Maxxima MRL-S20855 Installation guide

MRL-S20855
Brand
Maxxima
Model
MRL-S20855
Category
Floodlights
Type
Installation guide

Maxxima MRL-S20855 is a versatile 2-inch LED downlight designed for various applications requiring high-quality, energy-efficient lighting. With its adjustable color temperature (2700K to 5000K) and dimmable capabilities, you can customize the ambiance and brightness to suit your needs. The slim profile and trimless design allow for seamless integration into your ceiling, providing a modern and minimalist look. Installation is simplified with the included plaster frame and locking mechanism, making it suitable for both residential and commercial settings.

Maxxima MRL-S20855 is a versatile 2-inch LED downlight designed for various applications requiring high-quality, energy-efficient lighting. With its adjustable color temperature (2700K to 5000K) and dimmable capabilities, you can customize the ambiance and brightness to suit your needs. The slim profile and trimless design allow for seamless integration into your ceiling, providing a modern and minimalist look. Installation is simplified with the included plaster frame and locking mechanism, making it suitable for both residential and commercial settings.

2” and 4” Trimless Downlight Installation Guide
MRL-S20855, MRL-S20855S, MRL-S41555, MRL-S41555S
www.maxximastyle.com
1. Ensure the power has been turned off by switching the circuit breaker
to the off position or by removing the fuse from the fuse panel.
2. After marking the center point of where the fixture will be located,
using the provided template cut the required hole shown in figure 1
or figure 1A if the light is square.
3. Install the plaster frame into the new cutout and use four screws to
secure the plaster frame to the ceiling shown in figure 2.
4. Plaster over the plaster frame ensuring not to apply too much plaster
to fill beyond the raised rim shown in figure 3.
5. Open the junction box, remove the desired knockout and attach
a twin screw clamp connector (or similar).
6. Insert the supply wire through the twin screw clamp connector
(or similar).
7. Connect the hot (black) wire to the black wire, the neutral (white)
wire to the white wire and the ground (green/bare copper) wire to
the green wire using the provided wire nuts.
8. Put all of the wires into the metal junction box and close the
junction box.
9. Using the selector switch on the back of the fixture
the CCT can be changed to any of the five settings
(CCT settings are 2700K/3000K/3500K/4000K/5000K).
10. Connect the male output connector from the junction box with the
female connector from the fixture and tighten the locking nut.
11. Insert the junction box into the plaster frame, ensuring the junction
box is laying on the ceiling material. Then align the locking tabs
on the side of the fixture such that the fixture can be inserted
then turn the fixture until the fixture is locked into the plaster frame.
12. Installation is now complete, restore power and
the fixture is now operational.
INSTALLATION INSTRUCTIONS
info@maxximastyle.com 866-MAXXIMA (629-9462) www.maxximastyle.com 125 Cabot Court Hauppauge, NY 11788
3 YEAR WARRANTY
Maxxima extends a 3 year limited warranty to the original purchase that the products listed are free from defects in material and/or
workmanship only. Maxxima will replace any warrantied product to the original consumer/purchaser if the product fails because of defects
due to workmanship and/or materials within the limited warranty period. Limited warranty is not transferable and applies to the original
installation of the Maxxima product. This offer does not constitute in any way a product guarantee and Maxxima does not hereby assume
any obligation whatsoever beyond sending a free replacement product.
• Risk of electric shock - Disconnect power at the source
before installation.
• If you are unsure about the installation or the maintenance
of the fixture, please consult an electrician.
• Do not make or alter any holes in the wiring enclosure or
modify any electrical componentry.
CAUTIONS
• The fixture must be wired in accordance with
the National Electric Code (N.E.C) standards and
any applicable local codes or ordinances.
• Supply conductors must at least be rated for 90°C/194°F.
• This fixture is designed for use with 120Vac, 50/60Hz only.
WARNINGS
Figure 1 Figure 1A
Figure 2 Figure 3
Figure 4
Figure 5
Figure 6
  • Page 1 1

Maxxima MRL-S20855 Installation guide

MRL-S20855
Brand
Maxxima
Model
MRL-S20855
Category
Floodlights
Type
Installation guide

Maxxima MRL-S20855 is a versatile 2-inch LED downlight designed for various applications requiring high-quality, energy-efficient lighting. With its adjustable color temperature (2700K to 5000K) and dimmable capabilities, you can customize the ambiance and brightness to suit your needs. The slim profile and trimless design allow for seamless integration into your ceiling, providing a modern and minimalist look. Installation is simplified with the included plaster frame and locking mechanism, making it suitable for both residential and commercial settings.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents