EnviroLite WL1380DMD40 Installation guide

Brand: EnviroLite

Model: WL1380DMD40

Type: Installation guide

INSTRUCTIONS MANUAL

LED BACKLIT LED WRAP LIGHT

MODEL WL1380DMD40

Thank you for purchasing this EnviroLite LED Wrap. This product

has been manufactured with the highest standards of safety

and quality.

CHARACTERISTICS:

Electrical

System Input Power: 100 W

Input Voltage: 120-277 VAC

Input Frequency:50/60 Hz

Power Factor: > 0.9

Dimmable: 10-100% dimming range with Lutron or Leviton

0-10V dimmers.

For a complete list of compatible dimmers, please

look up the item number listed on the cover of this

instruction manual at http://www.envirolite-LED.com.

Temperature Operating Temperature: -20°C to 45°C

QUESTIONS, PROBLEMS, MISSING PARTS:

Before returning to your local store, please call our Customer Service

Team at 1-800-787-1021. Please reference your Model No.

WL1380DMD40.

CAUTION:

1. Before starting installation of this fixture or removal of a previous

fixture, disconnect the power by turning off the circuit breaker or by

removing the fuse at the fuse box.

2. CONSULT A QUALIFIED ELECTRICIAN IF YOU HAVE ANY

ELECTRICAL QUESTIONS. If you have any non-electrical questions

about this fixture, please call our Customer Service Team at 1-800-

787-1021. Please reference your Model No. WL1380DMD40.

3. KEEP your receipt and these Instructions for Proof of Purchase.

PARTS INCLUDED FOR ASSEMBLY (parts are not to scale):

GENERAL:

1. All electrical connections must be in accordance with local, and

national electrical codes.

2. Prior to installation it is important to follow the following guidelines:

A. Turn off the main power at the circuit breaker before installing the

fixture, to prevent possible shock.

B. Be sure that all wires were not damaged during installation and

that there are no rough or sharp edges in contact with the wires.

WARNING:

• Min 90°C supply conductors, Type IC, INHERENTLY

PROTECTED.

• This product must be installed in accordance with the applicable

installation code by a person familiar with the construction and

operation of the product and the hazards involved.

• Blinking light of this thermally protected luminaire may indicate

overheating.

• Vapor barrier must be suitable for 90°C.

• Suitable for damp locations.

1 Luminaire

INSTALLATION & ASSEMBLY:

1. Turn off the power at the circuit breaker box.

2. Remove the fixture from the packaging.

3. Remove the lens (A) from the fixture (C), then squeeze the

cover (B) and remove it from the fixture (C) (Fig. 1).

MOUNTING METHOD 1

1. Center the fixture over the outlet box in the desired location

and mark the mounting holes with a pencil.

2. Drill the appropriately sized mounting holes in at each

marked location. Anchors or other hardware may be needed

depending on the surface type.

3. Insert the black supply wire and the white supply wire

into the empty quick connector (D) (Fig. 2).

4. Pull the quick connector (E) through the central knockout

hole (F). (Fig. 3).

5. Connect the fixture quick connector (E) to the power

supply quick connector (D). Connect the supply ground

wire to the fixture ground wire using a wire nut.

6. Connect the purple and grey wires from the dimmer to

corresponding wires of the wall 0-10V dimmer (Fig. 4).

7. Restore power at the circuit breaker box.

MOUNTING METHOD 2

1. Place the fixture in the desired location and mark the

mounting holes with a pencil.

2. Drill the appropriately sized mounting holes in at each

marked location. Anchors or other hardware may be needed

depending on the surface type.

3. Use the knockout on the end cap of the fixture to bring in the

supply wires.

4. Insert the black supply wire and the white supply wire

into the empty quick connector (D) (Fig. 2).

5. Pull the quick connector (E) through the end cap

knockout hole.

6. Connect the fixture quick connector (E) to the power

supply quick connector (D). Connect the supply ground

wire to the fixture ground wire using a wire nut.

7. Connect the purple and grey wires from the dimmer to

corresponding wires of the wall 0-10V dimmer (Fig. 4).

8. Restore power at the circuit breaker box.

Fig. 3

Fig. 2

Fig. 1

Fig. 4

PURPLE PURPLE

GREY GREY

FIXTURE WIRES DIMMER WIRES

TROUBLESHOOTING:

PRODUCT MAINTENANCE:

1. To clean the outside of the fixture, use a dry or slightly dampened clean cloth

(use clean water, never a solvent) to wipe the surface of the fixture.

2. To clean the inside of the fixture, first disconnect power to the fixture by turning

off the circuit breaker or by removing the fuse at the fuse box. Next, use a dry or

slightly dampened clean cloth (use clean water, never a solvent) to wipe the

interior surface of the fixture.

3. Do not use any cleaners with chemicals, solvents or harsh abrasives. Use only a

dry soft cloth to dust or wipe carefully.

LIMITED WARRANTY

The manufacturer warrants this lighting fixture to be free from defects in materials and

workmanship for a period of five (5) years from date of purchase. This warranty applies only to the

original consumer purchaser and only to products used in normal use and service. If this product is

found to be defective, the manufacturer’s only obligation, and your exclusive remedy, is the repair

or replacement of the product at the manufacturer’s discretion, provided that the product has not

been damaged through misuse, abuse, accident, modifications, alterations, neglect or mishandling.

This warranty shall not apply to any product that is found to have been improperly installed, set-up,

or used in any way not in accordance with the instructions supplied with the product. This warranty

shall not apply to a failure of the product as a result of an accident, misuse, abuse, negligence,

alteration, or faulty installation, or any other failure not relating to faulty material or workmanship.

This warranty shall not apply to the finish on any portion of the product, such as surface and/or

weathering, as this is considered normal wear and tear. The manufacturer does not warrant and

specially disclaims any warranty, whether expressed or implied, of fitness for a particular

purpose, other than the warranty contained herein. The manufacturer specifically disclaims

any liability and shall not be liable for any consequential or incidental loss or damage,

including but not limited to any labor/expense costs involved in the replacement or repair

of said product.

Problem

Cause

Solution

Light will not turn on.

1. Power is off.

1. Make sure power supply is on.

2. Faulty switch.

2. Test or replace switch.

3. Faulty wire connection.

3. Check wiring.

Fuse blows or circuit breaker

trips when light is turned on.

1. Crossed wires or power wire

is grounding out.

1. Check wire connections.

Page is loading ...

EnviroLite WL1380DMD40 Installation guide

Brand: EnviroLite

Model: WL1380DMD40

Type: Installation guide

Download PDF

report

in other languages

français: EnviroLite WL1380DMD40 Guide d'installation
español: EnviroLite WL1380DMD40 Guía de instalación

EnviroLite WL1380DMD40 Installation guide

EnviroLite WL1380DMD40 Installation guide

in other languages

Related papers

Other documents