Norac UC7-BC-GA02 Installation guide

Brand: Norac

Model: UC7-BC-GA02

Type: Installation guide







GoldacresG8andPrairieSeries1

PassiveRoll

UC7BoomHeightControlSystem

InstallationManual



ReorderP/N:UC7‐BC‐GA02‐INSTRevB(GoldacresG8andPrairieSeries1PassiveRoll)



NOTICE:NORACSystemsInternationalInc.reservestherighttoimproveproductsandtheirspecificationswithoutnoticeandwithouttherequirementtoupdate

productssoldpreviously.Everyefforthasbeenmadetoensuretheaccuracyoftheinformationcontainedinthismanual.Thetechnicalinformationinthismanual

wasreviewedatthetimeofapprovalforpublication.

WWW.NORAC.CA

PRECISIONDEFINED



Contents



Introduction..........................................................................................................................1



TechnicalSpecifications........................................................................................................2



PartsOverview......................................................................................................................3



Pre‐InstallationChecklist.......................................................................................................7



HydraulicInstallation.............................................................................................................8



UltrasonicSensorInstallation..............................................................................................11



ElectronicInstallation..........................................................................................................15



SoftwareSetup....................................................................................................................19



CableSchematics.................................................................................................................20



AppendixA:SevereTerrainOption.....................................................................................25





WWW.NORAC.CA

PRECISIONDEFINED





Page1

Visitwww.solutions.norac.caformoresystem

installationandtroubleshootinginfo.

1 Introduction

CongratulationsonyourpurchaseoftheNORACBoomHeightControlSystem.Thissystemismanufactured

withtopqualitycomponentsandisengineeredusingthelatesttechnologytoprovideoperatingreliability

unmatchedforyearstocome.

Whenproperlyusedthesystemcanprovideprotectionfromsprayerboomdamage,improvesprayerefficiency,

andensurechemicalsareappliedcorrectly.

Pleasetakethetimetoreadthismanualcompletelybeforeattemptingtoinstallthesystem.Athorough

understandingofthismanualwillensurethatyoureceivethemaximumbenefitfromthesystem.

Yourinputcanhelpmakeusbetter!Ifyoufindissuesorhavesuggestionsregardingthepartslistorthe

installationprocedure,pleasedon’thesitatetocontactus.



SeeGA8700640foradditionalinstallationinformation.



Everyefforthasbeenmadetoensuretheaccuracyoftheinformationcontainedinthismanual.Allparts

suppliedareselectedtospeciallyfitthesprayertofacilitateacompleteinstallation.However,NORACcannot

guaranteeallpartsfitasintendedduetothevariationsofthesprayerbythemanufacturer.

Pleasereadthismanualinitsentiretybeforeattemptinginstallation.

WWW.NORAC.CA

PRECISIONDEFINED





Page2

Visitwww.solutions.norac.caformoresystem

installationandtroubleshootinginfo.

2 TechnicalSpecifications

  

CANICES‐3(A)/NMB‐3(A)



ThisClassAdigitalapparatuscomplieswithCanadianICES‐003.

PursuanttoEMCDirective–Article9,thisproductisnotintendedforresidentialuse.

Table1:SystemSpecifications

SupplyVoltage(rated) 12VDC

SupplyCurrent(rated) 10A

HydraulicPressure(maximum) 3300psi

BaudRate 250kbps

OperatingTemperatureRange 0°Cto80°C





WWW.NORAC.CA

PRECISIONDEFINED





Page3

Visitwww.solutions.norac.caformoresystem

installationandtroubleshootinginfo.

3 PartsOverview

3.1. ElectronicInstallationOverview



Figure1:ElectronicInstallationOverview

ItemsshowninBLUEareincludedinthedisplaypackageandmaynotbeexactlyasshown.

WWW.NORAC.CA

PRECISIONDEFINED





Page4

Visitwww.solutions.norac.caformoresystem

installationandtroubleshootinginfo.

3.2. HydraulicPlumbingSchematic



Figure2:HydraulicPlumbingSchematic



WWW.NORAC.CA

PRECISIONDEFINED





Page5

Visitwww.solutions.norac.caformoresystem

installationandtroubleshootinginfo.

3.3. ListofParts

ItemPartNumberNameQuantity

B0544706‐01KITCABLETIEBLACK10PCS21IN150PCS7.5IN1

B1244747SPACER2INSQUARETUBING8IN2

B1550919MOUNTINGBRACKETMANIFOLD509W/HARDWARE1

B2044971SENSORMOUNTINGBRACKETLOWPROFILE16GA2

C0143220‐01CABLENETWORK14AWG1M3

C0543210‐10CABLENETWORK18AWG10M5

C1050130‐01CABLEVALVE4‐PINDTTO2‐PINDT2

C201032082‐01HRNSUC7GOLDACRESINTERFACETILT1

C211037051‐01HRNSUC7GOLDACRESINTERFACEMAIN‐G81

C3043250‐06CBL,PWRPIGTAILFUSED1

E0150000HCM1MODULE1

E0750300ULTRASONICMAXSENSOR3

E1143765NETWORKCOUPLER8‐WAY1

E1243764NETWORKCOUPLER2‐WAY3

E2043764TNETWORKCOUPLER2‐WAYWITHTERMINATOR 2

H1044865‐34HYDRAULICSFITTINGKIT‐GN11

M02UC7‐BC‐GA02‐INSTMANUALINSTALLATIONUC7GOLDACRESG8ANDPRAIRIEPASSIVEROLL1

M05106706MOUNTINGCLIPHCM12

M20ACT‐MOD‐30000ACTIVATION–GENERICPR1

P01106705NETWORK4PINCAVITYPLUG1

P03105882NETWORK6PINPLUG4

P04106027NETWORK2PINRECEPTACLEPLUG1

P05411785CONNDTCHDT4PINPLUGW/TETHER1

V0150902VALVEASSEM2STATIONCCPROPDT1

V0250906VALVELOADSENSESANDWICHKITD032STN1





WWW.NORAC.CA

PRECISIONDEFINED





Page6

Visitwww.solutions.norac.caformoresystem

installationandtroubleshootinginfo.

3.3.1. HydraulicFittingKitDetails(P/N:44865‐34)

ItemPartNumberNameQuantityPicture

F07103312MALEADAPTER‐6MB6MJ6



F0844928ORIFICEINSERT.047INONEWAY4



F09104369PLUG‐6MBP2



Notallfittingsareusedforthisinstallation.



Donotusehighspeedpowertools/drillswheninstallinghardware.



TheuseofdielectricgreaseisnotrecommendedonanyNORACelectricalconnections.



ToensureallstainlesssteelhardwaredoesnotgallorseizeapplyalightcoatingofthesuppliedPermatex

Anti‐seizegreasetoallthreadedpartsuponinstallation.PermatexAnti‐seizelubricantispreferred,butother

similaranti‐seizeproductsmaybeused.



6 M B - 6 M OR X 90

SIZE IN

1/16TH'S

GENDER: MALE

OR FEMALE

90° ANGLE

SWIVEL

TYPE

GENDER

SIZE

TYPE:

B - ORB

J - JIC

OR - FLAT

FACE

P - PIPE

Fitting Name

Example:

WWW.NORAC.CA

PRECISIONDEFINED





Page7

Visitwww.solutions.norac.caformoresystem

installationandtroubleshootinginfo.

4 Pre‐InstallationChecklist

Thepre‐installchecklistisnecessarytochecktheexistingsprayerfunctionalitybeforetheinstallation.

1. Unfoldthesprayeroveraflat,unobstructedarea(i.e.nopowerlines…etc.).

2. Ensureallboom‐foldoperationsarefunctional(placeacheckmarkinboxesbelow).

3. Bringenginetofield‐operationalRPMandrecordbelow.

4. Recordthetime(seconds)ittakesforafullstrokeforallboomfunctions.Toensurerepeatable

measurements,taketheaverageof3trials.

5. NotallsprayerswillhavethefunctionslistedbelowinFigure3.



Ensuretheboomhassufficienttravelsoitdoesnotcontactthegroundduringthesetests.



Figure3:Pre‐InstallBoomSpeeds





WWW.NORAC.CA

PRECISIONDEFINED





Page8

Visitwww.solutions.norac.caformoresystem

installationandtroubleshootinginfo.

5 HydraulicInstallation



Ensureallpressurehasbeenbledfromthesystembeforedisconnectinganylinesorfittings.Hydraulic

pressurewillexistonthewingtiltcircuitsunlessthewingsarebeingsupportedbyothermeans.Thehydraulic

installationmaybeperformedwiththewingsintransportposition,restingonthegroundorwiththetilt

cylindersfullyextended.



ComponentfailureduetooilcontaminationisnotcoveredundertheNORACsystemwarranty.Itis

recommendedthataqualifiedtechnicianperformthehydraulicinstallation.

5.1. LoadSensePlateAssembly

1. Removethesolenoidvalvesfromthetopofthemanifold.

2. Placetheloadsensesandwichplateontothemanifoldaligningthemountingholes.

3. Thesurfaceofthesandwichwitho‐ringsinstalledmatesagainstthemanifold.

4. Onthe2stationsandwichblock(V02),theLSportsfacethepressure“P”endofthemanifold.

5. Placethesolenoidvalvesontopofthesandwichblock.The“P”labelonthesideofeachsolenoidmust

pointtowards“P”portofthemanifold.

6. InstallthelongerM5socketheadcapscrewssuppliedwiththesandwichblock.

7. Snugeachboltbeforetightening.

8. Torqueeachboltusingacornertocornerpatternto60‐65in‐lbs.(6.8‐7.3Nm)



Figure4:LoadSensePlateAssembly

WWW.NORAC.CA

PRECISIONDEFINED





Page9

Visitwww.solutions.norac.caformoresystem

installationandtroubleshootinginfo.

5.2. ValveBlockAssembly

1. Onacleansurfaceremovetheplasticplugsfromtheblock.

2. Insertthetwoorifices(F08)intothe“B”portswiththenotchfacingout.

3. Installthe6MB‐6MJ(F07)fittingsintothe“B”ports.Tightento18ft‐lbs(24Nm).

4. Insertthetwoorifices(F08)intothe“A”portswiththenotchfacingin.

5. Installthe6MB‐6MJ(F07)fittingsintothe“A”ports.Tightento18ft‐lbs(24Nm).

Figure5:NORACValveBlockDetails



5.3. ValveBlockMounting

1. Mountthevalveblockonthesprayerneartheexistingvalveblock.

2. Usethesuppliedbracket(B15)toinstallthevalveblock.

3. InserttheM8mountingstudsintotheblockusingahexnuttoholdthestud.Themanifoldmountingholes

areM8‐1.25x19mm(0.75”)deep.Ifboltsareusedinsteadofthestuds,ensuretheboltsthreadinatleast

10mm(3/8”).ApplyalightcoatingofthesuppliedPermatexAnti‐seizegreasetoallthreadedpartsupon

installation.

4. Usetheremaininghardwaretosecuretheblocktothesprayer.

5. Cutoffexcessthreadedrod,ifnecessary.



WWW.NORAC.CA

PRECISIONDEFINED





Page10

Visitwww.solutions.norac.caformoresystem

installationandtroubleshootinginfo.

5.4. HydraulicPlumbing



From this point on in the installation the booms will be inoperative until the hydraulics are fully

installed.

1. AftertheNORACvalveismounted,thehydraulichosesandfittingscanbeplumbed.Theplumbingforthe

hydrauliccircuitisshownschematicallyinFigure2.

2. Disconnectthetiltraiseandlowerlinesfromthesprayervalveblockandconnectfourteesontothevalve

block.

3. Connectthetiltraiseandlowerlinestothetees.

4. ConnectfourhydraulichosesfromthefreeendsoftheteestotheNORACvalveblock.Theraiselinesmust

beconnectedtothe“B”portsandthelowerlinesmustbeconnectedtothe“A”ports.

5. Disconnectthetanklinefromthesprayervalveblockandinsertateebetweenthehoseandthevalve

block.ConnectahydraulichosefromthefreeendoftheteetothetankportontheNORACvalveblock.

6. Disconnectthepressurelinefromthesprayervalveblockandinsertateebetweenthehoseandthevalve

block.ConnectahydraulichosefromthefreeendoftheteetothepressureportontheNORACvalve

block.

7. Disconnecttheloadsenselinefromthesprayervalveblockandinsertateebetweenthehoseandthe

valveblock.ConnectahydraulichosefromthefreeendoftheteetotheloadsenseportontheNORAC

valveblock.



Startupthesprayerandtestthesprayer’sfunctionality.Unfoldtheboomsandraise/lowereachboomand

themainsection.Ensurethattherearenoleaks.



WWW.NORAC.CA

PRECISIONDEFINED





Page11

Visitwww.solutions.norac.caformoresystem

installationandtroubleshootinginfo.

6 UltrasonicSensorInstallation

6.1. UltrasonicSensorMountingGuidelines

Thefollowingguidelineswillensureoptimalsensorperformanceandpreventsensormeasurement.

1. Initslowestposition,thesensormustbe9inches(230mm)ormorefromtheground.

2. Ensurethattherearenoobstructionswithina12inch(300mm)diametercircleprojecteddirectlybelow

thecenterofthesensor.

3. Thesensorshouldbeapproximatelyverticalatnormaloperatingheights.



Figure6:SensorMountingGuidelines



Figure7:BracketMountingGuidelines

6.2. LowProfileBracketMountingGuidelines

1. Minimizethedistancebetweentheboltstopreventbendingthebracketandpreventthebracketfrom

looseningovertime.

2. Ensurethebracketismountedtightagainstthebottomoftheboom,minimizingthedistancebetweenthe

boomstructureandtheangledflange.



Aproblemcanariseifasensorisnotmountedcorrectly.Thismayonlybecomeapparentoncethecontrol

systemisswitchedfromsoiltocropmode.

Becarefulthatthesensorbracketdoesnotcollidewithanyotherpartoftheboomwhentheboomisfolded

totransportposition.Ifpossible,mountthesensorbracketswhiletheboomsarefoldedtoensuretheywill

notcauseinterference.

WWW.NORAC.CA

PRECISIONDEFINED





Page12

Visitwww.solutions.norac.caformoresystem

installationandtroubleshootinginfo.

6.3. WingSensorInstallation

WheninstallingtheMAXSensors™(E07),startwiththesmallestserialnumberontheleft‐handsideandproceed

tothelargestserialnumberontheright‐handside.Eachsensorhasaserialnumberstampedonthesensor

housing.

ApplyalightcoatingofthesuppliedPermatexAnti‐seizegreasetoallthreadedpartsuponinstallation.



Figure8:SensorSerialNumberArrangement

1. Thesensorbracketshouldbeorientedforward(aheadoftheboom).

2. Typically,thebestmountinglocationforthewingsensorbracketswillbeneartheendoftheboomtips,

approximatelytwofeet(0.6m)fromtheend.Usespacers(B12)tomountthebrackets.

3. MounttheMAXsensors(E07)intothesensorbrackets.TorquetheM8nutto108in‐lb(12Nm).Runthe

sensorcablethroughholeinthebackofthebracket.Ensurethecableisclearofmovingpartsandwillnot

bedamagedduringfolding.

4. ConnecttwocablesC05togetherwitha2‐waycoupler(E12).Connectoneendtothe8‐waycouplerand

routealongtheboomtotheouterwingsensors.Positionthe2‐waycoupler(E12)approximatelyhalf‐way

betweenthechassisandtheouterwingsensors.

5. Atthesensorbrackets,attacha2‐waycouplerwithterminator(E20)tothesprayerboom.The2‐way

couplerwithterminatoristhewhite2‐waycoupler.PlugthesensorandtheCANbuscableintothe

terminator.

WWW.NORAC.CA

PRECISIONDEFINED





Page13

Visitwww.solutions.norac.caformoresystem

installationandtroubleshootinginfo.

  

Figure9:BracketMountingExample

Figure10:SpacerPlacement





Front

Spacer

(B12)

WWW.NORAC.CA

PRECISIONDEFINED





Page14

Visitwww.solutions.norac.caformoresystem

installationandtroubleshootinginfo.

6.4. MainLiftSensorInstallation

1. Thereareavarietyofwaystomountthemainliftbracketonmostsprayers.Thebracketshouldposition

thesensorapproximatelyinthecenterofthesprayer,forwardoftheboom.Anexampleofthismounting

isillustratedinFigure11.

2. MounttheMAXsensortothemainliftbracket.TorquetheM8nutto108in‐lb(12Nm).Runthesensor

cablethroughtheholeandbehindthebracket.

 

Figure11:ExampleMountingoftheMainLiftBracket



Ensurethebracketdoesnotcollidewithanyotherpartofthesprayerthroughoutthefullrangeofmainlift

motion.



WWW.NORAC.CA

PRECISIONDEFINED





Page15

Visitwww.solutions.norac.caformoresystem

installationandtroubleshootinginfo.

7 ElectronicInstallation

7.1. HCM1Installation

1. Verifythevalvecoilconnectorsareorientedvertically(Figure12).Looseningthelargeplasticnutwillallow

theconnectortoberotated.



Figure12:AlignCoils



Figure13:HCM1Connections



Figure14:HCM1Label

2. Laythelongerbranchofthevalvecables(C10)acrossthecoilswithone4‐pinconnectoroneachside.Do

notconnectthecablesatthistime.

OutputNumberNormalFunction

1,2LeftUpandDown

3,4RightUpandDown

5,6MainUpandDown

7,8RollCWandCCW

WWW.NORAC.CA

PRECISIONDEFINED





Page16

Visitwww.solutions.norac.caformoresystem

installationandtroubleshootinginfo.



Figure15:CablesUnderMountingClips(SideView)



Figure16:CablesLaidAcrossValveCoils(TopView)

3. PlacetheHCM1(E01)betweenthevalvecoils.Orientthe6‐pinDeutsch(CANbus)connectorstowardsthe

“P”and“T”portswiththelargelabelandLEDsfacingup.

4. SlidethemountingclipsovertheconnectorsoftheHCM1andthevalvecoilconnectors.Thismayrequire

flexingtheplasticbracketslightly.Ensuretheclipispushedovertheconnectorsfarenoughtoallowthe

clipstoengagebehindthevalveconnectors.

5. Connectthevalvecables(C10)tothevalvecoilsandtheHCM1.Thecableconnectedtotheleftconnector

(1,2)shouldbeconnectedtothecoilclosesttothe“P”and“T”ports.Thecableconnectedtotheright

connectorontheHCM1(3,4)shouldbeconnectedtothecoilfurthestfromthe“P”and“T”ports.



Figure17:HCM1andClipInstallation

6. ConnectcableC21totheHCM1.Connectthe4‐pinconnectorlabeled“TempProbe/Bypass”tothetemp/9

connectorontheHCM1.Connectthe4‐pinconnectorlabeled“MainDrive”tothe5,6connectoronthe

HCM1.TeetheconnectorsoncableC20intotheunloader,mainup,andmaindownfunctions.

7. ConnectthetemperatureprobeoncableC21totheholelabelled“TP”onthevalveblockusingthesupplied

3/8”x1/2”(9.5mmx25mm)bolt(Figure18).

8. Insert4‐pinplugs(P01)intoanyunusedconnectorsontheHCM1.

9. Connectthe12‐pinconnectoroncableC20totheHCM1.TeetheconnectorsoncableC20intotheleft

up,leftdown,rightup,andrightdownfunctions.



WWW.NORAC.CA

PRECISIONDEFINED





Page17

Visitwww.solutions.norac.caformoresystem

installationandtroubleshootinginfo.



Figure18:ValveBlockwithTemperatureProbeInstalled



Ensurethatallunusedconnectorsaresealedwiththeplugsprovided.

10. Connectthepowercable(C30)tothe3‐waycouplerfromthedisplaykit.Connecttheoppositeendofthe

cabletothejoystickauxpowerconnectioninthecabinwith8mmeyelets.



Figure19:PowerConnection





Page is loading ...

Norac UC7-BC-GA02 Installation guide

Norac UC7-BC-GA02 Installation guide

Norac UC7-BC-GA02 Installation guide

Related papers

Other documents