2. Focal Point
  3. Seem 1 Wall Mount FSM1W

Focal Point Seem 1 Wall Mount FSM1W, Seem 1 Direct/Indirect Wall Mount FSM1BW Installation guide

  • Hello! I've reviewed the installation instructions for the Focal Point Seem 1 FSM1W and FSM1BW wall mount luminaires. This document outlines the necessary steps for a successful installation, including locating the J-box, installing rails, and making electrical connections. The instructions emphasize the importance of avoiding contact with the LED surface and the need for professional installation by a qualified electrician. I'm ready to answer any questions you have about the installation process or the product itself.
  • What type of J-Box is required?
    Who is responsible for the wall reinforcement?
    What should be avoided when handling the luminaire?
IS0680 Rev. F 2022 ©Focal Point, LLC 4141 S. Pulaski Rd., Chicago, IL 60632 | www.focalpointlights.com 1 of 2
Seem™ 1 wall mount
FSM1W | FSM1BW
focal point
U -
individUal
S -
Start of rUn
i -
intermediate
e -
end of rUn
individUal / Start of rUn
Luminaires must be installed by a qualied electrician (check with local and national codes for proper installation).
To prevent electrical shock, disconnect electrical supply before installation or servicing.
configUrationS are rUn Specific, pleaSe conSUlt factory drawingS before beginning inStallation.
Shipped in hardware bag
partS liStS
intermediate / end of rUn
2
(FASTENERS BY OTHERS)
moUnting Screw
(72007)
(2 per lUminaire)
Shipped inStalled
joiner
bracket
(a37351-01)
(700192)
1LOCATE J-BOX CENTER & INSTALL (J-BOX BY OTHERS. 4"x2" handy box.)
2' - 2'11" housing 3' - 3'11" & 6' - 6'11" housings
12.06" 18.06"
luminaire outlineluminaire outline
2.00"
3.50"
3.50"
2.00"
4' - 4'11", 7' - 7'11" & 8' housings 5' - 5'11" housing
luminaire outline
luminaire outline
24.06" 30.06"
2.00"
2.00"
3.50"
3.50"
23 INSTALL REMAINING RAILS.
REMOVE END SECTION FROM
LAST RAIL IN RUN.
(FASTENERS BY OTHERS)
key
power off
power on
attention
See additional
inStrUctionS
individUal inSallationS follow StepS 1-6, 10 & 11
prodUct id
label on
reflector
Contractor is responsible for adequately reinforcing walls and/or ceilings to support luminaire weight. Focal Point, LLC accepts no responsibility for inadequately reinforced walls
and/or ceilings. The information contained in this drawing is the sole property of Focal Point, LLC. Any reproduction in part or whole without the written permission of Focal Point, LLC
is prohibited.
IS0680 Rev. F 2022 ©Focal Point, LLC 4141 S. Pulaski Rd., Chicago, IL 60632 | www.focalpointlights.com 2 of 2
7
6
make electrical connections
4
AVOID ALL CONTACT WITH LED SURFACE,
LEDS ARE EASILY DAMAGED!
5REMOVE REFLECTORS ON
FEED LUMINAIRE ONLY
make electrical connections
10 11
8
AVOID ALL CONTACT WITH
LED SURFACE, LEDS ARE
EASILY DAMAGED!
driver Service
111
AVOID ALL CONTACT WITH LED SURFACE,
LEDS ARE EASILY DAMAGED!
2
WIRE NUTS BY OTHERS
ASYMMETRIC LENS DISTRIBUTION DIRECTION
make electrical connections
X2 PER HOUSING
9X2 PER HOUSING
/