2. Focal Point
  3. Seem 2 LED Indirect FSM2IW

Focal Point Seem 2 LED Indirect FSM2IW Installation guide

  • Hello! I've read the user manual for the Focal Point Seem 2 Indirect FSM2IW wall mount luminaire. This manual provides detailed instructions for its installation, highlighting electrical safety, component usage, and the importance of proper wall reinforcement. I'm ready to answer your questions about the installation process or any other aspect of the product.
  • Who should install the luminaires?
    What precaution should be taken before installation or servicing?
    What type of conduit is recommended for electrical feed?
IS0752 REV. A ©2020 Focal Point, LLC | 4141 S. Pulaski Rd., Chicago, IL 60632 | www.focalpointlights.com/reference 1 of 3
Seem™ 2 Indirect
Wall Mount | FSM2IW
• Luminaires must be installed by a qualified
electrician (check with local and national
codes for proper installation).
• To prevent electrical shock, disconnect
electrical supply before installation or
servicing.
• Contractor is responsible for adequately
reinforcing walls and/or ceilings to support
fixture weight.
• Focal Point, LLC accepts no responsibility
for inadequately reinforced walls and/or
ceilings.
• The information contained in this drawing
is the sole property of Focal Point, LLC.
Any reproduction in part or whole without
the written permission of Focal Point, LLC
is prohibited.
BEFORE YOU BEGIN COMPONENT KEY
FOCAL POINT SHIPPED INSTALLED
U - Individual
S - Start of Run
I - Intermediate
Non-Feed
E - End of Run
Non-Feed
I - Intermediate
Feed
18.08"
1.22"
2.64"
Ø 0.875"
Dimensions shown are from the room side observing the wall.
Luminaire outline
1
Feed location is the same for all housing lengths
Mounting Screw
(700322)
(2 per luminaire)
Joiner Bracket
(A53548-01)
SHIPPED IN HARDWARE BAG
Mounting Rail
E - End of Run
Feed
INDIVIDUAL UNIT INSTALLATION FOLLOW STEPS 1-6, 11 & 12
Configurations are run specific,
please consult factory drawings
before beginning installation.
Joiner Screw
(72118)
POWER OFF
POWER ON
ATTENTION
SEE ADDITIONAL
INSTRUCTIONS
INSTRUCTION KEY
Use 1/2" trade size conduit
(by others) for electrical feed.
DO NOT USE J-BOX.
1 of 3
IS0752 REV. B
©2022 Focal Point, LLC | 4141 S. Pulaski Rd., Chicago, IL 60632 | www.focalpointlights.com/reference
IS0752 REV. A ©2020 Focal Point, LLC | 4141 S. Pulaski Rd., Chicago, IL 60632 | www.focalpointlights.com/reference 2 of 3
6
211
34
11
5
Avoid all contact with LED surface,
LEDs are easily damaged!
Install remaining rails (fasteners by others).
Remove end section from last rail.
Ø 1.00"
Electrical access cutout
x2 per housing
x2 per housing
Fasteners by others
7
810
11
11 12
Avoid all contact with LED surface,
LEDs are easily damaged!
Avoid all contact with LED surface,
LEDs are easily damaged!
Avoid all contact with LED surface,
LEDs are easily damaged!
9
2 of 3
IS0752 REV. B ©2022 Focal Point, LLC | 4141 S. Pulaski Rd., Chicago, IL 60632 | www.focalpointlights.com/reference
IS0752 REV. A ©2020 Focal Point, LLC | 4141 S. Pulaski Rd., Chicago, IL 60632 | www.focalpointlights.com/reference 3 of 3
DRIVER SERVICE
111
2
Avoid all contact with LED surface,
LEDs are easily damaged!
3 of 3
IS0752 REV. B ©2022 Focal Point, LLC | 4141 S. Pulaski Rd., Chicago, IL 60632 | www.focalpointlights.com/reference
/