EnviroLite EVTR2X4BLLED Installation guide

INSTRUCTIONS MANUAL

LED BACKLIT TROFFER LIGHT

MODEL Nº EVTR2X4T3LED (UPC# 046335977303)

Page 1

Page 2

Thank you for purchasing this EnviroLite Troffer. This product has

been manufactured with the highest standards of safety and

quality.

FEATURES:

1. Easy to install.

QUESTIONS, PROBLEMS, MISSING PARTS:

Before returning to your local store, please call our Customer Service

Team at 1-800-787-1021. Please reference your Model No.

EVTR2X4BLLED or UPC (046335977198).

CAUTION:

1. Before starting installation of this fixture or removal of a previous

fixture, disconnect the power by turning off the circuit breaker or by

removing the fuse at the fuse box.

2. CONSULT A QUALIFIED ELECTRICIAN IF YOU HAVE ANY

ELECTRICAL QUESTIONS. If you have any non-electrical questions

about this fixture, please call our Customer Service Team at 1-800-

787-1021. Please reference your Model No. EVTR2X4BLLED or UPC

(046335977198).

3. KEEP your receipt and these Instructions for Proof of Purchase.

PARTS INCLUDED FOR ASSEMBLY (parts are not to scale):

Page 3

GENERAL:

1. All electrical connections must be in accordance with local, and

national electrical codes.

2. Prior to installation it is important to follow the following guidelines:

A. Turn off the main power at the circuit breaker before installing the

fixture, to prevent possible shock.

B. Be sure that all wires were not damaged during installation and

that there are no rough or sharp edges in contact with the wires.

1 ea LUMINAIRE

INSTALLATION & ASSEMBLY:

1. Remove fixture from box.

2. Open the door frame (#1) by rotating the two

cam latches (#2) [Fig. 1].

3. Remove the lamps (#3) from the packaging

material and put them in a safe place [Fig. 1].

4. Remove the ballast cover (#4) by squeezing

and releasing it from locking tabs (#5) [Fig.

1].

5. Close the door frame (#1) and place the

fixture on a 2 ft by 4 ft T-bar grid in the

desired location [Fig. 2].

6. From above the ceiling, secure troffer to T-

Bar by bending built in T-bar clips (#6) on all

four corners of fixture [Fig. 3].

7. If local code requires, tie a wire to at least two

of the four T-bar clips (#6) to a structural

member of the ceiling.

8. Remove the access plate (#7) and locate

fixture supply wires (1 black & 1 white) [Fig.

3 & 4].

9. Remove one knockout (#8) in access plate

(#7) and pull fixture supply wires through

knockout (#8) opening [Fig. 4 & 5].

10. Make electrical connections according to

local code.

11. From below ceiling, open the door frame (#1)

and replace the wire cover (#4) by

squeezing it into the locking tabs (#5) [Fig.

1].

12. Install lamp (#3) with side labeled “power” on

the lamp holders closest to the access plate

(#7).

13. Close the door frame using the two cam

latches (#2) [Fig. 1].

14. Turn power on.

Page 4

3

Fig. 1

Fig. 3

Fig. 4

Fig. 2

Page 5

Possible Cause Corrective Action

1. Power is off. 1. Make sure power supply is on.

2. Lamps are not

installed correctly.

2. Ensure that the lamp side labeled "power"

is connected to the side closest to the

access plate. Or flip lamp direction.

3. Faulty switch. 3. Test or replace switch.

4. Faulty wire connection. 4. Check wiring.

Fuse blows or circuit

breaker trips when light is

turned on.

1. Crossed wires or

power wire is grounding

out.

1. Check wire connections.

Light will not turn on.

TROUBLESHOOTING:

PRODUCT MAINTENANCE:

1. To clean the outside of the fixture, use a dry or slightly dampened clean cloth

(use clean water, never a solvent) to wipe the surface of the fixture.

2. To clean the inside of the fixture, first disconnect power to the fixture by turning

off the circuit breaker or by removing the fuse at the fuse box. Next, use a dry or

slightly dampened clean cloth (use clean water, never a solvent) to wipe the

interior surface of the fixture.

3. Do not use any cleaners with chemicals, solvents or harsh abrasives. Use only a

dry soft cloth to dust or wipe carefully.

LIMITED WARRANTY

The manufacturer warrants this lighting fixture to be free from defects in materials and

workmanship for a period of three (3) years from date of purchase. This warranty applies only to

the original consumer purchaser and only to products used in normal use and service. If this

product is found to be defective, the manufacturer’s only obligation, and your exclusive remedy, is

the repair or replacement of the product at the manufacturer’s discretion, provided that the product

has not been damaged through misuse, abuse, accident, modifications, alterations, neglect or

mishandling. This warranty shall not apply to any product that is found to have been improperly

installed, set-up, or used in any way not in accordance with the instructions supplied with the

product. This warranty shall not apply to a failure of the product as a result of an accident, misuse,

abuse, negligence, alteration, or faulty installation, or any other failure not relating to faulty material

or workmanship. This warranty shall not apply to the finish on any portion of the product, such as

surface and/or weathering, as this is considered normal wear and tear. The manufacturer does

not warrant and specially disclaims any warranty, whether expressed or implied, of fitness

for a particular purpose, other than the warranty contained herein. The manufacturer

specifically disclaims any liability and shall not be liable for any consequential or incidental

loss or damage, including but not limited to any labor/expense costs involved in the

replacement or repair of said product.

MANUAL DE INSTRUCCIONES

Page 6

LUMINARIA DE LED PARA TECHO SUSPENDIDO

MODELO Nº EVTR2X4T3LED (UPC# 046335977303)

Page is loading ...

MODE D’INSTALLATION

Page 11

MODÈLES Nº EVTR2X4T3LED (CUP Nº 046335977303)

LUMIÈRE DEL POUR PLAFOND SUSPENDU

Page is loading ...

EnviroLite EVTR2X4BLLED Installation guide

EnviroLite EVTR2X4BLLED Installation guide

in other languages

Related papers

Other documents