Candy LB CTAS 85 User manual
- Category
- Washing machines
- Type
- User manual
3
EN
When contacting a CANDY or one of its Technical Assistance Cen-
tre always refer to the model (see control panel) and the registration
and series numbers which are indicated at the bottom of the machine
under the lower panel or on the warranty certificate. That is to say,
everything that appears in the box.
Providing this information will ensure a faster and more efficient service.
This Instruction Manual
contains everything you need to
know about the everyday
running of your machine. Keep
it for future reference.
An Installation and
Maintenance Manual is also
provided which you should
consult during the installation
and routine maintenance of
your washing machine. The ma-
nual also contains information
about possible working
problems, advice about the
wash load, an explanation of
label symbols and hints about
how to remove stubborn stains.
INTRODUCTION
Read this manual carefully as it offers practical advice to help you get the most from your
washing machine.
1.- CONTROL PANEL
2.- LID
3.- DRUM
4.- DETERGENT COMPARTMENT
5.- FILTER DOOR
6.- FILTER
4
INDEX
GUARANTEE ................................................................................
5
TECHNICAL DATA ..........................................................................
6
OPENING THE LID – LOADING ...................................................
7
DETERGENT DISPENSER ...........................................................
8
ACTIVA SYSTEM ...........................................................................
9
FUZZY LOGIC ................................................................................
9
PROGRAMME SELECTION ..........................................................
9
CONTROL DESCRIPTION ..........................................................
10
TABLE OF PROGRAMMES .......................................................
14
page
Place the adhesive label, in the
corresponding language, in the
support that slots into the back of the
panel display.
5
GUARANTEE
1.
The appliance comes with a guarantee certificate.
2.
Complete part B and keep it in a safe place. It should
be presented to the Technical Assistance Centre in
the event of a repair being necessary along with the
legal receipt issued by the dealer on purchase.
3.
Do not forget to send part A of the Guarantee
Certificate to be validated within 15 days of purchase.
6
4,5
230
175
300
30
1.950
2.200
10
0,05 min.
0,8 max.
850
48
0,85
A
TECHNICAL DATA
Load capacity .................................................................
kg.
Voltage .............................................................................
V.
Wash motor power rating ................................................
W.
Spin motor power rating ..................................................
W.
Electropump power rating ...............................................
W.
Heating element power rating .........................................
W.
Max. power input .............................................................
W.
Fuse .................................................................................
A.
Water pressure ............................................................
MPa
Spin speed .......................................................
r.p.m./min
Water consumption (60º C programme) ..........................
lit.
Energy consumption (60º C programme) / 4,5 kg .......
kWh
Energy efficiency rating ........................................................
CTAS 85
7
OPENING THE DRUM
1.
Lift the lid (A) and open completely. Next open the drum
door following these instructions:
2.
Press catch (B) and kept it pressed down.
Press the first shutter (C) to unlock the two shutters (C)
and (D).
3.
Open the second shutter (D). Open the first shutter (C).
Place the washing in the drum.
4.
Close the first shutter (C).
Close the second shutter (D) so that the catch on the
first shutter fits correctly into the slot. Release.
5.
Ensure that both shutters are perfectly aligned and properly
closed.
IMPORTANT: IT IS IMPORTANT TO MAKE SURE THAT
THE DRUM IS CAREFULLY CLOSED BEFORE
OPERATING THE MACHINE, OTHERWISE THE
MACHINE OR LAUNDRY COULD GET DAMAGED.
2 min.
A
FRONT OF THE
WASHING MACHINE
C
B
D
WASHING MACHINE
LID
FRONT OF THE
WASHING MACHINE
D
C
FRONT OF THE
WASHING MACHINE
D
C
FRONT OF THE
WASHING MACHINE
C
D
IMPORTANT: A SPECIAL
SAFETY DEVICE
PREVENTS THE LID FROM
BEING OPENED
IMMEDIATELY AFTER THE
WASH HAS FINISHED.
ONCE THE SPIN CYCLE
HAS FINISHED, WAIT FOR
2 MINUTES BEFORE
TRYING TO OPEN THE LID.
8
DETERGENT DISPENSER
The detergent dispenser is divided into 4 compartments:
• Compartment I, is for prewash powder detergent. The recommended quantity is
60 gm of detergent (for 4,5 kg of laundry).
• Compartment II, is for wash powder detergent. The recommended quantity is 120
gm of detergent (for 4,5 kg of laundry).
• The compartment is for bleach. The recommended quantity is 7 cl.
• The compartment is for fabric conditioners, scenting agents and special
additives. The recommended quantity is 5 cl.
The detergent compartment has two guidance lines:
• RECOMMENDED (lower line). This indicates the recommended level for the prewash
and wash compartments.
• MAX. This indicates the maximum level which should never be exceeded.
MAXIMUM
(wash)
MAXIMUM
(bleach and scenting agent)
MAXIMUM
(prewash)
RECOMMENDED
9
This washing machine automatically adapts the water level to the type and quantity of clothes
to be washed. So it is possible to obtain a «customised» wash, even in terms of energy. This
system reduces water and energy consumption and provides an appreciable reduction in
wash time
PROGRAMME SELECTION
Select as follows:
• Check the programme table and set the desired programme using selector
(A)
• Select the options as permitted: the options available via the keys depend on
which programme is selected. If a key flashes when pressed, the options it offers are
not available. If it remains lit, they are. Options can be seen on the display (V).
• Press the Start/ Pause button. The door lock lamp will light up and the display will
show three dashes (- - -) and then the average duration of the programme selected.
After 10-15 minutes, during which time the water temperature, amount of washing,
etc. are determined, the display will show the time remaining to the end of the wash
cycle.
• Because the machine is electronic, the programme may take up to one minute to
commence. Its fuzzy logic programming technology gives this machine smart
monitoring capabilities, enabling it to adapt water levels, washing rates and spin
speeds with no further intervention by the user.
NOTE: A special memory unit stores the programme choice in case of power failure, so that
the machine will resume washing at the point where it left off when power is restored.
END OF CYCLE: At the end of the cycle the lights go out and the display reads (0 0 0). After
2 minutes, the display begins to flash. This means that the washing can be removed.
Press Start/ Pause and set the control to OFF.
ACTIVE SYSTEM
The Active system owes its efficiency to its capacity to take advantage of all the force of the
water. During the washing phases the water in the drum is pumped towards an injector
located in the drum which injects a powerful water jet onto the wash. This action with an
increase of rotation speed up to 100 revolutions guarantees an optimum quality of wash
and more thorough rinsing.
10
DESCRIPTION OF CONTROLS
PROGRAMME/ TEMPERATURE SELECTOR ...........................
DISPLAY: Delayed start, Spin-speed, Temperature,
Time remaining ...........................................................................
SUPER FAST button ..................................................................
ACTIVA RINSE button ................................................................
EASY IRON button .....................................................................
SPIN REGULATION button ........................................................
DELAYED START button ............................................................
START/ PAUSE button ...............................................................
Door secure/ door lock lamp .......................................................
Programme/ temperature table ...................................................
Marker dot ...................................................................................
A
V
D
E
F
C
I
H
G
P
p
CTAS 85
11
A
. PROGRAMME/ TEMPERATURE SELECTOR
Use this control to select the desired wash programme/
temperature. Turn the control to bring the marker dot (p)
into line with the number or symbol of the desired
programme. Temperature selection depends on the
programme selected. The display shows the temperature
or the relevant readings for special programmes.
For programme selection, follow the programme table.
To
change settings or programmes when a programme
is under way, proceed as follows:
- Press Start/ Pause. The display will read (0 0 0).
- Select the new programme with the selector. The temperature of the programme selected
or the relevant indication for special programmes will appear.
- Press Start/ Pause again.
- The machine will run the new programme.
To
add more washing when the programme is under way, proceed as follows:
- Hold down Start/ Pause until the display shows three dashes (- - -).
- When the Door Secure lamp goes off, open the door and add more washing.
- Close the doors of the drum and the outer cover.
- Press Start/ Pause.
THIS CONTROL TURNS BOTH WAY
V
. DISPLAY: Delayed start, Spin speed, Temperature, Time remaining.
Display as per function indicated.
NOTE: Only lit buttons are enabled: if a button flashes the options it offers are not available
in the programme selected.
To change options when a programme is under way, proceed as follows:
-Press Start/ Pause until the display shows three dashes (---), then flashes the
temperature of the programme selected.
- Make the change desired (e.g. reduction of spin speed).
- Press Start/ Pause. The time remaining to the end of the programme will appear on
the display.
- The machine will resume the programme with the new setting.
USE OF THE SELECTION CONTROLS
PROGR. & TºC
12
D
. SUPER FAST BUTTON
This function decreases programme time to a maximum of 50 minutes,
depending on the programme and wash temperature selected. The Su-
per Fast button can be used with loads of 1 – 4.5 kg, but only with cotton
and mixed/ synthetics programmes.
E
. ACTIVA RINSE BUTTON
This button engages a rinse function with high water levels and repeated
filling/ emptying combined with drum rotation cycles to ensure a perfect
rinse. Its use is recommended for children’s clothes or highly soiled clothing
requiring more washing powder than usual, and for fabrics whose fibres
have a tendency to retain washing products.
F
. EASY IRON BUTTON
This button works in all programmes except the cotton programme, the
32-minute cycle and the Mix & Wash System.
This function minimises wrinkling of fabrics during wash programmes. It
works in different ways with different programmes.
In cotton programmes the machine stops on the last rinse, leaving the clothes soaking. To
spin clothes and complete the programme, press the button again to release it.
In mixed/ synthetics programmes this button cuts out the intermediate spins and runs the
final spin at low speed to minimise twisting of clothes.
In delicates, wool and hand wash programmes it stops on the last rinse, leaving the
clothes soaking. To spin clothes and complete the programme, press the button again to
release it.
To empty the machine only:
- Press Start/ Pause.
- Set the programme selector to OFF.
- Select the emptying programme .
- Wait 5 seconds.
- Press Start/ Pause.
USE OF THE SELECTION CONTROLS
13
USE OF THE SELECTION CONTROLS
C
. SPIN REGULATION BUTTON
This key selects the spin speed for the last rinse.
When it is pressed, the display shows the options permitted under the
programme selected.
The display reads 0 for no spin and a sequence from 4 to 8 for speeds of 400 to 850 rpm.
For cotton programmes the options available are 850 to 400 and 0 (no spin).
For mixed/ synthetics programmes the options are 800 to 400 and 0 (no spin).
For delicates programmes the options are 800 to 400 and 0 (no spin).
For wool programmes the options are 800 to 400 and 0 (no spin).
For the hand wash programme the options are 800 to 400 and 0 (no spin).
For the rinse programme the options are 800 to 400 and 0 (no spin).
For the spin programme the options are 850 to 400 and 0 (no spin).
For the emptying programme there is no spin option.
For the Mix & Wash System programme the options are 850 to 400 and 0 (no spin).
For the 32 minute cycle programme the options are 800 to 400 and 0 (no spin).
I
. DELAYED START BUTTON
From 0 to 23 hours. Available on all programmes. When this button is
pressed the display shows the number of hours’ delay before the
programme starts. The delay increases by one hour each time the key is
pressed.
G
. DOOR SECURE/DOOR LOCK LAMP
H
. START/PAUSE BUTTON
14
•
•
•
WHITE
FAST COLOURS WITH PRE-WASH
FAST COLOURS
FAST COLOURS
DELICATE COLOURS
DELICATE COLOURS
(cold wash)
90º
60º
60º
40º
30º
PROGRAMME FOR
TABLE OF PROGRAMMES
MAX.
LOAD IN
KG
I
II
•
4,5
4,5
4,5
3,5
3,5
3,5
—
PROGRAMME
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
T ºC
P
FAST COLOURS WITH PRE-WASH
FAST COLOURS
FAST COLOURS
DELICATE COLOURS
DELICATE COLOURS
DELICATE COLOURS
(cold wash)
60º
60º
50º
40º
30º
•
2
2
2
2
2
2
•
•
•
•
•
•
•
•
•
•
•
•
P
DELICATES
WOOL
WOOL
(cold wash)
40º
30º
1,5
1
1
—
•
•
•
•
•
•
HAND WASH
RINSE
FAST SPIN
DRAIN ONLY
MIX & WASH SYSTEM
32 MINUTE RAPID PROGRAMME
30º
—
—
—
40º
50º
2
—
—
—
4,5
2
Programme
*
, as per EN standard 60456.
There are four programme groups (COTTON, MIXED/
SYNTHETICS, DELICATES and SPECIALS). The first
programmes in each group are longer and therefore ensure a
more thorough wash. The remaining programmes should be
used with lightly soiled or particularly delicate clothes.
•
•
•
*
DETERGENT
COTTON
MIXED/
SYNTHETICS
DELICA-
TES
SPECIALS
15
SPECIALS
30º
HAND WASH
This washing machine also gas a gentle Hand Wash programme cycle. This programme
allows a complete washing cycle for garments specified as «Hand Wash only» on the
fabric care label. The programme has a temperature of 30ºC and concludes with 2
rinses and a slow spin.
SP1
SPECIAL «RINSE» PROGRAMME
The SP1 programme carries out three rinses with a spin at 800 rpm (which can be
reduced or excluded by using the correct button). It can be used for rinsing any type of
fabric, eg. use after hand-washing.
SPECIAL «FAST SPIN» PROGRAMME
The SP2 programme carries out a spin at 850 rpm (which can be reduced by using the
correct button).
SP2
DRAIN ONLY
The programme SP3 drains out the water.
SP3
«MIX & WASH SYSTEM» PROGRAMME
The Mix & Wash system enables different types of fabric to be washed together.
32 MINUTE RAPID PROGRAMME
This fast wash programme runs through a complete washing cycle for up to 2 kg of
clothes at a temperature of 50º in just 32 minutes. The soap powder must be put into the
wash compartment (compartment II). The maximum quantity of detergent that can be
used is 35 gm. This programme can also be used as a pre-wash for particularly heavily
soiled clothes, before the desired main programme is selected.
REMARKS
1. For heavily soiled clothes, it is advisable to cut maximum load to 3 kg.
2. Automatic bleaching is available on the COTTON (90º WHITE and 60º FAST COLOURS)
programmes: add bleach in the compartment marked .
3. The machine is designed to release fabric softener automatically in the last rinse of all washing
cycles.
40º
50º
16
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
Candy LB CTAS 85 User manual
- Category
- Washing machines
- Type
- User manual
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
Otsein-Hoover LBOHTC 203 User manual
-
Hoover LB HTC 172 User manual
-
-
Terzismo BT610 User manual
-
Iberna LB ITL 856 T User manual
-
-
-
Otsein LB LTO109A User manual
-
-
