Current
120mA
Input
Wattage
11W
Figure 2
Figure 5
Figure 4
Figure 3
7.5”
2.5” 1.4”
2700K
3000K
3500K
4000K
5000K
Figure 1
1. Ensure the power has been turned off by switching the circuit breaker
to the off position or by removing the fuse from the fuse panel.
2. If replacing an existing fixture remove and disconnect the
existing fixture from the housing.
3. Select the desired color temperature by moving the selector switch shown
in figure 1.
4. Twist the E26 adapter into the housing as shown in figure 2.
5. Connect the orange connector to the E26 adapter as shown in figure 3.
6. Ensure the torsion springs are within the 6” housing and that the supply wires
will not get pinched. As seen in figure 4.
7. With the torsion springs in position push the fixture up until flush with
ceiling, as shown in figure 5.
8. Restore power and the light is now operational.
9. To turn on night light mode after switching the light on, switch the light
off then on again within a second. The night light will be on within a second.
10. MRL-61125 utilizes a memory feature such that the light(s) will remain in the
previously used mode (either normal light mode or night light mode). Once the
user switches the light(s) on, then off, then on quickly, the mode of the light(s)
will change. This would be night light mode if the light(s) were in normal mode,
or normal mode if the light(s) were in night light mode. The light(s) sense this
quick switching action, which allows the user to toggle in and out of night light mode. If this
quick switching action is not detected, then the light will remain in its current mode.
Product Dimensions:
INSTALLATION INSTRUCTIONS
  • Page 1 1

Maxxima MRL-61125 Installation guide

Type
Installation guide

Maxxima MRL-61125 is a 6" LED retrofit kit designed to provide energy-efficient lighting with adjustable color temperature and night light mode. It features a compact design for easy installation in recessed housings and offers a variety of color temperatures ranging from 2700K to 5000K to suit different preferences and environments. Additionally, it includes a night light mode that can be activated by quickly switching the light on and off, making it ideal for low-light illumination.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI