Moxa MD-226 Series Quick setup guide

MD-226 Series
Moxa
Brand
Moxa
Model
MD-226 Series
Type
Quick setup guide

This manual is also suitable for

– 1 – – 2 – – 3 –
P/N: 1802002260010
*1802002260010*
MD-200 Series
Quick Installation Guide
First Edition, July 2015
Overview
The MD-200 marine display series is designed for durably reliable
service as an ECDIS display component. The MD-200 series offers
full range dimming and optional optical bonding, making it
well-suited not only for ECDIS applications, but also for a variety of
other bridge applications.
The MD-200 series features both AC and DC power inputs, and can
be conveniently installed on any bridge, without the need for extra
hardware.
Moxa’s marine displays are compliant with the most important
industrial marine standards, including IEC 60945, DNV, and
IACS-E10, giving strong assurance of their suitability for marine
applications.
The following lists the models in the MD-200 series:
• MD-226X: 26-inch display with 16:10 aspect ratio.
• MD-224X/MD-224Z: 24-inch display with 16:9 aspect ratio.
• MD-219X/MD-219Z: 19-inch display with 5:4 aspect ratio.
Package Checklist
Before installing the MD-200 series, verify that the package
contains the following items:
• MD-200 series display
• VGA cable
• DVI-D cable
• 2-pin terminal block x 1
• 5-pin terminal block x 2
• Documentation and software CD
• Quick installation guide (printed)
• Warranty card
NOTE: Please contact your sales representative if any of the above
items are missing or damaged.
Hardware Installation
Appearance
MD-226/224
MD-219
SavvyTouch Display Control Buttons
The following table describes the SavvyTouch display controls on
the front surface of the MD-200 series. These intelligent controls
will light up with a simple wave of your hand over the area of the
screen where they are located.
Name
Display
Color
Control Function/Color Legend
Menu/
Power
Green
Display is powered on and
functioning normally. Touch the
button to show the OSD settings
menu
Red
No input signal detected. Display
standby
Off
Power is down and the display is off
Brightness
White
+: To increase brightness of panel
-: To decrease brightness of panel
Info
Off AC/DC power is functioning normally
Display
mode
White
Switch between DAY/DUSK/NIGHT
brightness modes
Off
Panel brightness out of default range
Installing the MD-200 Series
Desktop
The MD-200 series comes with optional brackets that allow you to
install the display on a horizontal surface, such as a desktop. Three
round screws are required for each bracket. See the figure for
detailed screw specifications and their torque values.
Place your MD-200 series display on a clean, flat, well-ventilated
desktop. To protect the computer from overheating, leave some
ventilation space between the MD-200 series and other
equipment.
Do NOT place equipment or objects on the panel, as this might
damage internal components.
– 4 – – 5 – – 6 –
www.moxa.com/support
The Americas:
Europe:
Asia-Pacific:
China:
2015 Moxa Inc.All rights reserved.
Panel Mounting
The MD-200 series comes with 14 optional clamp mounts for
installation on a wall (where space has been cut out to
accommodate the rest of the hardware) or into computing stations
where a flush mount is desired.
The maximum thickness of the surface to which the
computer can be clamped is 11 mm. For a secure mounting, all
14 clamps must be used.
The clamp arms are fastened into slots on all four sides of the
MD-200 series. Use the short M4 SUS screws to fasten the clamp
arms to the MD-200 series mounting slots, as shown in the
following magnified inset in the diagram. Next, use the clamps to
fasten the MD-200 series to its mounting point; please note the
torque value as shown in the figure.
VESA Mounting
The MD-200 series also comes with an optional VESA mounting kit.
Six flat screws and four round screws are required to fasten the
VESA mounting bracket. See the following figure for detailed screw
specifications and torque values.
An additional four screws (not included in the kit) are required to
mount the display on a VESA rack. For this purpose, use M6 screws
that are between 10 and 12 mm in length.
Connector Descriptions
Extending the Display
The MD-200 series comes with both standard VGA and DVI-D
interfaces on the bottom panel. It automatically detects whether
the input video source is from the VGA or DVI-D interface.
Configuring the Display via the Serial Port
The MD-200 series has two serial ports. The RS-232 port uses a
DB9 connector, and the RS-422/485 port uses a terminal block
connector. Either serial port can be used to modify the display
parameters using UART commands. For information on serial port
configuration, see the MD-200 Series Hardware Manual.
The pin assignments for the ports are shown in the following table:
Pin
RS-232
1
DCD
2
RxD
3
TxD
4
DTR
5
GND
6
DSR
7
RTS
8
CTS
RS-422/485 (Terminal Block) Pinouts
Pin
RS-422
RS-485 (4-wire)
RS-485 (2-wire)
1
RxDB(+)
RxDB(+)
–
2
RxDA(-)
RxDA(-)
–
3
TxDB(+)
TxDB(+)
DataB(+)
4
TxDA(-)
TxDA(-)
DataA(-)
5
GND
GND
GND
Powering on/off the MD-200 Series
To power on the MD-200 series, connect the unit to an AC power
source, a DC power source, or both. Touch the MENU button for 1
second to turn on the display. Touch the MENU button for 4
seconds to turn off the display.
Grounding the MD-200 Series
Proper grounding and wire routing help to limit the effects of noise
from electromagnetic interference (EMI). Run the ground
connection from the ground screw to the grounding surface prior to
connecting the power source.
For detailed configuration of the MD-200 Series, refer to the
MD-200 Series Hardware Manual.
  • Page 1 1
  • Page 2 2

Moxa MD-226 Series Quick setup guide

MD-226 Series
Moxa
Brand
Moxa
Model
MD-226 Series
Type
Quick setup guide
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents