2. Focal Point
  3. Seem 2 LED Wall Mount FSM2LW

Focal Point Seem 2 LED Wall Mount FSM2LW Installation guide

  • Hello! I've reviewed the instructions for the LED Wall Mount FSM2W. This document provides detailed guidance on proper installation, including mounting procedures, electrical connections, and lens options. I'm here to help with any questions you might have about installing this device.
  • Who should install the luminaires?
    What should be done before installation or servicing?
    What are the different lens options?
IS0717 REV. C ©2022 Focal Point, LLC | 4141 S. Pulaski Rd., Chicago, IL 60632 | www.focalpointlights.com/reference 1 of 3
Seem 2 LED Wall Mount
Wall Mount | FSM2W
• Luminaires must be installed by a qualied
electrician (check with local and national
codes for proper installation).
• To prevent electrical shock, disconnect
electrical supply before installation or
servicing.
• Contractor is responsible for adequately
reinforcing walls and/or ceilings to support
xture weight.
• Focal Point, LLC accepts no responsibility
for inadequately reinforced walls and/or
ceilings.
• The information contained in this drawing
is the sole property of Focal Point, LLC.
Any reproduction in part or whole without
the written permission of Focal Point, LLC
is prohibited.
POWER OFF
POWER ON
ATTENTION
SEE ADDITIONAL
INSTRUCTIONS
BEFORE YOU BEGIN COMPONENT KEY
INSTRUCTION KEY
FOCAL POINT
Asymmetric /
Flush Lens
1.5" Pop-Down Lens
(individual housings only up to 8’)
0.5" Pop-Down Lens
U - Individual
S - Start of Run
I - Intermediate
E - End of Run
Individual
(Start of Run)
Intermediate
(End of Run)
MOUNTING RAIL
SHIPPED INSTALLED
Joiner Bracket
Assembly
(A48094-01)
Joiner Blocker
(A48495-01-WH)
Reector
Screw (72026)
(6-32 x 1/4 SELF TAP-
PING SCREW)
SHIPPED IN HARDWARE BAG
Extra Joiner Bracket
Assembly Screw
(700309)
Joiner Blocker
Screw (700348)
(6-32 x 5/16 SELF
TAPPING SCREW)
Asymmetric Lens Distribution Direction
IS0717 REV. C ©2022 Focal Point, LLC | 4141 S. Pulaski Rd., Chicago, IL 60632 | www.focalpointlights.com/reference 2 of 3
4
INDIVIDUAL UNIT INSTALLATION FOLLOW STEPS 1-6, 10 & 12
Avoid all contact with LED surface,
LEDs are easily damaged!
Locate j-box center & install (j-box by others. 4"X2" handy box.)
2' housing 3' & 6' housings
12.09" 18.09"
4', 7' & 8' housings 5' housing
Luminaire outline
Luminaire outline
Luminaire outline
Luminaire outline
24.09" 30.09"
2.72"
2.72"
2.72"
4.50"
4.50"
4.50"
4.50"
2.72"
(Fasteners by others)
2Install remaining rails.
Remove end section from last rail in run.
1
(Fasteners by others)
3
Individual and feed locations only
5
A
B
C
6
Dimensions shown are from the room side observing the wall
IS0717 REV. C ©2022 Focal Point, LLC | 4141 S. Pulaski Rd., Chicago, IL 60632 | www.focalpointlights.com/reference 3 of 3
11
12
8
11
79
MAKE ELECTRICAL CONNECTIONS
11
11
10
MAKE ELECTRICAL CONNECTIONS
Individual and feed
locations only
DRIVER SERVICE
21
Avoid all contact with LED surface,
LEDs are easily damaged!
X2
/