Maxxima MRL-61300NW-4 Installation guide

Brand
Maxxima
Model
MRL-61300NW-4
Type
Installation guide

Maxxima MRL-61300NW-4 is a LED retrofit kit designed for use in 5" or 6" recessed housings. It features an E26 socket adapter, torsion springs for easy installation, and a 5-year warranty. The kit is not compatible with photo controls, occupancy sensors, or timing devices. Approved dimmers include:

  • AH Lighting: SDM3/1000/WHITE, SDM/600/WHITE
  • Almond LUXDM600-12
  • GE: 18024
  • Leviton: IPI06-1LZ, IPI10-1LZ, IPL06, 603-6631-A, 6631-A, 6631-LA, 6672, 6683, 6683-10Z, 6683

Maxxima MRL-61300NW-4 is a LED retrofit kit designed for use in 5" or 6" recessed housings. It features an E26 socket adapter, torsion springs for easy installation, and a 5-year warranty. The kit is not compatible with photo controls, occupancy sensors, or timing devices. Approved dimmers include:

  • AH Lighting: SDM3/1000/WHITE, SDM/600/WHITE
  • Almond LUXDM600-12
  • GE: 18024
  • Leviton: IPI06-1LZ, IPI10-1LZ, IPL06, 603-6631-A, 6631-A, 6631-LA, 6672, 6683, 6683-10Z, 6683
Electrical parameters:
Installation Into Recessed Housing:
STEP1:
. Remove the existing diffuser,
bulb and trim as applicable.
STEP2: Screw E26 socket adapter into socket
in housing. (Figure 1)
Figure 1
STEP3: Squeeze the torsion springs together
and install into torsion spring brackets inside
the housing as shown. (Figure 2)
STEP4: Tuck all wires into the housing and
carefully p
(Figure
3
Figure2
5", 6" LED Retrofit-Kit Installation Instructions
ese instructions Type luminaires.
3, MRL-61300NW
2 3
Figure3
NOTE: Torsion springs are pre-installed for 6" housing compatibility. For use in 5" housing
move both springs to the upper position as shown on the other side.
2.
WARNING / ATTENTION
4.
5.
other
1.
If luminaire (fixture) is to be switched from a wall switch, make sure black power supply wire
is connected to the switch. DO NOT connect the white supply wire to the switch.
2. Make sure no bare wires are exposed outside the wire nut connectors.
1.
. Supply conductors (power wires) connecting to the fixture must be rated 90°C.
If uncertain consult an electrician.
3.
CAUTIONS
1. For your safety read and understand instructions completely before starting installation.
3.
2.
Before attempting Installation, check your local electric code, as it sets wiring standards for
your locality.
NOTES
qualified electrician.
during kits installation.
6. This lamp is not intended for use with emergency exit fixtures or emergency lights.
4. This lamp is not compatible with photo controls, occupancy sensors, or timing devices.
+RXVLQJ'LPHQVLRQV
6.5
7.3
www.maxximastyle.com
Luminous Intensity Distribution Diagram
Five Year Warranty:
Maxxima extends a 5 year limited warranty to the original purchase that the products listed are free from defects in material and/or
workmanship only. Maxxima will replace any warranteed product to the original consumer/purchaser if the product fails because of defects
due to workmanship and/or materials within the limited warranty period.
Limited warranty is not transferable and applies to the original
installation of the Maxxima product. This offer does not constitute in any way a product guarantee and Maxxima does not hereby
assume any obilgation whatsoever beyond sending a free replacement product.
Approved Dimmers
AH Lighting: SDM3/1000/WHITE, SDM/600/WHITE
Almond LUXDM600-12
GE: 18024
Leviton: IPI06-1LZ, IPI10-1LZ, IPL06, 603-6631-A, 6631-A,
6631-LA, 6672, 6683, 6683-10Z, 6683-10Z
Lutron: S-603PH-WH
3.6"
NOTE: Torsion springs are pre-installed for 6" housing compatibility. For use in 5" housing
move both springs to the upper position. To do this, fold torsion springs down at center with
flat head screwdriver as shown below to unlock from lower position then slide out. Then
slide that spring into upper position and fold spring up at center to lock in place.
Torsion Springs in 6" Position
7.5"
Torsion Springs in 5" Position
Torsion Spring Relocation
Removal of Torsion Spring from 6" Position
  • Page 1 1
  • Page 2 2

Maxxima MRL-61300NW-4 Installation guide

Brand
Maxxima
Model
MRL-61300NW-4
Type
Installation guide

Maxxima MRL-61300NW-4 is a LED retrofit kit designed for use in 5" or 6" recessed housings. It features an E26 socket adapter, torsion springs for easy installation, and a 5-year warranty. The kit is not compatible with photo controls, occupancy sensors, or timing devices. Approved dimmers include:

  • AH Lighting: SDM3/1000/WHITE, SDM/600/WHITE
  • Almond LUXDM600-12
  • GE: 18024
  • Leviton: IPI06-1LZ, IPI10-1LZ, IPL06, 603-6631-A, 6631-A, 6631-LA, 6672, 6683, 6683-10Z, 6683
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents