Home Decorators Collection HB7055A-48 Operating instructions

HOME

DECORATORS

C O L L E C T I O N

Exterior Incandescent Wall Lantern

Hyannis

SKU 322-921 (UPC 046335974715)

(Bronze Finish)

INSTRUCTION MANUAL

Page 1

HB7055A-48 E/S/F

Thank you for purchasing this Home Decorators Collection exterior

light fixture. This product has been manufactured with the highest

standards of safety and quality.

FEATURES:

1. Exterior Incandescent Wall Lantern in Bronze Finish.

2. Timeless elegant design.

3. Easy to assemble and install.

QUESTIONS, PROBLEMS, MISSING PARTS:

Before returning to your local Home depot, please call our Customer

Service Team at 1-800-986-34600 or visit www.homedepot.com. Please

reference your SKU (322-921Bronze Finish fixture) or UPC

(046335974715).

Page 2

CAUTION:

1. Before starting installation of this fixture or removal of a previous

fixture, disconnect the power by turning off the circuit breaker or

by removing the fuse at the fuse box.

2. CONSTULT A QUALIFIED ELECTRICIAN IF YOU HAVE ANY

ELECTRICAL QUESTIONS.

3. If you have any non-electrical questions about this fixture, please

contact our Customer Service Team at 1-800-986-3460 or visit

www.homedepot.com. Please reference your SKU (322-921 Bronze

Finish fixture) or UPC (046335974715).

4. Keep your receipt and these Instructions for Proof of Purchase.

TOOLS REQUIRED FOR ASSEMBLY & INSTALLATION

(not included):

Page 3

Phillips Screwdriver

Exterior Silicon

Rubber Sealant

Wire StrippersWire Cutters

Safety Glasses Electrical Tape

Light Bulb (60 W Max.

or CFL equivalent)

PARTS INCLUDED (parts are not to scale):

Page 4

(1) Fixture Body(1) Glass Shade

(1) Hex Nut(3) Wire Nuts (1) Thumb Lock Nut

(1) Mounting Bracket

(2) Bracket

Mounting Screws

(1) Nipple

INSTALATION & ASSEMBLY:

1. Shut off power at the fuse box or circuit breaker box. Remove the old

fixture, including the mounting hardware.

2. Carefully unpack your new fixture and lay out all the parts on a clear

surface. Take care not to lose any small parts necessary for

installation.

3. Thread the Hex Nut onto the Nipple. Thread the Nipple into the

center hole of the Mounting Bracket. Do not tighten the Hex Nut at

this time. (Fig. 1)

4. Attach the Mounting Bracket to the Outlet Box using the Bracket

Mounting Screws. (Fig. 1)

5. Pull the Supply Wires out from the Outlet Box. Strip approximately

¼” of insulation from each Supply and Fixture Wire.

Page 5

Wall

Bracket Mounting Screw

Mounting Bracket

Hex Nut

Power Supply Wires

Outlet Box

Fig. 1

Nipple

INSTALLATION & ASSEMBLY (cont.):

6. Attach the Black Fixture Wire to the Black Supply Wire using a Wire

Nut, then the White Fixture Wire to the White Supply Wire using a

Wire Nut. Attach the Ground Fixture Wire to the Supply Ground

Wire using a Wire Nut. (Fig. 2)

7. Wrap all wire connections with electrical tape for a more secure

connection. Carefully tuck the wires and wire connections into the

Outlet Box.

8. Place the Wall Plate of the Fixture Body flush against the Wall over

the Outlet Box. Make sure that the Nipple feeds though the hole of

the Wall Plate. Adjust the Nipple so that it protrudes about ¼ inch

from the surface of the Wall Plate Remove the Wall Plate from the

wall and tighten the Hex Nut against the Mounting Bracket. Place the

Wall Plate over the Outlet Box and thread the Thumb Lock Nut onto

the Nipple to secure the Wall Plate against the Wall. (Fig. 2)

Page 6

Black

Supply

Wire

Wire Nut

Black

Fixture

Wire

White

Supply

Wire

White

Fixture

Wire

Supply

Ground

Wire

Fixture

Ground

Wire

Wall

Outlet

Box

Wall Plate

Thumb

Lock Nut

Fig. 2

INSTALLATION & ASSEMBLY (cont.):

9. Install up to a 60 watt Light Bulb or Listed SBCFL (Self-Ballasted

Compact Fluorescent Lamp [not provided]) in the socket of the

Fixture Body . Do not exceed a 60 watt incandescent light bulb, or

a 13 watt SBCFL. (Fig. 3)

10. Slide the Glass Shade into the Fixture Body and turn it clockwise

until secure.

11. Using an exterior rubber sealant, caulk around the edges of the

upper two-thirds of the Wall Plate. Leave the bottom third unsealed

to allow drainage of any water that might leak into the enclosure.

Page 7

Glass Shade

Fixture Body

Wall Plate

Wall

Incandescent Bulb

Fig. 3

TROUBLESHOOTING:

PRODUCT MAINTENANCE:

1. To clean the outside of the fixture, use a dry or slightly dampened clean cloth (use

clean water, never a solvent) to wipe the glass and surface of the fixture.

2. To clean the inside of the fixture, first disconnect power to the fixture by turning off

the circuit breaker or by removing the fuse at the fuse box. Next, use a dry or slightly

dampened clean cloth (use clean water, never a solvent) to wipe the inside glass and

interior surface of the fixture.

3. Do not use any cleaners with chemicals, solvents or harsh abrasives. Use only a dry

soft cloth to dust or wipe carefully.

LIMITED WARRANTY

The manufacturer warrants this lighting fixture to be free from defects in materials and workmanship for a

period of three (3) years from date of purchase. This warranty applies only to the original consumer

purchaser and only to products used in normal use and service. If this product is found to be defective, the

manufacturer’s only obligation, and your exclusive remedy, is the repair or replacement for the product at

the manufacturer’s discretion, provided that the product ahs not been damaged through misuse, abuse,

accident, modifications, alterations, neglect, or mishandling. This warranty shall not apply to any product

that is found to have been improperly installed, set-up, or used in any way not in accordance with the

instructions supplied with the product. This warranty shall not apply to a failure of the product as a result of

an accident, misuse, abuse, negligence, alteration, or faulty installation, or any other failure not relating to

faculty material or workmanship. This warranty shall not apply to the finish on any portion of the product,

such as surface and/or weathering, as this is considered normal wear and tear.

The manufacturer does not warrant and specially disclaims any warranty, whether express or implied

of fitness for a particular purpose, other than the warranty contained herein. The manufacture

specifically disclaims any liability and shall not be liable for any consequential or incidental loss or

damage, including but not limited to any labor/expense cost involved in the replacement or repair of

said product.

Page 8

Symptom Possible Cause Corrective Action

1. Power is off. 1. Make sure power supply is on.

2. Faulty switch. 2. Test or replace switch.

3. Faulty wire connection. 3. Check wiring.

Fuse blows or circuit breaker

trips when light is turned on.

1. Crossed wires or power wire is grounding

out.

1. Check wire connections.

Light will not turn on.

Page is loading ...

HOME

DECORATORS

C O L L E C T I O N

Lanterne Murale Incandescent

Hyannis

SKU 322-921 (UPC 046335974715)

(Finition Bronze)

MANUEL D'INSTRUCTIONS

Page 17

HB7055A-48 E/S/F

Page is loading ...

Home Decorators Collection HB7055A-48 Operating instructions

Home Decorators Collection HB7055A-48 Operating instructions

in other languages

Related papers

Other documents