ZENEC Z-E1010 User manual

Brand: ZENEC

Model: Z-E1010

Type: User manual

ZENEC Z-E1010 is a multimedia powerhouse for your car, combining cutting-edge technology with user-friendly features. Enjoy a seamless Android experience with the latest Android 7.1.2 operating system, offering a wide range of apps and customization options. Stay entertained on the road with a built-in media player that supports various audio and video formats, including high-resolution videos. Experience crystal-clear audio with the integrated amplifier and a variety of sound settings. Connect your smartphone effortlessly via Bluetooth for hands-free calling and audio streaming.

1 of 3 January 2022 / RevA

MIB1 – Z-E1010 Update Installation Instructions MainSystem

Requirements

ATTENTION: The Z-E1010 device must be prepared for operation and software installation with a frame kit-/ power cable suitable

for MIB1 vehicles.

After successful software installation, the Z-E1010 device must be set to MIB1 Low-Speed CAN data recognition (!) This is done

by changing a switch in the device setup of the Z-E1010.

Note: With the factory setting of the CAN data recognition in the device setup menu to MIB2, the Z-E1010 in MIB1 vehicles

receives no power when connected in the vehicle, since MIB1 low-speed CAN data are not recognized by the device.

The update consists of a complete MainSystem software update, which must be run from USB data carrier. You will need:

> USB removable storage device (USB stick) with at least 2 GB storage capacity.

> A PC or notebook with Windows operating system.

Please note:

• Before you start, the USB stick must be formatted with FAT 32. (Right-click on USB memory device in Windows Explorer.

Select "Format" > FAT 32 > Start.

• The ZENEC Z-E1010 restarts several times during the software update and stays off, among other things, for a few seconds

(black screen for approx. 5 ~ 10 sec.) before the device restarts. Please do not operate or switch off the device during the

update process. After successful installation the tuner source will come up.

Installation of the MainSystem software update via USB:

The MainSystem software can be found at: www.zenec.com > Support> Software Updates > Z-E1010

Link: http://www.zenec.com/support/software-updates/e-go-core-z-e1010/?lang=en

1. MIB1 power cable prepare for software installation – see MIB1 > MIB2 Setup Instructions

EGO_CORE_MIB1-MIB2_Setup_EN_RevA (Quadlock II cable harness preparation). Connect the female “ACC” bullet

connector to its male “ACC” counterpart. See  gure.

3. The software package is a self-unzipping executable. Start extraction with a double-click and select your USB stick as target

for the uncompressed  les.

4. You obtain a update  le called „Android7.1.2_20220112.20_zenec_core.img” in the root directory of the USB stick.

5. Connect the USB stick to the Z-E1010 USB-1 connection cable.

2. Download the Software Update "Z-E1010_Core_SW_v3.6.exe".

9. The update installs sequentially and the lower part of the display screen informs about the progress. The software installation

takes about 4~5 minutes.

10. After successful software installation, the device reboots serval time and then the MainMenu will show up.

11. Remove the USB stick.

2 of 3 January 2022 / RevA

MIB1 – Z-E1010 Update Installation Instructions MainSystem

7. The update dialog menu is shown. Make sure that, the checkboxes [TUNER DB] and [OS] are selected.

8. Tap on the „YES“ but ton to start the update process.

12. Attention: The desired vehicle platform (MIB1) must be set now. To change the platform type to MIB1 a password must be

entered (avoiding accidental change of platform setting).

13. In the device main menu, tap on the icon "Settings” ► “Password Function” and enter 808135. Con rm the password with

“OK”. And con rm the "MIB1 platform update" popup window with "YES".

14. The device does install the (MIB1-MCU) software and performs a reboot – platform switch changes to MIB1.

6. Go to the device menu:

Settings > System > Software Update and con rm by tapping on the green hook checkbox.

MIB1 – Z-E1010 Update Installation Instructions MainSystem

18. Version check

Please do not operate or switch off the device during the restart process (duration approx. 3 minutes).

After restart, the MainMenu will show up.

Note: After the loading factory defaults, some personal settings must be set again (such as camera grid lines, audio

settings etc.).

Version control

After installing the software update a version check needs to be carried out. In the device menu:

Settings > System > Software Version Info.

Version: v3.6

If the version differs from the target version, install the update anew.

3 of 3 January 2022 / RevA

Improvements – bug xes and function updates:

MAINSYSTEM

• Improved system stability and performance

• NEW: Abalta Weblink 2.0 runnable integration, i.e. Youtube, ShoutCast and Android audio / video player connectivity.

• NEW: Wi logic change that enables Wi use again.

• iGO protocol update to x the roundabout exit number ickering in the MFA*

*In combination with the latest iGO navigation software. Update is available via Naviextras Toolbox www.naviextras.com

TUNER

• NEW: Local tuner slideshow database update to v1.21

MEDIA PLAYER

• Bugx for last playback issue sometimes on USB-2

BLUETOOTH

• Font and brightness improvements in various Bluetooth pages

15. After successful MIB platform conguration (MIB-1 software installation) the main menu is displayed.

16. Now disconnect the cables with the "ACC" ag on the wiring harness.

17. Make a RESET by press and hold the "RST" button for 2~3 seconds with using of a pointed object.

ZENEC Z-E1010 User manual

ZENEC Z-E1010 User manual

Related papers

Other documents