Paradyne JetFusion 2000 Series User manual

JetFusion

Integrated Access Device

2000, 2100, 2200, 2300 Series

User’s Guide

Document No. 2000-A2-GB23-00

September 2004

A September 2004 2000-A2-GB23-00

Printed in U.S.A.

Notice

This publication is protected by federal copyright law. No part of this publication may be copied or distributed,

transmitted, transcribed, stored in a retrieval system, or translated into any human or computer language in any form or

by any means, electronic, mechanical, magnetic, manual or otherwise, or disclosed to third parties without the express

written permission of Paradyne Corporation, 8545 126th Ave. N., Largo, FL 33773.

Paradyne Corporation makes no representation or warranties with respect to the contents hereof and specifically

disclaims any implied warranties of merchantability or fitness for a particular purpose. Further, Paradyne Corporation

reserves the right to revise this publication and to make changes from time to time in the contents hereof without

obligation of Paradyne Corporation to notify any person of such revision or changes.

Changes and enhancements to the product and to the information herein will be documented and issued as a new

release to this manual.

Warranty, Sales, Service, and Training Information

Contact your local sales representative, service representative, or distributor directly for any help needed. For additional

information concerning warranty, sales, service, repair, installation, documentation, training, distributor locations, or

Paradyne worldwide office locations, use one of the following methods:

 Internet: Visit the Paradyne World Wide Web site at www.paradyne.com. (Be sure to register your warranty at

www.paradyne.com/warranty.)

 Telephone: Call our automated system to receive current information by fax or to speak with a company

representative.

— Within the U.S.A., call 1-800-870-2221

— Outside the U.S.A., call 1-727-530-2340

Document Feedback

We welcome your comments and suggestions about this document. Please mail them to Technical Publications,

Paradyne Corporation, 8545 126th Ave. N., Largo, FL 33773, or send e-mail to userdoc@paradyne.com. Include the

number and title of this document in your correspondence. Please include your name and phone number if you are

willing to provide additional clarification.

Trademarks

Acculink, Bitstorm, Comsphere, DSL the Easy Way, ETC, Etherloop, FrameSaver, GranDSLAM, GrandVIEW, Hotwire,

the Hotwire logo, Jetstream, MVL, NextEDGE, Net to Net Technologies, OpenLane, Paradyne, the Paradyne logo,

Paradyne Credit Corp., the Paradyne Credit Corp. logo, Performance Wizard, StormPort, TruePut are registered

trademarks of Paradyne Corporation.

ADSL/R, Connect to Success, Hotwire Connected, iMarc, JetFusion, JetVision, MicroBurst, PacketSurfer, Quick

Channel, ReachDSL, Reverse Gateway, Spectrum Manager, and StormTracker are trademarks of Paradyne

Corporation.

All other products or services mentioned herein are the trademarks, service marks, registered trademarks, or

registered service marks of their respective owners.

i

2004, 2008 2004s,

2008s, 2104, 2108,

2104s, 2108s

FCC Requirements

This equipment has been tested and found to comply with the limits for a Class A digital device

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference when the equipment is operated in a commercial environment.

Operation of this equipment in a residential area is likely to cause harmful interference, in which

case the user is required to correct the interference at the user’s own expense.

This equipment generates, uses, and can radiate radio frequency energy, and, if not installed and

used in accordance with the instruction manual, may cause harmful interference to radio com-

munications. However, there is no guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference to radio or television reception

(which can be determined by turning the equipment off and on), the user is encouraged to try to

correct the interference by taking one or more of the following measures:

• Reorient or relocate the receiving antenna

• Increase the separation between the equipment and receiver

• Plug the equipment into an outlet on a circuit different from that to which the receiver is currently con-

nected

• Consult the dealer or an experienced radio/TV technician for help

This device must also accept any interference received, including interference that may cause

undesired operation.

WARNING: The 2008 and 2108 are to be used only with a certified Class 2 power supply.

See Appendix C, “Specifications.”

WARNING: Changes or modifications to this unit not expressly approved by the party

responsible for compliance could void the user’s authority to operate the

equipment.

The 2x08 complies with Part 68 of the FCC Rules and the requirements adopted by the ACTA.

On the bottom of the 2x08 unit is a label that contains, among other information, a product iden-

tifier in the format of US:GICDDNANNE2x08. If requested, this number must be provided to

the telephone company.

1 All direct connections to network lines must be made using standard plugs and jacks

(compliant with Part 68 and the requirements adopted by the ACTA). A compliant telephone

cord with a modular plug is provided with this product. It is designed to be connected to a

compatible modular jack that is also compliant. See installation instructions for details. The

table below presents a list of applicable registration jack USOCs and facility interface codes

(FIC). These are required when ordering service from the telco.

2 If the unit appears to be malfunctioning, it should be disconnected from the network lines

until the source of trouble is determined to be your equipment or the telephone line. If your

equipment needs repair, it should not be reconnected until it is repaired.

3 If your telephone equipment causes harm to the telephone network, the telephone company

may discontinue your service temporarily. If possible, they will notify you in advance.

However, if advance notice is not practical, you will be notified as soon as possible. You will

be informed of your right to file a complaint with the FCC.

IAD Port ID REN/SOC FIC USOC

2008 ADSL 0.0B RJ11C

2108 SHDSL 0.0B RJ11C

ii 2000-A2-GB23-00

4 Your telephone company may make changes to its facilities, equipment, operations, or

procedures that could affect the proper functioning of your equipment. If they do, you will

be notified in advance so you can have the opportunity to maintain uninterrupted telephone

service.

5 If you experience trouble with the 2008/2108 units, please contact your service

representative for information on obtaining service or repairs. The telephone company may

ask that you disconnect this equipment from the network until the problem has been

corrected or until you are sure the equipment is not malfunctioning. No user serviceable

parts are contained in this equipment. This equipment may not be used for coin service

provided by the telephone company. Connection to party lines is subject to state tariffs.

Contact the state Public Utilities Commission or Corporation for information. Do not attempt

to repair this equipment yourself.

2004, 2008 2004s,

2008s, 2104, 2108,

2104s, 2108s

Canadian Emissions

Requirements

This digital apparatus does not exceed the Class A limits for radio noise emissions from digital

apparatus set out in the Radio Interference Regulations of the Canadian Department of Commu-

nications.

Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les limites appli-

cables aux appareils numériques (de la class A) prescrites dans le Règlement sur le brouillage

radioélectrique edicté par le ministère des Communications du Canada.

2208, 2208s, 2304,

2308, 2304s, 2308s